How long does it take to practice forward and backward movements in Subject 2?

What is the actual measured ground clearance of the Edge?

According to official data, the actual measured ground clearance of the Edge is 201 millimeters, but its minimum ground clearance is 16 centimeters. Ground clearance refers to the distance between the lowest point of the chassis under maximum allowable load and the level ground, which indirectly indicates the vehicle's performance when climbing slopes. Minimum ground clearance: The minimum ground clearance indicates the vehicle's ability to overcome obstacles. The smaller the ground clearance, the worse the ability to overcome obstacles. The larger the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven terrain, but with a higher center of gravity, which reduces stability. The smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven terrain, but with a lower center of gravity, which can increase stability. Characteristics of clearance size: Ground clearance is related to the vehicle's load—the heavier the load, the smaller the ground clearance. Vehicles with small ground clearance have a low center of gravity but poor off-road capability. Vehicles with large ground clearance have good off-road capability, and high ground clearance not only provides good performance on gravel or mountainous roads but also prevents water from entering the exhaust pipe when driving through flooded roads, making it easier to park on curbs or parking spaces with height differences.

17

2

Share

Why Does Beijing Restrict Non-local Vehicles?

Starting from November 1, 2019, the "Restriction Policy on Non-local License Plate Vehicles" will be officially implemented in Beijing. According to the "Notice on Traffic Management Measures for Some Passenger Vehicles in Beijing" (hereinafter referred to as the "Notice"), non-local license plate vehicles can apply for a Beijing Entry Permit a maximum of 12 times per year, with each permit valid for up to 7 days. The following is relevant information: 1. Relevant Regulations: According to the newly released "Notice on Traffic Management Measures for Non-local Passenger Vehicles Entering Beijing," starting from January 1, non-local license plate passenger vehicles, including those with temporary license plates, must obtain a Beijing Entry Permit and a Beijing Urban Area Permit if they intend to drive within the Fifth Ring Road (inclusive) of Beijing. 2. Reasons for Restrictions: Trading quotas, the second-hand car market, and public auctions—"8-year quota, 8-year quota, price is not high"—refer to this situation. There are two scenarios: one involves the quota holder selling it themselves, which is relatively safer; the other involves an unknown number of intermediaries, naturally increasing the risk significantly.

6

1

Share

What is the ground clearance of the Mercedes-Benz GLC?

The minimum ground clearance of the Mercedes-Benz GLC is 180 millimeters. The minimum ground clearance of the Mercedes-Benz GLC refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which is used to indicate the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. A higher ground clearance for the Mercedes-Benz GLC improves its off-road capability, but if the ground clearance is too high, the stability at high speeds may decrease. The Mercedes-Benz GLC is the first all-new crossover model launched by Mercedes-Benz, released in 2015. Essentially, the Mercedes-Benz GLC can be considered as the coupe version of the GLK. The dimensions of the Mercedes-Benz GLC are 4764 millimeters in length, 1898 millimeters in width, 1642 millimeters in height, with a wheelbase of 2973 millimeters. Generally, the ground clearance of sedans ranges between 110 millimeters and 150 millimeters, while SUVs have a ground clearance between 200 millimeters and 250 millimeters. However, the ground clearance of the Mercedes-Benz GLC is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the load variations of the Mercedes-Benz GLC. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban areas with well-paved roads, a vehicle with lower ground clearance can enhance stability and comfort. If frequently traveling to remote areas or driving on rough terrains, a vehicle with higher ground clearance may be preferred to avoid scraping or damaging the chassis, considering its off-road performance.

7

0

Share

What is the Side Rear Vehicle Alert Function?

Rear vehicle warning light will illuminate, this is the Lane Change Assist system. Below is relevant information: 1. Introduction: During driving, due to vehicle body design, the visual range provided by side mirrors always has some blind spots. Drivers cannot constantly turn their heads, which actually increases driving risks. 2. Principle: The Lane Change Assist system alerts the driver to approaching vehicles from behind through indicators in the left/right mirrors or other locations. This system automatically activates only when changing lanes above 60 km/h, and won't function at lower speeds. It can detect vehicles approaching from up to 50 meters in the side rear area.

6

3

Share

What is the fuel tank capacity of the 2013 Buick LaCrosse?

2013 Buick LaCrosse has a fuel tank capacity of 70 liters, which is the officially announced data. The 2013 Buick LaCrosse 2.0T version requires 95-octane gasoline, while other versions use 92-octane. The fuel consumption per 100 kilometers ranges from 7.2 to 9.9 liters, and a full tank can cover a distance of 707 to 972 kilometers. During daily driving, it is necessary to pay attention to the remaining fuel level in the tank. The fuel level is usually observed through the fuel gauge inside the car. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge typically has 5 to 6 segments. It is advisable to refuel when there are only 2 segments left to avoid running out of fuel midway. During actual refueling, the amount of fuel may exceed the calibrated capacity. This is because the fuel tank capacity marked by the manufacturer is measured from the bottom of the tank to the safety level, and there is still some space from the safety level to the tank opening. This space is reserved to allow for fuel expansion when the temperature rises, preventing overflow. If fuel is added up to the tank opening during refueling, the actual amount of fuel added may exceed the calibrated tank capacity.

5

4

Share

What is the cylinder bore diameter?

The cylinder bore diameter varies from small to large, ranging from 32 millimeters to 250 millimeters, with different cylinders having different bore sizes. The following is an introduction to cylinder bore diameter: Introduction to cylinder bore diameter: In an engine, the piston moves in a reciprocating linear motion within the cylinder, and the diameter of the cylinder is referred to as the bore diameter. Determination of bore diameter: The total traction force, total thrust, and movement speed of the oil cylinder are generally known, and the stroke length is determined by work requirements (it is also considered known, with the length of the oil cylinder preferably not exceeding 20 times its diameter). When the total thrust remains constant, the diameter of the oil cylinder is inversely proportional to the square root of the working pressure. A smaller diameter (for compactness) and lower pressure (for simpler systems and fewer leaks) are desirable. The principle for resolving such conflicting requirements is to select the lowest possible working pressure while ensuring an appropriate diameter size. When determining the size of the oil cylinder, different factors are considered for different types of machine tools, including the determination of the bore diameter. Stroke-to-bore ratio: The stroke-to-bore ratio is the most fundamental and critical structural parameter of an internal combustion engine. It not only significantly affects scavenging quality and heat transfer but also influences the engine's power and fuel consumption rate. Additionally, it affects the structure and size of all components, thereby impacting the engine's vibration, specific weight index, and service life. Stroke gasoline engines generally employ loop scavenging, where fresh mixture is used to expel the remaining exhaust gas from the cylinder through the exhaust port. The more thoroughly the exhaust gas is expelled from the cylinder and the less fresh mixture is lost with the exhaust gas (a situation referred to as good scavenging quality), the greater the engine's power and the lower its fuel consumption rate.

3

0

Share

How long does it take to practice forward and backward movements in Subject 2?

What is the actual measured ground clearance of the Edge?

Why Does Beijing Restrict Non-local Vehicles?

What is the ground clearance of the Mercedes-Benz GLC?

What is the Side Rear Vehicle Alert Function?

What is the fuel tank capacity of the 2013 Buick LaCrosse?

What is the cylinder bore diameter?

How to Replace the Coolant in a Volkswagen Passat?

How often should the fuel filter be replaced in the new Passat?

What is the fuel tank capacity of the Elantra?

Does Engine Sludge Need to Be Cleaned?