How Long Does It Take to Get License Plates After Vehicle Inspection?

1 Answers
MacFelix
07/29/25 11:53am
Completing vehicle inspection and license plate selection typically takes about half a day. If the owner is in a hurry, the entire process can be completed within one day, with the latest completion time being approximately 2 working days. Below is an introduction to vehicle license plates: 1. Overview: License plates, commonly known as vehicle plates, are panels mounted on the front and rear of a vehicle. They are usually made of aluminum, sheet metal, plastic, or paper, and display the vehicle's registration number, registration region, and other relevant information. 2. Function: License plates serve as identifiers and information records for vehicles. Their primary purpose is to indicate the vehicle's registered region and allow authorities to trace the vehicle's owner and registration details. 3. Temporary Plates: Temporary license plates are provisional driving permits issued by the vehicle management department of the public security bureau when a vehicle has not yet been officially registered due to pending procedures.
Was this review help?
5
0
Share
More Forum Discussions

How to Set Up a Car Alarm to Trigger Upon Touch?

To set up a car alarm that triggers upon touch, you need to install an alarm system for the vehicle and adjust its sensitivity to the highest level. Below are the specific steps to adjust the sensitivity of the car alarm: 1. Unlock the car and enter the vehicle, then press and hold the unlock button on the key for 5 seconds until the turn signals stay lit. 2. The vehicle will enter the alarm sensitivity setting mode. Without pressing the brake pedal, press the engine start button. 3. There are five levels of sensitivity in total, with level one being the lowest and level five the highest. Each press of the start button increases the sensitivity by one level. 4. It is generally not recommended to set the sensitivity to the highest level, as this may cause the alarm to trigger too easily. Usually, setting it to level three or four is more appropriate.
14
4
Share

Is Brake Disc Rust a Serious Issue?

Brake disc rust is not a serious issue and is a normal phenomenon. The rust on brake discs is mainly caused by the vehicle being parked for extended periods, excessively humid air, or rain and snow. When parking the vehicle, it is advisable to choose a covered or relatively dry location to some extent avoid rust. Simply put, a brake disc is a round disc that rotates as the vehicle moves. The brake caliper clamps the brake disc to generate braking force, slowing down or stopping the vehicle when the brakes are applied. The method for replacing a brake disc is as follows: 1. Open the engine compartment and check the brake fluid level to prevent overflow during replacement; 2. Remove the wheel where the brake is located and the bolts of the brake caliper; 3. Take off the old brake disc, install the new one, tighten the guide bolts, and complete the replacement.
11
2
Share

How to adjust the steering wheel weight of Haval H6?

Haval H6 steering wheel weight adjustment methods are as follows: 1. Haval H6 uses an electric power steering system, which can be adjusted: (1) There is a small lever below the steering wheel, pull it down; (2) Then the steering wheel can be adjusted up and down; (3) After adjustment, reset the lever. 2. Haval H6 uses a mechanical hydraulic power steering system, which cannot be adjusted. The following is an introduction to Haval H6: 1. Haval H6 comes standard with configurations such as headlight height adjustment, headlight delay-off, four-way steering wheel adjustment, dual airbags, and rear air conditioning vents. 2. High-end models are equipped with intelligent and convenient configurations such as cruise control system, intelligent voice GPS navigation system, intelligent wiper and light control, side airbags and front-rear integrated side safety air curtains, ESP electronic stability system, and tire pressure monitoring system.
9
2
Share

What is the Principle of Air Suspension?

Here is how air suspension works: 1. It utilizes an air compressor to generate compressed air, which is then used to adjust the vehicle's ground clearance; 2. Vehicles equipped with air springs generally have ground clearance sensors near the front and rear wheels. Based on the output signals from these sensors, the onboard computer detects changes in vehicle height and controls the air compressor and exhaust valves accordingly, causing the springs to automatically compress or extend to achieve a damping effect; 3. Air suspension also enhances the vehicle's adaptability. At high speeds, it can automatically stiffen to improve stability, while during prolonged low-speed driving on uneven roads, the onboard computer softens the suspension to enhance comfort; 4. Air suspension is not a recent technological development. The fundamental design is similar across systems, primarily consisting of an air spring filled with compressed air and a shock absorber with variable damping.
11
0
Share

How to Disassemble the Highlander Navigation System?

The method to disassemble the Highlander navigation system is as follows: Before removing the navigation, use a trim removal tool to pry loose the air vents, remove the surrounding decorative panels, disconnect the internal plugs and the air conditioning regulator, then unscrew the fixing screws. This will allow the car's navigation system to be removed. During the disassembly process, it's important to note that the navigation system contains numerous internal wires. Avoid applying excessive force to prevent damaging the wiring. The Highlander is a mid-size 5-door, 5-seat SUV with dimensions of 4890mm in length, 1925mm in width, and 1720mm in height, and a wheelbase of 2790mm. It is equipped with a 2.0T turbocharged engine, delivering a maximum power of 162 kW and a maximum torque of 350 Nm. The front suspension uses a MacPherson strut independent suspension, while the rear suspension employs an E-type multi-link independent suspension.
15
0
Share

Where is the Pajero Transmission Dipstick Located?

The Pajero transmission dipstick is located on the transmission. The method for checking the transmission fluid level involves the following steps: 1. Park the vehicle on a level surface and engage the parking brake. 2. Allow the engine to idle for at least one minute. 3. Depress the brake pedal and shift the gear selector through each position (Reverse (P), Drive (D), Low gears (S, L or 2, 1)), pausing for a few seconds in each to ensure the torque converter and all shift components are filled with hydraulic fluid. Finally, shift back to Park (P). 4. Remove the automatic transmission dipstick from the filler tube, wipe it clean, reinsert it fully, then remove it again to check the fluid level. 5. If the fluid level is between the maximum and minimum marks, the level is correct. If below the minimum mark, add transmission fluid. If above the maximum mark, the transmission has been overfilled.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.