How long does it take to fully charge the battery when the Geely Emgrand engine is running?

2 Answers
Larry
08/26/25 4:27am
It takes about half an hour to fully charge the battery when the Geely Emgrand engine is running. Charging via the switch circuit: The battery power consumed during startup is recharged through the vehicle's switch circuit. Charging can occur while idling, but the charging current is relatively small. If the battery is completely drained, idling for half an hour after jump-starting the engine will allow you to check the dashboard for charging status. Charging conditions: Generally, car batteries are rarely charged only when completely depleted, so charging times vary between vehicles. If the battery is indeed fully discharged, it typically requires about 12 hours of charging. The exact time depends largely on the battery's condition. Additionally, charging a car's starter battery usually takes around 20 hours.
Was this review help?
6
1
Share
DiBethany
09/08/25 5:49am
Having driven for several years, especially with common models like the Geely Emgrand, charging the battery really depends on the specific situation. It mainly hinges on several key factors: first, the battery's own discharge level—if it's almost dead, idling to charge might take 40 minutes to an hour just to restore enough power to start the car; second, the vehicle's driving state—driving at high speeds, say above 80 km/h, allows the alternator to output more, so 15-20 minutes can charge it significantly, but idling in city traffic is too slow; third, what electrical devices you're using—running the AC or headlights diverts current, prolonging charging time. Generally, short trips like a 10-minute commute won't fully charge the battery, leading to premature failure. It's recommended to drive at high speeds for about half an hour to maintain battery health, and avoid leaving the car idle too often. A healthy battery ensures a longer vehicle lifespan—running out of power halfway is a real hassle.
Was this review help?
6
2
Share
Expand All
More Forum Discussions

What is the reason for loud engine noise and slow acceleration?

Loud engine noise and slow acceleration are caused by issues with the timing belt and valve clearance. Timing Belt Fault: If the timing belt is off by one tooth, the engine sound will be abnormal. The noise at high RPMs will be very loud, and there may be difficulty starting the engine. Immediate repair is necessary to avoid damaging the engine. Valve Clearance Fault: If the valve clearance is too small, the engine will lack power and produce a muffled sound. If the valve clearance is too large, there will be significant noise and difficulty starting. This issue is related to the engine's configuration. It is recommended to visit a reliable auto repair shop to adjust the engine configuration.
3
2
Share

Where to Turn On Bluetooth in the Car?

In-car Bluetooth is referred to as Car-Bluetooth-Phone, abbreviated as CBP. There is no dedicated button for turning it on or off inside the car; all operations, including turning Bluetooth on and off, are performed through the central control screen. The functions of in-car Bluetooth are as follows: 1. Answering calls: In-car Bluetooth technology originates from mobile phone Bluetooth, with the primary purpose of allowing drivers to answer calls hands-free without touching their phones while driving, simply by using the answer button on the multifunction steering wheel. This not only simplifies the process of answering calls but also enhances driving safety. 2. Entertainment: The in-car Bluetooth feature also enables wireless playback of music from mobile phones, adding some fun for passengers during dull and boring journeys, which can indirectly improve driving safety.
15
4
Share

Is it necessary to perform maintenance at a 4S store to keep the warranty valid?

It is not mandatory to perform maintenance at a 4S store to keep the warranty valid. Characteristics of automobile 4S stores: Automobile 4S stores are invested and constructed by dealers according to the standards set by automobile manufacturers. 4S stores and automobile manufacturers jointly form a brand alliance, representing the brand culture and value, and enhancing the brand's reputation and credibility for the manufacturer. Purpose of automobile maintenance: The purpose of automobile maintenance is to keep the vehicle clean and in good technical condition, eliminate potential hazards, prevent failures, slow down the deterioration process, and extend the service life.
11
2
Share

Which has more power, the Honda CL400 or the CB400SS?

The maximum power output of both motorcycles is the same Honda CL400: The CL400 is Honda's retro motorcycle featuring family-style design with dual exhaust pipes extending from the front of the engine and placed at the midsection of the body, showcasing elegant curves. The heat shields also receive chrome plating treatment. As a tribute to Honda's CL series, the Honda CL400 perfectly interprets the essence of CL models. It deliberately omits modern configurations, allowing riders to fully experience the joy of human-machine interaction. Its appearance evokes memories of classic models from the 1960s-1970s. Honda CB400SS: The Honda CB400SS delivers linear power output and offers agile handling, primarily designed for urban commuting.
20
2
Share

What is SP5W30 engine oil?

5W30 is an engine oil that is more suitable for regions with lower temperatures. Below is relevant information about engine oil: 1. Mineral oil: Mineral oil is the residue left after gasoline and heavy oil are extracted from petroleum. In fact, mineral oil is also a natural oil, but it contains more impurities. Compared to semi-synthetic and fully synthetic oils, it is cheaper, provides poorer lubrication for the engine, and has a shorter service life. 2. Semi-synthetic oil: Semi-synthetic oil falls between mineral oil and fully synthetic oil. It contains a large amount of anti-corrosion additives to enhance the oil's stability and high oxidation resistance. 3. Fully synthetic oil: Among these three types of engine oils, fully synthetic oil is of the highest quality and durability, and it is also the most expensive. Generally, it can be used in cars for 10,000 to 12,000 kilometers without deteriorating.
6
5
Share

What is the Difference Between Solid Titanium Wheels and Pneumatic Wheels?

The following are the differences between solid titanium wheels and pneumatic wheels: 1. Different materials: (1) Pneumatic wheels are made of leather and rubber-coated canvas, yet this type of tire has shown the advantage of low rolling resistance. (2) Solid titanium wheels are wheels where rubber is directly vulcanized onto the rim. 2. Different wear resistance: (1) Pneumatic wheels have no friction between the inner and outer tires, and heat can be dissipated directly through the rim, resulting in lower tire temperature, stronger wear resistance, and longer service life. (2) Solid titanium wheels have poorer wear resistance and are easily corroded and aged by organic solvents, strong acids, and weak alkalis.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.