How long does it take to complete the Subject 2 driving test?

Should rear passengers in motor vehicles wear seat belts?

Rear passengers in motor vehicles should wear seat belts, as explicitly stipulated by the Road Traffic Safety Law. When a motor vehicle is in motion, both the driver and passengers must use seat belts in accordance with regulations. The working principle of seat belts is as follows: in the event of a collision or emergency braking, the pre-tensioning device instantly retracts, tightening the slack seat belt to firmly secure the occupant in the seat, preventing secondary collisions. The method for replacing a seat belt is as follows: 1. Locate the wiring under the car seat and find the sensor wire for the seat belt buckle; 2. Remove the seat cushion, deactivate the airbag, locate the bolt securing the seat belt, and remove the seat belt buckle; 3. Find the seat cushion sensor inside the seat cushion and remove it; 4. Install the new seat belt buckle onto the seat and insert the bolt; 5. Install the weight sensor on the car seat, then attach the new retractor and tighten it with a wrench; 6. Restore the car seat cushion to its original position and neatly arrange the wiring at the bottom of the seat.

13

1

Share

How Do Drivers Judge the Distance Between Cars?

Drivers judge the distance between cars by the following methods: 1. When the upper edge of the rear bumper of the car in front is visible, the distance is 1 meter; 2. When the lower edge of the rear bumper of the car in front is visible, the distance is 2 meters; 3. When the lower edge of the rear tire of the car in front is visible, the distance is 3 meters; 4. If the car's reflection occupies the entire rearview mirror, the distance is 3 meters; if it occupies two-thirds of the rearview mirror, the distance is 5 meters; if it occupies half of the rearview mirror, the distance is 9 meters; if it occupies one-third of the rearview mirror, the distance is 12 meters. Reasons for maintaining distance: 1. To avoid rear-end collisions caused by sudden braking of the car in front; 2. To reserve reaction time for handling emergencies.

5

2

Share

Where is the central point for left turns in Subject 3?

The central point for left turns in Subject 3 is marked with corresponding signs on the road. Not turning left near the central point of the intersection means that when a motor vehicle makes a left turn at an intersection controlled by traffic signals without turning near the left side of the central point, it constitutes a traffic violation, violating Article 51 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China". Below is an introduction to Subject 3: 1. Definition of Subject 3: Subject 3 includes the road driving skills test and the safe and civilized driving knowledge test, which are part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safe and civilized driving knowledge test in the motor vehicle driver's examination. The content of the road driving skills test varies for different types of vehicles. 2. Test content of Subject 3: (1) The road driving skills test generally includes: preparation before driving, simulated light test, starting, driving straight, gear shifting operations, changing lanes, parking by the roadside, going straight through intersections, left turns at intersections, right turns at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting vehicles, overtaking, making U-turns, and driving at night. (2) The safe and civilized driving knowledge test generally includes: requirements for safe and civilized driving operations, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and knowledge of post-accident handling procedures.

10

5

Share

What are the dimensions of the Clever?

Its length is 3140mm, width is 1648mm, height is 1521mm (1531mm with shark fin antenna), and the wheelbase is only 2000mm, which is significantly smaller than the already discontinued Roewe E50. The Roewe Clever features a compact body with large headlights, and its side design is quite simple. The Clever's body dimensions are small, positioning it as a microcar. Additional info: The Clever's wheels use basic black steel rims paired with 175/60R13 Cheng Shin CS868 series tires, which enhance the strength of the tread, shoulder, and sidewall.

6

4

Share

How to Reset the Engine Malfunction Light?

The methods to reset the engine malfunction light are: 1. Visit a 4S shop or auto repair shop to use a fault code reader for troubleshooting; 2. Disconnect the negative terminal of the battery to clear the fault codes. The reasons for the engine malfunction light illuminating include: 1. Poor gasoline quality leading to incomplete combustion of the air-fuel mixture in the cylinders, resulting in carbon deposits; 2. Excessive mileage causing weakened spark plug performance; 3. Aging vehicle components; 4. Damaged, poorly connected, or interrupted signals from sensors such as coolant temperature, crankshaft position, air flow, intake temperature, and oxygen sensors. Solutions for the engine malfunction light include: 1. Promptly inspect the engine's condition; 2. Check the status of sensors, air flow sensors, and spark plugs; 3. Check for engine knocking; 4. Inspect the ignition coils for faults; 5. Clean carbon deposits from the engine.

3

2

Share

Why are used Roewe RX5 so cheap?

Roewe RX5 used cars are inexpensive for the following reasons: Resale value: The main reason is that Roewe RX5 has a low resale value, so when sold as a used car, the price is relatively low. Factors contributing to the low resale value include the small market share of the vehicle and relatively high maintenance costs. Before reaching scrap standards: If a car has not yet reached the national scrap standards or can still be used during its economic lifespan, it can be traded as a used car. Choosing to buy a used car is also a wise decision. With the continuous development of the automotive industry, the performance of cars is constantly improving, and vehicle emissions can be gradually reduced. By implementing vehicle emission standards, atmospheric pollutants emitted by cars can be directly reduced at the source.

10

0

Share

How long does it take to complete the Subject 2 driving test?

Should rear passengers in motor vehicles wear seat belts?

How Do Drivers Judge the Distance Between Cars?

Where is the central point for left turns in Subject 3?

What are the dimensions of the Clever?

How to Reset the Engine Malfunction Light?

Why are used Roewe RX5 so cheap?

Are the Tires Replaced at 4S Stores Genuine OEM Tires?

How Many Times Can You Take the Driving License Test Subject 1?

How to Effectively Prevent Stalling When Starting a Manual Transmission Car?

Where is the Honda Civic produced?