How long does it take to complete the required hours for Subject 2?

1 Answers
RubyLynn
07/30/25 10:58am
Subject 2 requires 16 hours to complete. Below is relevant information about Subject 2: Basic Introduction: Also known as the small road test, it is part of the motor vehicle driver's license examination, referred to as the field driving skills test. The full score is 100 points, with evaluation criteria set for failing, deducting 20 points, deducting 10 points, and deducting 5 points. Meeting the requirements means passing the test; Test Content: For small cars, small automatic transmission passenger vehicles for the disabled, and low-speed trucks, the test includes reversing into a garage, stopping and starting on a slope, parallel parking, curve driving, and turning at a right angle. For small automatic transmission cars, the test includes reversing into a garage, parallel parking, curve driving, and turning at a right angle.
Was this review help?
5
5
Share
More Forum Discussions

How to Apply for an International Driver's License?

International driver's licenses cannot be applied for. China has not joined the United Nations Road Traffic Convention, so residents of mainland China cannot apply for an international driver's license. Only compatriots from Hong Kong, Macau, and Taiwan can apply for one. You can only apply for the People's Republic of China Motor Vehicle Driver's License from the traffic management department of the public security authority. Relevant information about the driver's license is as follows: 1. Introduction: The People's Republic of China Motor Vehicle Driver's License, referred to as the driver's license or 'driver's permit,' is a mandatory document for motor vehicle drivers, established in accordance with the laws of the People's Republic of China. 2. Examination Content: The test subjects include traffic regulations and related knowledge, field driving, and road driving (including safe and civilized driving), totaling three items.
9
1
Share

Is it normal for a car's engine oil temperature to display 100 degrees?

A car's engine oil temperature displaying 100 degrees is normal. There are several reasons for a car's engine oil temperature to show 100 degrees: 1. When driving at normal speed, the cooling effect of the coolant will lower the oil temperature. During normal speed driving, the oil temperature will drop to around 80-90 degrees due to the cooling effect of the coolant. 2. When driving at low speeds, the cooling effect of the coolant decreases, causing the oil temperature to rise. At low speeds, the coolant's effectiveness is reduced, and the oil temperature will rise slightly (around 100 degrees). The functions of engine oil are as follows: 1. It lubricates the engine. 2. It provides cooling, cleaning, sealing, rust prevention, and absorbs impact loads.
16
4
Share

How to check your scores for Subject 1 and Subject 2?

After completing the Subject 2 field test, you need to sign your name to confirm your score. Your Subject 2 test score will be listed on the score sheet. If you are unsure of your score, you can inquire with your driving school or instructor. Log in to the official website of the Ministry of Public Security's Internet Traffic Safety Comprehensive Service Management Platform; select your province; click on the personal login option at the top right corner. On the login page, enter the correct login information and verification code, then click login. After logging in, go to the personal main interface and find the student information section. Locate the exam information in the student interface; click on it to view the Subject 2 test information you wish to check.
11
1
Share

How to read the spiral dipstick on a single-cylinder Changchai Hummer circulating water diesel engine?

If the vehicle is in motion, first park the car, turn off the engine, and wait for about 10 minutes to allow the oil to fully return to the oil pan. Pull out the dipstick, wipe off the original oil traces with a clean cloth, and then reinsert the dipstick all the way to the bottom. After a few seconds, pull out the dipstick again to get an accurate oil level reading. There are upper and lower limit marks at the end of the dipstick. Observe the portion wetted by oil—if it falls between the upper and lower limits, the oil level is correct. If the level is above the upper limit, it indicates too much oil; if below the lower limit, it means insufficient oil and requires appropriate topping up.
8
5
Share

What Parts Must Be Replaced in a Flood-Damaged Vehicle?

Engine, transmission, all vehicle fluids, and bearing components. Below is relevant information: 1. Definition of a Flood-Damaged Vehicle: A flood-damaged vehicle refers to a car that has been submerged in water, typically meaning the wiring harness has been soaked, with water immersion depth exceeding one-third of the wheel height, and the vehicle's underbody components have been in prolonged contact with water. Based on the extent of water immersion, it can be classified into three levels. 2. Water-Damaged Vehicle: When the water level exceeds the vehicle's chassis, it is called a water-damaged vehicle. 3. Semi-Flooded Vehicle: When the water level exceeds the oil dipstick, it is termed a semi-flooded vehicle. 4. Fully Flooded Vehicle: When the water level exceeds the engine hood or the dashboard panel, it is called a fully flooded vehicle.
20
0
Share

What to Do If Vehicle Inspection Is Overdue by 10 Days?

If the vehicle inspection is overdue by 10 days, it is necessary to conduct a supplementary inspection as soon as possible. Here is the relevant information about the annual vehicle inspection: 1. Introduction: The annual vehicle inspection refers to a mandatory inspection for every vehicle that has obtained a formal license plate and registration certificate. It is equivalent to an annual physical examination for the vehicle in accordance with the "Technical Conditions for Motor Vehicle Operation Safety." 2. Best Time: Vehicles can apply for the annual inspection within 3 months before the inspection date. It is best to schedule the inspection two months or more in advance, rather than waiting until just a few days before the inspection deadline. Additionally, before the 10th of each month, the workload at inspection stations is relatively light, making it an ideal time to avoid queues. The number of vehicles increases from the middle of the month, and the end of the month is the peak period.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.