···
Log in / Register

How Long Does It Take for Car Carpet Sponge to Dry?

1 Answers
AlexandraLee
09/08/25 7:26am

The sponge under the car usually takes about three days to dry completely. Relevant explanations are as follows: Reason: When the sponge under the car is soaked, the owner can prepare some tools, first remove all the seats of the car, and then place the car in the sun to dry. It is important to try to thoroughly dry the sponge, otherwise it may lead to mold growth later. Additional note: Some parts of a flooded car are not replaced but only dried, and sometimes the internal moisture cannot be completely eliminated. After the vehicle is repaired, all functions return to normal, but some moisture in the circuits may accelerate the oxidation and damage of these wires or circuit boards.

Was this review help?
13
1
Share
More Forum Discussions

Is It Serious for a Parked BMW X5 to Have Water Ingress of Over Ten Centimeters?

If a parked BMW X5 has water ingress of over ten centimeters but the engine is not submerged, it is generally not a serious issue. Steps to handle a flooded car: 1. Immediately cut off the car's power supply. If the car is submerged, powering it on can cause many components to burn out. 2. Shift the car's gear directly to neutral. Do not attempt to forcibly start a water-submerged engine, as this can cause significant damage. 3. Contact a 4S shop or nearby auto repair shop to arrange for a tow truck to take the car for repairs. Methods to deal with water ingress in a car: 1. Disconnect the negative terminal of the battery to prevent short circuits in the car's electrical components due to water. 2. Move the vehicle to a safe location. 3. Check whether water has entered the engine cylinders. 4. Inspect the condition of the fluids in the car's various systems. 5. Clean the fuse box, sensor connectors, and areas where water has accumulated in the car body.
3
5
Share

What is the wading depth of the BMW 5 Series?

The BMW 5 Series is a sedan with a wading depth of 25cm. Generally, the safe wading depth for most vehicles should not exceed half the height of the tires, and the absolute limit is not to exceed the engine air intake. If the air intake is below the water level during wading, water can be sucked into the engine cylinders. Since water cannot be compressed like air, it can cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshaft, etc.). Here are some precautions after driving through water: Orderly passage through flooded areas: If there are multiple vehicles, it's best to pass through the flooded area one by one. When several cars go through water together, the waves created by the leading vehicle can affect the passage of following cars. During wading, avoid shifting gears or accelerating/decelerating in the water. If the engine stalls in the water, do not attempt to restart the vehicle. Disable auto start-stop when wading: Most BMW models are equipped with an auto start-stop system. If driving through water, the vehicle may automatically shut off when braking. After the engine stops, water could enter the engine through the exhaust pipe. Releasing the brake would cause the vehicle to restart automatically, potentially leading to engine damage.
19
5
Share

Can ECO Mode Be Used Frequently?

You can frequently use the ECO mode in your car. ECO mode, also known as economy mode, is particularly effective for fuel savings when driving in congested urban traffic. Under ECO mode, engine carbon buildup is roughly the same as in normal driving mode, so ECO mode can be left on continuously. The main principle of ECO mode is not complicated. It involves comprehensive judgment and analysis of factors affecting fuel consumption during driving, such as automatic transmission gear, engine speed, vehicle speed, braking, and transmission oil temperature. The ECU control unit calculates the optimal fuel amount to supply the engine, effectively reducing fuel consumption compared to normal driving mode. Simply put, it controls engine speed with appropriate gear selection to minimize unnecessary fuel consumption. ECO is an abbreviation, with its Chinese translation representing Ecology (environmental protection), Conservation (energy saving), and Optimization (power). ECO mode is further divided into active ECO driving mode and passive ECO driving mode. When the ECO indicator light on the dashboard illuminates, it indicates that the vehicle's economy mode is activated. ECO mode can be either active or passive. The difference lies in the fact that active ECO mode has a dedicated button, allowing the driver to choose whether to enable it. When the driver presses the ECO mode button, the dashboard indicator light turns on, and the vehicle automatically adjusts settings such as throttle opening, transmission shift logic, and air conditioning output power. Passive ECO mode does not have a dedicated button. When the dashboard ECO indicator light turns on, it serves merely as a reminder. ECO mode automatically evaluates your driving behavior. If your current driving operation achieves the optimal fuel supply, the dashboard will display the ECO indicator light accordingly. Most vehicles use active ECO driving mode, meaning there is a dedicated switch button. Therefore, ECO mode can be enabled during daily driving. However, it is unnecessary to activate ECO mode when driving over 120 km/h, during idling, in N/P gear, or in manual mode—especially when climbing hills. Doing so would not only fail to demonstrate the fuel-saving characteristics of ECO mode but also affect performance. Additionally, ECO mode typically becomes ineffective under the following conditions: When the vehicle speed exceeds 120 km/h, the system prioritizes speed, causing ECO mode to deactivate automatically. During idling or when in N/P gear or manual mode, ECO mode may also become ineffective. When high torque output is required, such as when climbing a hill, the engine control unit prioritizes delivering sufficient power to drive the vehicle, and ECO mode will not function in such scenarios.
3
0
Share

What are the reasons for frequently failing to shift from second gear to third gear?

In the process of shifting from second gear to third gear, the reasons for frequent failure are as follows: 1. Poor coordination between throttle and clutch: During upshifting, the throttle should be released first, then the clutch pedal should be pressed, or both operations can be performed simultaneously. It is essential not to shift while pressing the throttle during the shifting process. If the throttle is not fully released when shifting, it may cause shifting hesitation. 2. The clutch is not fully depressed: Before driving, it is necessary to feel the position and depth of the clutch. If the clutch is not fully depressed when shifting, it will not only cause shifting hesitation but also lead to gear grinding in the transmission. In severe cases, it can directly damage the gears inside the transmission.
10
5
Share

How many tons can a 750 tire bear?

750 tires can bear 10 to 12 tons. Tires are circular elastic rubber products assembled on various vehicles or machinery for ground rolling. They are usually mounted on metal rims to support the vehicle body, cushion external impacts, achieve contact with the road surface, and ensure the vehicle's driving performance. Tires are often used under complex and harsh conditions, enduring various deformations, loads, forces, and high and low temperatures during operation. Therefore, they must possess high load-bearing performance, traction performance, and cushioning performance. Additionally, they are required to have high wear resistance and flex resistance, as well as low rolling resistance and heat generation.
5
1
Share

What is the BMW auto function?

BMW auto refers to the automatic air conditioning function. The following is a related introduction to the BMW auto air conditioning function: Automatic mode: This is the AUTO button. In this mode, once a temperature is set, the air conditioning will automatically activate when the vehicle is started, adjusting the interior temperature to the preset level in the shortest time possible. This is why there are often cases where the air conditioning blows at high intensity immediately after starting the car on hot summer days. In this mode, many mid-to-high-end models also feature automatic defogging functions, where the vehicle can automatically control the system based on fog sensors. Manual mode: On the air conditioning control panel, there are two fan symbols—one large and one small. The large symbol represents increasing the fan speed, while the small one represents decreasing it. To manually turn on the air conditioning, simply press the increase fan speed button.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.