How Long Does Car Window Tinting Last?

What is the reason for the frequent self-cleaning of the Haval H5 diesel?

Haval H5 diesel self-cleaning occurs frequently because the DPF collects too much incomplete carbon smoke, which can cause blockages. The related introduction to diesel engine self-cleaning is as follows: Diesel engine self-cleaning principle: The DPF pressure difference sensor detects excessive exhaust pressure, causing the particles in the DPF to burn and clean. The ECU will then continue post-injection for self-cleaning. Oil for auxiliary self-cleaning: Use ACEA C3 certified oil. During automatic self-cleaning, ensure the RPM is not lower than 2000. When driving normally, maintain the RPM in the green zone to optimize engine combustion.

8

3

Share

What Causes Intermittent Engine Misfiring in Cars?

The reasons for intermittent engine misfiring in cars are: 1. Faults in the ignition system and fuel injection system; 2. Carbon buildup in the engine; 3. Wear and tear of cylinder wires. Engine misfiring refers to the condition where one cylinder fails to operate during engine operation, resulting in severe shaking during acceleration, lack of power, and abnormal noises. Symptoms of engine misfiring include: 1. Significant decrease in power; 2. Shortened lubrication oil usage cycle; 3. Prone to stalling and emitting black smoke. Methods to diagnose engine misfiring are: 1. Observe if the car body shakes violently at idle; 2. Check if there is obvious intermittency in the exhaust pipe airflow; 3. Severe body shaking and lack of power when accelerating below 2000rpm.

9

1

Share

How to Remove the Steering Wheel?

The steps to remove the steering wheel are: 1. Disconnect the battery and turn the steering wheel 90 degrees; 2. Use a flat-head screwdriver to insert from front to back into the hole behind the steering wheel; 3. Insert the screwdriver head between the retaining spring and the airbag hook, adjust the retaining spring strip away from the hook, and the airbag side will automatically pop out toward the seat direction; 4. Turn the steering wheel 180 degrees, remove the airbag and unclip the yellow safety buckle behind the airbag, then pull out the airbag connector to remove the airbag; 5. Pull out the connector of the airbag coupling coil above the inside of the steering wheel, and use an M12 spline to loosen the central fixing bolt of the steering wheel counterclockwise; 6. Remove the steering wheel to complete the process.

12

1

Share

Where is the Roewe RX5 MAX engine produced?

Roewe RX5 MAX engine is produced by SAIC Motor Corporation Limited, so this engine is domestically made. Roewe RX5 MAX uses two types of engines, with model numbers 20L4E and 15C4E. The 20L4E engine has a maximum horsepower of 231 HP, maximum power of 170 kW, maximum power speed of 5300 rpm, and peak torque of 370 N·m. The 15C4E engine has a maximum horsepower of 181 HP, maximum power of 133 kW, maximum power speed of 5600 rpm, and peak torque of 285 N·m. For daily maintenance of the Roewe RX5 MAX engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB_CD grade diesel engine oil should be selected based on mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the engine oil and oil filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through, the filter may burst or the safety valve may open, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while large amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures normal engine operation but also extends the overall lifespan of the radiator and engine.

10

3

Share

How to Determine When to Clean the Throttle Body?

Determining when to clean the throttle body involves observing unstable vehicle acceleration and idle speed. The steps for cleaning the throttle body are: 1. Remove the air filter and intake pipe, unplug the throttle body socket, and take out the throttle body; 2. Spray cleaning agent and wipe the throttle body with a tissue. Precautions for cleaning the throttle body include: 1. It should be disassembled for cleaning; 2. Correct misconceptions about throttle body cleaning; 3. Develop proper driving habits and regular maintenance, avoiding the use of low-quality gasoline. The throttle body is connected to the air filter at the top and the engine block at the bottom, and it is divided into: traditional cable-type and electronic throttle bodies. The working principle of the throttle body is to control the air entering the engine. After the air enters the intake pipe, it mixes with gasoline to form a combustible mixture, which burns to generate power.

15

0

Share

What is the correct way to install a license plate?

The correct way to install a license plate is: 1. Prepare the screw components and screw all the fixing screw components according to the fixing points of the license plate; 2. Align the license plate with the car's fixing points, straighten and align it, insert the screws into the holes, but do not tighten them; 3. Check that the license plate is in the correct position and tighten all the screws; 4. Press the cap onto the spacer to fix it, and the installation is complete. License plates, commonly known as tags, also refer to vehicle license plates, which are plates hung on the front and rear of the vehicle. They are usually made of aluminum, iron, plastic, or paper, and are engraved with the vehicle's registration number, registration area, or other relevant information.

17

5

Share

How Long Does Car Window Tinting Last?

What is the reason for the frequent self-cleaning of the Haval H5 diesel?

What Causes Intermittent Engine Misfiring in Cars?

How to Remove the Steering Wheel?

Where is the Roewe RX5 MAX engine produced?

How to Determine When to Clean the Throttle Body?

What is the correct way to install a license plate?

How to Turn On the Volume of an In-Car Navigation System?

What is the difference between a regular Mini and a Mini JCW?

What is the problem with soft brakes?

Can Toothpaste Remove Car Scratches?