How long after passing the third subject test can you take the fourth subject test at the latest?

1 Answers
FelixFitz
07/30/25 5:32am
It is not calculated based on the time of the third subject test, but on the time of the first subject test. After completing the first subject test for the motor vehicle driver's license, you must complete the other subject tests within three years to obtain the motor vehicle driver's license; otherwise, the previous test results will be canceled. Relevant information about the driver's license test is as follows: 1. Introduction: The driver's test is a qualification examination organized by the Vehicle Management Office of the Public Security Bureau. Only by passing the driver's test can you obtain a driver's license and legally drive a motor vehicle. 2. Content: The motor vehicle driver's test content is divided into the road traffic safety laws, regulations, and related knowledge test subject (also known as the "theoretical test", referred to as "Subject One"), the field driving skills test subject (commonly known as the "stake test", referred to as "Subject Two"), and the road driving skills and safe and civilized driving common sense test subject (commonly known as the "road test", referred to as "Subject Three"). The test content and passing standards are unified nationwide, with corresponding test items specified according to different types of vehicles eligible for driving.
Was this review help?
9
0
Share
More Forum Discussions

What are the two reference points for parallel parking exit?

Parallel parking exit primarily uses two reference points: the right front corner of the hood and the one-third point on the left side of the hood. Below are specific techniques for parallel parking: 1. Adjust the distance between the vehicle body and the parking line: Generally, 30cm is the optimal distance. From the driver's seat, when the parking line aligns with the one-third point of the engine hood, it's approximately 30cm. 2. Steering: When the right rear wheel aligns parallel with the parking line, immediately turn the steering wheel fully to the right. Observe the left rearview mirror; when the inner corner of the parking space appears, immediately straighten the steering wheel. After straightening, continue observing the left rearview mirror. When the left rear wheel touches the parking line, immediately turn the steering wheel fully to the left. Check both side mirrors; when the vehicle body aligns parallel with the parking lines on both sides, straighten the steering wheel.
12
1
Share

How to reset the maintenance light on a Mercedes-Benz GLE320?

The method to reset the maintenance light on a Mercedes-Benz GLE320 is: 1. Enter the total mileage display interface on the dashboard, press and hold the call button on the right side of the steering wheel, while simultaneously pressing the OK button on the left side of the steering wheel for more than 5 seconds. The vehicle computer screen will display engineering data, use the directional keys to adjust various data; 2. The vehicle data displayed includes battery information, voltage and current, engine and chassis information; 3. Select the last item 'AssystPlus' and press the OK key to enter; 4. Choose the full set of maintenance; 5. Press the return key to exit. The maintenance light is a reminder function set by the manufacturer to prompt the owner to perform maintenance at certain mileage or time intervals, displayed in the form of dashboard or screen messages or indicator lights.
12
4
Share

What Causes a Car to Suddenly Stall While Driving Normally

Car suddenly stalling while driving normally can be caused by the following reasons: 1. Electrical circuit failure: Stalling due to low-voltage power interruption during driving, mainly check the ignition and starter switches as well as the fuse box power source. 2. Low-voltage circuit short: Intermittent stalling requires checking the low-voltage circuit. 3. Component failure: Usually caused by faults in the ignition coil, capacitor, or electronic ignition module. 4. Fuel system failure: Such as damage to the fuel pump, fuel pipe rupture, clogged fuel inlet, or empty fuel tank. 5. Ignition system: Issues with the engine overheating anti-explosion system leading to stalling.
14
3
Share

Is the MG6's dual-clutch transmission dry or wet?

The MG6's dual-clutch transmission is dry-type, which offers higher transmission efficiency. Taking the 2020 MG6 as an example, it belongs to the compact car category with body dimensions of: length 4704mm, width 1848mm, height 1466mm, wheelbase of 2715mm, fuel tank capacity of 50 liters, and curb weight of 1300kg. The 2020 MG6 features a MacPherson strut independent front suspension and a multi-link independent rear suspension. It is equipped with a 1.5L turbocharged engine delivering maximum power of 181PS (133kW) and peak torque of 285Nm, paired with a 6-speed manual transmission.
18
4
Share

Why Does the Main Road Vehicle Have the Right of Way Over the Side Road Vehicle?

The main road is designated as such due to its high traffic volume, serving as the arterial route, while the side road functions as the feeder route. Feeder road vehicles must yield to arterial road vehicles. Typically, main roads have more lanes and higher speed limits, hence side road vehicles are required to give way to main road traffic. When traffic pressure on the main road becomes excessive, some vehicles may temporarily use the side roads to alleviate congestion. Interchanges. Relevant information about traffic signals is as follows: 1. Introduction: Traffic signals are devices that regulate traffic flow, generally consisting of red, green, and yellow lights. A red light indicates prohibition of passage, a green light permits passage, and a yellow light serves as a warning. 2. Control Methods: The most basic control method is fixed-time control at individual intersections. Line control and area control can also employ fixed-time methods, referred to as static line control systems and static area control systems respectively.
14
4
Share

Can a Puncture on the Side of a Tire Be Repaired?

Tire sidewall punctures can be repaired depending on the situation: 1. If the puncture area is within 6mm, it can be repaired; 2. If the puncture area exceeds 6mm, there is no need for repair. Tires are circular elastic rubber products installed on various vehicles or machinery, typically mounted on metal rims. They support the vehicle body, cushion external impacts, ensure contact with the road surface, and maintain driving performance, providing load-bearing, traction, and shock-absorbing capabilities. Tire maintenance methods include: 1. Ensuring correct tire pressure; 2. Regularly checking for bulges, cracks, cuts, punctures, and abnormal wear; 3. Inspecting the tire surface for stones, nails, or other hard objects and cleaning them promptly; 4. Minimizing exposure to direct sunlight.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.