How is the TAYRON's transmission?

What are the causes of engine hot piston slap?

The causes of engine hot piston slap are: excessive wear between the piston and cylinder leading to excessive clearance. When the piston connecting rod is twisted or the centerlines of the crankshaft main journal and connecting rod journal are not parallel, the small end of the connecting rod swings back and forth, causing the piston to swing accordingly. As the clearance increases, the swinging piston will also strike the cylinder wall, though this situation is relatively rare. When the clearance between the piston and cylinder wall is appropriate, the piston's expansion coefficient and ovality are within standard, the cylinder has no taper or out-of-roundness, the piston connecting rod is relatively vertical, and the lubrication condition of the engine oil in the hot state is good, the piston will not experience piston slap. During an overhaul, if the non-parallel crankshaft line or twisted connecting rod is not corrected, excessive wear will be aggravated when the clearance in the engine piston connecting rod section is too small. When this wear develops to a certain extent, excessive clearance will occur, and under the drive of the connecting rod, the piston will strike the cylinder wall, producing abnormal noise.

20

5

Share

What does the TC indicator on a Buick mean?

The TC indicator on a Buick stands for Traction Control System, which ensures optimal traction under various driving conditions. If the driver accidentally turns off the traction control switch near the gear shift, the indicator light will illuminate. If the issue persists after confirming it wasn't accidentally pressed, it indicates a malfunction in the traction control system. The Buick LaCrosse measures 5026 mm in length, 1866 mm in width, and 1459 mm in height, with a wheelbase of 2905 mm. It features front-wheel drive, a MacPherson strut front suspension, a multi-link rear suspension, and a unibody construction.

15

5

Share

What is the ON button?

ON means on, and the OFF button means off. ON and OFF are two common buttons found in cars, typically seen on the light control lever, used to turn the car lights on or off. Besides ON and OFF buttons, cars also include SEL, OK, AC, VOL+, VOL-, MUTE, MODE, and SET. The AC button is the compressor button for the car's air conditioning, functioning as the cooling switch, used when operating the air conditioning in summer. VOL+ and VOL- refer to the volume control buttons in the car, which adjust the volume of the car audio. MUTE is the mute button in the car; pressing this button while playing music will instantly mute the sound.

5

0

Share

Which car does the Zotye T700 imitate?

Zotye T700 imitates the Land Rover. Its exterior features a wide grille with a dotted layout, LED headlights as standard across all models. The taillights of the Zotye T700 also use LED sources and are designed with high recognizability. The trunk is equipped with sensors, allowing it to be opened and closed by simply sweeping your foot left or right. The Zotye T700 has body dimensions of 4748mm in length, 1933mm in width, and 1697mm in height, with a wheelbase of 2850mm. It adopts a front-engine, front-wheel-drive layout, with MacPherson strut independent front suspension and multi-link independent rear suspension, built on a unibody structure.

7

2

Share

Under which brand does the Warrior belong?

The Warrior is a vehicle under the BAIC (Beijing Automotive Industry Holding Co.) brand, categorized as a rugged off-road vehicle. The entire lineup is equipped with a 1.5-liter turbocharged engine, delivering 136 horsepower and 200 Newton-meters of torque. The maximum power output is achieved between 2,000 and 4,400 RPM, while the peak torque is available from 2,000 to 4,500 RPM. This engine features multi-point electronic fuel injection technology and is paired with a 5-speed manual transmission. The Warrior utilizes leaf spring non-independent suspension for both front and rear axles and comes with a part-time four-wheel-drive system, employing a body-on-frame construction. The vehicle's dimensions are 4,080 mm in length, 1,828 mm in width, and 1,870 mm in height, with a wheelbase of 2,300 mm.

7

0

Share

What does the R gear mean when driving?

The R gear is the reverse gear. The car can only be shifted into the R gear after coming to a complete stop and pressing the brake pedal. P is the parking gear, specifically used when parking an automatic transmission vehicle. When shifted into P gear, there is no power transmission, and the locking mechanism inside the transmission locks the power output shaft, preventing the vehicle from moving. Forcing movement in this state can damage the transmission, so towing requires lifting the drive wheels off the ground. N is the neutral gear, functioning on the same principle as the neutral gear in a manual transmission, and is used for brief stops. D is the drive gear, also known as the forward gear, which is the gear used when driving. When shifted into this gear, the driver's task is to control the accelerator and brake pedals—pressing the accelerator to accelerate and the brake to decelerate.

9

2

Share

How is the TAYRON's transmission?

What are the causes of engine hot piston slap?

What does the TC indicator on a Buick mean?

What is the ON button?

Which car does the Zotye T700 imitate?

Under which brand does the Warrior belong?

What does the R gear mean when driving?

Will the valves make a ticking sound after replacing the cylinder head gasket?

What is the shelf life of opened engine oil?

What does it mean when the new engine malfunction indicator light comes on?

What are the steps for parking a manual transmission car?