How is the fuel consumption per 100 kilometers calculated for sedans?

1 Answers
LaStephanie
07/29/25 7:03pm
Sedan fuel consumption per 100 kilometers = Volume of fuel (liters) ÷ Distance the car can travel with that fuel (kilometers) × 100. Methods to reduce fuel consumption and influencing factors are introduced as follows: Methods to reduce fuel consumption: You can add fuel additives to the fuel tank to improve combustion and remove carbon deposits. It is recommended to regularly inspect and maintain the vehicle, clean or replace the three filters, which will reduce fuel consumption. At the same time, the longer the idling time when parked, the greater the fuel consumption, so try to minimize idling time; and avoid sudden acceleration, stepping hard on the accelerator, and driving at low RPMs. Factors affecting fuel consumption: Various working conditions such as acceleration, deceleration, braking, and engine idling, as well as load capacity, temperature, and whether the air conditioning is on, will all affect the car's fuel consumption.
Was this review help?
1
2
Share
More Forum Discussions

What Causes Car Oil Leaks?

Below are the reasons for car oil leaks: 1. Incorrect oil viscosity: Oil leaks that occur after an oil change are often due to the newly replaced oil being too thin and not meeting the original vehicle's standard specifications, causing leaks from the engine oil pan. 2. Overfilling of oil: If the engine oil pan and other components are normal but leaks still occur, it is often due to overfilling of oil. 3. Loose drain plug: This is commonly caused by frequent driving on rough roads. The drain plug gasket should also be replaced regularly according to the maintenance schedule. 4. Aging gasket: Localized leaks from the oil pan gasket are caused by aging or poor-quality gaskets. The oil pan gasket needs to be replaced, or the leaking area should be sealed with adhesive.
11
3
Share

How Does Iron Contamination Form on Cars?

Due to the porous nature of automotive paint surfaces, prolonged exposure to air causes the adhesion of various contaminants, primarily oxides, which constitute the main components of iron contamination. Below is relevant information on removing iron contamination: 1. Product-based removal: Use automotive detailing clay for intensive cleaning. If ineffective, employ specialized iron particle removers through soaking processes - though the complete removal procedure is time-consuming. For severe cases, polishing remains the ultimate solution. 2. Glazing and coating: Vehicles with softer paint surfaces may develop micro-scratches from windblown sand particles during high-speed driving. For such automobiles, paint glazing creates a durable mesh-like protective film that enhances paint hardness, with effects lasting approximately one year. Coating treatments achieve similar protective results.
14
0
Share

What Causes the Ticking Sound in a Car?

The possible causes of abnormal sounds in a car are as follows: 1. Valve noise: After starting the engine, you may hear a "ticking" sound, which is the sound of the valves. This is especially noticeable when the engine is cold, as the oil pressure hasn't built up yet and the valves aren't properly lubricated. The sound should disappear after a short while. 2. Insufficient lubrication: Generally, when a car is cold-started, the engine sound may be slightly louder than when it's warm. As long as the sound is even and smooth, not harsh, it's usually not a problem. This is because when the engine is cold, the gap between the cylinder wall and the piston hasn't reached the optimal size, and the oil lubrication isn't fully effective. Normally, when the engine block temperature reaches about 95 degrees, the sound will return to normal. 3. Oil-related issues: Poor-quality oil, not changing the oil for a long time, or low oil levels can all increase friction between the valves and guides, as well as in components like hydraulic lifters, making various sounds in the engine louder.
11
0
Share

What is the ground clearance of the TACQUA?

The minimum ground clearance of the FAW-Volkswagen TACQUA, a compact SUV, is 196mm. Here are some details about minimum ground clearance: 1. Definition: Minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. It is used to indicate the vehicle's ability to pass over obstacles such as rocks and stumps without collision. 2. Impact on driving: The greater the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven ground, but the higher the center of gravity, which reduces stability. Conversely, the smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven ground, but the lower the center of gravity, which can increase stability.
13
4
Share

Why does the Sagitar make noise when turning at low speed?

The reasons for the Sagitar making noise when turning at low speed are as follows: 1. Turn signal reset sound: When turning on the turn signal while steering, it may be caused by the rebound clip of the turn signal auto-reset mechanism, which is normal. 2. Sound from the steering column dust cover: If the noise comes from below the steering wheel, it may be from the steering column dust cover. Lack of lubrication in the dust cover can cause friction noise. Applying some grease inside the dust cover can resolve this. 3. Noise from the steering wheel: This could be due to the airbag clock spring inside the steering wheel. Removing the steering wheel and applying grease to the airbag clock spring can fix it. Note: Disconnect the airbag fuse before removing the steering wheel to prevent the airbag from deploying. 4. Noise from the stabilizer bar: Check if the stabilizer bar bushings are loose or damaged. Loose or damaged stabilizer bar bushings can cause noise not only when turning but also when driving on uneven roads. Loose stabilizer bar bushings can be fixed by adding shims.
6
5
Share

Is Dual Clutch an Automatic Transmission?

Dual clutch is an automatic transmission. The dual clutch transmission, abbreviated as DCT, differs from conventional automatic transmission systems. It is based on a manual transmission yet belongs to the category of automatic transmissions. In addition to offering the flexibility of a manual transmission and the comfort of an automatic transmission, it also provides uninterrupted power output. Simply put, a dual clutch system employs two sets of clutches working simultaneously—one managing the odd-numbered gears and the other handling the even-numbered gears. This design aims to eliminate the power interruption issue during gear shifts in traditional manual transmissions, thereby achieving rapid gear changes. Currently, common dual clutch transmissions include Volkswagen's DSG, Ford's PowerShift, Mitsubishi's SST, and Porsche's PDK.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.