How is hit-and-run for vehicle scratches punished?

1 Answers
LukeFitz
07/29/25 9:01pm
In the case of a hit-and-run scratch accident, once confirmed by police investigation, it will be uniformly treated as a traffic accident hit-and-run, with the perpetrator bearing full responsibility for the accident. As for punishment, it may result in a one-time deduction of 12 points or direct revocation of the driver's license. If the perpetrator voluntarily surrenders and reaches a satisfactory settlement with the other party, the police may choose not to file a case.
Was this review help?
14
2
Share
More Forum Discussions

How to Set the Locking Sound for BMW 525?

BMW 525 belongs to the BMW 5 Series, with a top speed of 250km/h. The vehicle weight is 1740KG, and it has 24 valves. Before setting the locking sound, it is necessary to fully understand the relevant information about the BMW 525. First, click on the vehicle's central control screen and select "My Vehicle." Alternatively, enter the interface, check the "Lock on Walk Away" option, and the locking sound setting will be completed.
19
0
Share

How to Remove the Steering Wheel of a Buick LaCrosse?

The tools required for removal include a flat-head screwdriver and a hex key tool. When prying to a certain extent, use your hand to lift upwards. Since fingers are more flexible and easier to control the force, there is no need to remove the airbag. The area that needs to be removed is the region circled by the black line in the diagram. The components in this area must be completely removed. Once removed, the steering wheel can be successfully taken off.
17
3
Share

How to Open the Hood of a BMW 3 Series?

Before opening the vehicle's hood, ensure the car is parked and the engine is turned off. Inside the driver's cabin, you can find the hood release lever located on the left side near the driver's footwell. The BMW 3 Series is a new generation sedan product from BMW Group, with a body weight of 1465 kilograms, equipped with a 4-cylinder gasoline engine. There is a symbol indicating the front hood, and the "X2" on it means you need to pull it twice. During the operation, it is important to correctly use the various buttons in the car.
14
2
Share

What causes the ABS light to illuminate in the new Santana?

There are multiple states of the ABS light being on, and the causes and solutions vary depending on the state, as detailed below: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by mud, sludge, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and the wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections between system wires or poor contact of the ABS relay, leading to system failure. Solution: Check the wire connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, and the ABS light turns off. The ABS system power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and verify the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact of the ABS hydraulic valve body; poor electrical connector contact of the ABS hydraulic valve body; ABS computer malfunction. Solution: Loosen and then retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary. Check if the connector gap has widened. Replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals. Incorrect tire or wheel rim specifications may also be a factor. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact of the brake light. Solution: With the engine running, press the brake pedal and push the brake switch linkage down fully with your fingers. Release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary. If the ABS warning light is on, it is advisable not to continue driving. An illuminated ABS light indicates a fault in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks.
6
5
Share

How to Check the Location of Your Ordered Mercedes-Benz Car?

When purchasing a car, there will usually be staff members to sign the contract with you, or you can directly call the 4S store to inquire with the staff. In addition to making phone inquiries, you can also check the progress of your car order by using the order number on the official website of the vehicle you ordered. Mercedes-Benz has its own official website. Mercedes-Benz cars are known for their high technical standards, quality benchmarks, and strong innovation capabilities for continuous improvement.
10
1
Share

How to Set the Key to Close Windows on Buick Verano?

This is a hidden feature of the vehicle. Simply press the lock button on the remote control, and all four windows of the vehicle will automatically rise until fully closed. Step on the brake pedal of the Buick Verano. Turn the key of the Buick Verano to the ON position. The dashboard of the Buick Verano will light up, and the vehicle's power will be fully activated. Pull the window regulator of the Buick Verano up to the highest point. Press and hold the door lock button of the Buick Verano for 10 seconds to complete the setup.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.