How Heavy is a Motorcycle?

How to Repair Severe Body Rust?

Use a grinder to sand the rusted area, spray some expanding foam, trim off excess foam, wipe clean, and apply a layer of rust inhibitor. Cut a piece of fiberglass mesh, mix resin adhesive with hardener, and apply with a brush. After the adhesive dries, use a grinder to smooth the edges. After sanding, apply body filler, sand with sandpaper, and proceed with painting.

2

Share

What to Do When the Wiper Doesn't Reset?

If the wiper cannot automatically reset, it may be due to aging wiper blades or dust and other debris stuck between the blades and the windshield, obstructing the wiper's reset. You can clean the wiper blades and windshield with a damp cloth, and replace the wiper or blades if necessary. It could also be caused by wiring issues, motor failure, or wiper switch malfunction, in which case it is recommended to visit an auto repair shop. Below are some maintenance tips for wipers: 1. Avoid oil contamination: If oil stains get on the windshield or wipers, they won't clean rainwater effectively. Although wipers rest on the windshield, they are often overlooked during routine maintenance. If you notice oil stains on the glass, use a glass cleaner to wipe the wiper blades and windshield when washing the car. 2. Keep in the lowest position when not in use: When not in use, the wipers should be placed in the lowest position, and the lower part of the windshield should be cleaned regularly to prevent debris from causing long-term pressure and deformation of the wiper blades. 3. Don't forget the wiper blades when washing the car: Although wipers rest on the windshield, they are often neglected during maintenance until problems arise during use. Maintaining wiper blades is actually very simple. Every time you wash the car, in addition to cleaning the windows, it's best to wipe the wiper blades with a glass cleaner to extend their lifespan.

19

5

Share

How to Maintain a Turbocharged Car?

Maintaining a turbocharger requires regular replacement and cleaning of engine oil, filters, air filters, etc., to reduce impurities and prevent excessive wear of the turbocharger's blades. Therefore, it is essential to invest in replacing the oil filter, air filter, and engine oil to keep the car in good working condition and extend its service life. The following are the methods to deal with abnormal noises from the turbocharger: 1. First, check whether the turbocharger is damaged. If the turbocharger is not damaged, confirm whether there is oil leakage in the intake and exhaust pipelines or the intercooler. Check the clamps on the intake pipeline and use soapy water to inspect for cracks. 2. Check for air leakage at the joint surfaces between the turbocharger and the engine exhaust manifold, as well as between the turbocharger and the exhaust pipe. Inspect whether the bypass valve diaphragm of the turbocharger is ruptured. If it is ruptured, it may be accompanied by insufficient power. 3. If there is no air leakage in the pipeline connections, inspect the internal flow channels of the turbocharger. Check whether there are burrs or protrusions on the inner wall of the housing, whether the impeller is fouled, or whether the diffuser section is fouled. Diagnosing abnormal noises from the turbocharger is a systematic task, and it is recommended to have it checked at a repair shop.

1

Share

Does entering the left-turn waiting zone count as running a red light?

Entering the left-turn waiting zone does not count as running a red light. If you have already crossed the stop line and are continuing to turn left when the red light comes on, it is not considered running a red light. More details are as follows: 1. When the straight-through signal in the same direction turns green, vehicles in the left-turn lane must move forward into the waiting zone and wait for the signal. The 'left-turn waiting zone' is only for left-turning vehicles. When the straight-through signal in the same direction is green, even if the left-turn signal is red, left-turning vehicles are allowed to enter the 'left-turn waiting zone' at the intersection and wait until the left-turn signal turns green before proceeding. 2. It should be reminded to drivers that the left-turn waiting line is not a 'stop line.' If both the straight-through and left-turn signals are red, all vehicles must wait at the previous stop line. 3. If a vehicle has just crossed the stop line when the light is red but stops immediately, this will not be penalized as running a red light. However, if there is obvious movement after crossing the line, it will be penalized. 4. The three photos taken by electronic monitoring for running a red light are: the vehicle crossing the stop line, followed by two photos of the vehicle reaching the middle of the intersection and the opposite side of the intersection.

7

4

Share

How Many Factories Does BMW Brilliance Have?

BMW Brilliance has 2 factories, one is the Tiexi Plant and the other is the Dadong Plant, both located in Shenyang. The expansion projects for BMW Brilliance's new Tiexi Plant and Dadong Plant are currently underway. BMW Brilliance Automotive Ltd. was established in May 2003 as a joint venture between BMW Group and Brilliance Group. Its business scope includes the production of BMW and passenger vehicles (including sedans, station wagons, off-road passenger vehicles/multi-purpose sports vehicles, multi-purpose passenger vehicles/sports tourers, and new energy vehicles) along with their engines, power batteries, components, accessories, and production equipment; sales and leasing of self-produced products; after-sales services for its products (including providing spare parts and maintenance); research and development and technology transfer related to automotive technology and power batteries; import and export of various goods and technologies (excluding those restricted or prohibited by the state); wholesale and retail of used cars, automotive and motorcycle parts (including spare parts), accessories, car accessories, and BMW lifestyle products. BMW Brilliance's lineup includes models such as the BMW X2, BMW 3 Series, BMW X3, BMW 5 Series New Energy, BMW 1 Series, BMW X1, BMW 5 Series, BMW iX3, and BMW X1 New Energy.

18

5

Share

How to Repair Car Tarpaulin?

Cut a piece of tarpaulin larger than the hole, clean the dust from the damaged area and the cut tarpaulin piece with a wire brush, apply universal adhesive to both surfaces, and hammer them tightly together when the adhesive is almost dry. After thoroughly cleaning and drying the entire tarpaulin, mix ox paste, paraffin wax, green blended paint, and varnish, heat the mixture until melted, then add water and stir into a thick paste. Apply 2-3 coats and dry in the sun.

19

1

Share

How Heavy is a Motorcycle?

How to Repair Severe Body Rust?

What to Do When the Wiper Doesn't Reset?

How to Maintain a Turbocharged Car?

Does entering the left-turn waiting zone count as running a red light?

How Many Factories Does BMW Brilliance Have?

How to Repair Car Tarpaulin?

What is the correct way to operate a car steering wheel?

Advantages and Disadvantages of Front-Wheel Drive and Rear-Wheel Drive?

Symptoms of a Faulty Turbocharger?

What to Do About a Cracked Car Windshield?