How far should the front of the car be from the wall to avoid hitting it when turning the steering wheel to the full lock?

1 Answers
Elliot
07/24/25 3:43am
As for the question of how far the front of the car should be from the wall to avoid hitting it when turning the steering wheel to the full lock, it actually depends on the length of the vehicle and the timing of turning the wheel. If the car is longer, the distance from the wall should be greater. Similarly, if the steering is turned earlier, the car should also be farther from the wall. Therefore, there is no fixed value for this distance. Additional information is as follows: 1. Technique: You can treat the inner corner as the wall corner. Before entering the curve, first drive close to the right side of the lane, aligning the right 1/3 of the car hood with the right edge of the road, ensuring the right side of the car is about 30 cm from the edge. When the left rearview mirror is parallel to the inner corner, you can turn the steering wheel fully to the left. At this point, the car will not hit the inner corner, meaning it won't hit the wall corner. 2. Vehicle condition: In reality, the width of the road is wider than that in the driving test (Subject Two), so following the Subject Two method ensures you won't scrape the wall corner in real situations. If turning the steering wheel fully to the left, always monitor the front of the car and the rearview mirror, constantly checking the condition of the left side of the car. Slow down or even stop if necessary. Similarly, if turning the steering wheel fully to the right, observe the right front of the car and the right rearview mirror, and check through the rear window if needed.
Was this review help?
7
3
Share
More Forum Discussions

How to Install Car Snow Chains?

The installation steps for car snow chains are: 1. Lift one side of the vehicle's drive wheel with a jack, unfold the rubber snow chain and lay it flat under the wheel; 2. Pull both ends of the snow chain up to meet at the top of the wheel, so that the snow chain wraps around the wheel; 3. Hook the inner side of the wheel with the snow chain hook; 4. Pull the outer side of the snow chain mesh outward by hand and then hook the outer hook; 5. Take out the rubber edge rope and hook the hooks to both ends of the snow chain; 6. Install the thinner edge rope from the diagonal direction to ensure that the tension of the rubber rope is evenly distributed; 7. Install the medium and thicker edge ropes according to the above method.
11
5
Share

What are the control methods of automotive circuits?

Automotive circuit control methods include: 1. Power circuit: Also known as the charging circuit, it consists of the battery, generator, regulator, and charging indicator device; 2. Starting circuit: Composed of the starter, relay, starting switch, and starting protection circuit; 3. Lighting and light signal device circuit: Includes headlights, fog lights, position lights, turn signals, brake lights, reverse lights, interior lights, and related control relays and switches; 4. Ignition circuit: Consists of the ignition coil, distributor, electronic ignition controller, spark plugs, and ignition switch; 5. Instrument information system circuit: Composed of instruments and their sensors, various warning indicators, and controllers; 6. Electronic control system circuit: Includes the engine control system, automatic transmission and constant speed control system, anti-lock braking system, and airbag control system.
5
3
Share

What are the reasons for no response from motorcycle electric ignition?

Reasons for no response from motorcycle electric ignition: 1. The clutch switch is in the closed state; 2. Insufficient battery power; 3. Excessive spark plug gap or too much carbon deposit; 4. Faulty high-voltage cap connected to the spark plug; 5. Damaged starter fuse; 6. Disconnected wiring. Solutions for no response from motorcycle electric ignition: 1. Check whether the cylinder pressure is normal. If the cylinder has no compression ratio, it may be that the valve is bent and cannot close tightly, resulting in no pressure and inability to start; 2. Check whether the spark plug has sufficiently strong high-voltage electricity, whether the gasoline in the carburetor is normal, whether the carburetor is blocked, whether the intake pipe has air leakage, and whether the air filter and exhaust pipe are blocked. It is recommended to clean the relevant parts.
17
4
Share

Should the Emgrand GS use 5w30 or 5w40?

The Emgrand GS uses 5w30 fully synthetic engine oil. Engine Oil: Engine oil is an item that every car owner will come into contact with during the vehicle usage process. It is known as the blood of the engine. If there is no engine oil inside the engine, the engine cannot operate normally. Functions: Engine oil not only lubricates the engine but also serves to clean, seal, buffer, prevent rust, and dissipate heat. The choice of engine oil should be based on the engine's requirements and the driver's usual driving habits. It is unnecessary to use overly advanced oil in an engine with lower requirements, nor should lower-grade oil be used in an engine with higher requirements.
6
2
Share

Is Beijing Benz Produced by BAIC?

Beijing Benz is not produced by BAIC. Beijing Benz vehicles are manufactured in a joint venture factory established by Beijing Automotive Group Co., Ltd. and Daimler AG. 2021 Mercedes-Benz E-Class: The dimensions of this vehicle are 5078mm in length, 1860mm in width, and 1484mm in height, with a wheelbase of 3079mm. It is classified as a mid-to-large-sized car and is equipped with a 9-speed automatic transmission. The top speed of the 2021 Mercedes-Benz E-Class is 230 km/h, with a body structure of a 4-door, 5-seat sedan and a fuel tank capacity of 66L. Power: The 2021 Mercedes-Benz E-Class has a maximum horsepower of 184 hp, a maximum torque of 280 Nm, a maximum power speed range of 5800 to 6100 rpm, and a maximum power output of 135 kW. Both the front and rear suspensions are multi-link independent suspensions.
3
4
Share

What Causes the Brake Light to Stay On? How to Fix It?

The reasons and solutions for the brake light staying on are as follows: 1. Check if the brake pads are worn to the limit and replace them in time; 2. The brake light switch can be adjusted—remove, adjust, and reinstall the switch; 3. The brake switch is faulty—the switch is installed above the brake pedal, so repair or replace the switch; 4. Check if the brake fluid is low and top it up in time; 5. Inspect the brake bulb for damage—the brake light is usually installed at the rear of the vehicle, with a red-colored body to enhance light penetration. This ensures that vehicles behind can easily detect braking even in low visibility conditions, helping to prevent rear-end collisions. In simple vehicle models, power flows through a fuse to the brake switch. When the brake pedal is pressed, the switch connects, sending electricity to the two brake lights and the high-mounted brake light, completing the circuit via the negative line connected to the vehicle body.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.