How Far Can a Mercedes Run After the Low Fuel Warning?

Will points be deducted for changing lanes by crossing the diversion line?

Points will be deducted for changing lanes by crossing the diversion line. Below are the specific details: Introduction to diversion lines: Diversion lines are prohibited markings used to indicate that vehicles must follow the prescribed route and are not allowed to cross or drive over the lines. If a vehicle crosses or drives over the diversion line, the police may impose penalties such as "a warning and 3 points deducted" or "a fine and 3 points deducted" on the driver. Purpose of diversion lines: The purpose of diversion lines is to ensure that every vehicle can "stay in its lane," serving to regulate, guide, and warn traffic, thereby reducing traffic accidents. Use of diversion lines: Diversion lines are mainly used at intersections that are too wide, irregular, or have complex driving conditions, at ramp entrances of interchanges, or at other special locations.

5

4

Share

Should You Press the Clutch or the Accelerator When Reversing?

Press the clutch when reversing. Here are the details: Reversing on flat ground: The car does not require much power to reverse. Simply pressing the clutch to engage the semi-engagement point and using the brake is sufficient for control. Reversing on a slope: When the clutch alone cannot provide enough power, lightly pressing the accelerator can supplement the required power. Here is additional information: Clutch: The clutch is located inside the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch serves as the input shaft of the transmission. Function of the clutch: The clutch is a common component in mechanical transmissions, allowing the drivetrain to be engaged or disengaged as needed.

15

0

Share

What to Press When Reversing?

Press the clutch when reversing. Here are the specific details: Reversing Process: When reversing, first press the clutch pedal to disengage the clutch, which cuts off the power connection between the engine and the transmission. Then, shift into reverse gear and slowly release the clutch pedal until the car starts moving gradually. Reversing Technique: You can also use the semi-engaged state (half-clutch) when reversing. Just slowly lift the clutch pedal until the vehicle overcomes the resistance and starts moving, then hold the pedal at that position. Reversing Precautions: Always check the rear surroundings before reversing. Do not rely too much on electronic reversing aids, and ensure it is safe before proceeding.

1

3

Share

What are the reasons for the sudden stiffness and inability to press the brake when reversing?

Here are the reasons for the sudden stiffness and inability to press the brake when reversing: Reason: One is a problem with the vacuum booster pump, making it difficult to press the brake without assistance. Another situation is that after the engine is turned off, the brake is pressed again, depleting the vacuum created by the vacuum booster pump, and subsequent braking relies solely on manual force. Related introduction to brakes: The brake is a mechanical braking device that can slow down the vehicle speed. Simply put: The car brake pedal is located under the steering wheel. Pressing the brake pedal causes the brake lever linkage to be pressurized and transmitted to the brake pads on the brake drum, clamping the brake disc to slow down or stop the car. The manual brake in a car is located next to the gear shift, connected to the brake lever.

10

2

Share

What does a guide lane line mean?

Guide lane lines are directional lane markings used to indicate the direction vehicles should follow when entering an intersection. These markings are typically painted at busy traffic intersections to clearly define driving directions, ensure orderly traffic flow, and alleviate congestion. Types and functions of guide lane lines: Guide lane lines are marked on the road surface of each lane and can be categorized into variable and fixed types. They usually appear at high-traffic intersections to guide vehicle direction, maintain orderly traffic flow, and reduce congestion. Fixed guide lane lines include straight lanes, left-turn lanes, and right-turn lanes, while variable guide lane lines include combined left-turn and U-turn lanes, combined right-turn and straight lanes, and tidal flow lanes. Rules for driving in variable guide lanes: Variable lanes are typically set as combined left-turn and U-turn lanes or combined right-turn and straight lanes. If the current lane direction is unclear, drivers can follow the flow of traffic. For example, if there are fewer left-turning vehicles than straight-moving vehicles, the variable lane may be designated for straight movement. For tidal flow lanes, drivers must follow the directional signs based on the time of day. For instance, during morning rush hours, the variable lane may be for straight movement, while during evening rush hours, it may switch to left turns. If a variable guide lane has no directional indicators or markings, drivers may change lanes to the left or right as needed.

17

4

Share

What is the difference between guide lines and channelizing lines?

The purpose of setting channelizing lines is to ensure that every vehicle can "follow its lane", playing a role in regulating, guiding, and warning traffic, thereby reducing traffic accidents. Guide lines are set at the entrance section of intersections as lane demarcation lines, called guide lines, used to indicate the position of guide lanes where vehicles should drive according to the guiding direction. Channelizing lines: The form of channelizing lines mainly consists of one or several white V-shaped lines or diagonal line areas set according to the terrain of the intersection, indicating that vehicles must drive along the prescribed route and must not cross or drive over the lines. They are mainly used at overly wide, irregular, or complex intersections, ramp entrances of interchanges, or other special locations. Guide lines: Guide lines are set at the entrance section of intersections as lane demarcation lines, called guide lines, used to indicate the position of guide lanes where vehicles should drive according to the guiding direction; such markings are generally painted at intersections with heavy traffic to clarify the direction of travel, ensure each vehicle follows its lane, and alleviate traffic pressure.

18

1

Share

How Far Can a Mercedes Run After the Low Fuel Warning?

Will points be deducted for changing lanes by crossing the diversion line?

Should You Press the Clutch or the Accelerator When Reversing?

What to Press When Reversing?

What are the reasons for the sudden stiffness and inability to press the brake when reversing?

What does a guide lane line mean?

What is the difference between guide lines and channelizing lines?

What to Do If the Gear Suddenly Becomes Loose and Can't Engage?

What does gear mismatch mean?

Does a higher gear mean faster speed?

What car has an inverted H logo?