How Early Should You Schedule the Subject 4 Exam?

How to Fold Down the Rear Seats of the Teana?

The rear seats of the Teana cannot be folded down. Below is an introduction to the rear seats of the Teana: Rear seat folding methods include proportional folding and full folding. The correct steps to adjust car seats are: 1. Adjust to a suitable sitting position; 2. Adjust the seat height; 3. Adjust the backrest angle; 4. Adjust the seat distance. The dimensions of the Teana are 4901mm in length, 1850mm in width, and 1450mm in height, with a wheelbase of 2825mm. It is equipped with a CVT continuously variable transmission. The car has a top speed of 197 km/h, a fuel tank capacity of 61.3L, a maximum horsepower of 156, and a front-wheel drive system.

18

3

Share

How to Replace a Mercedes Car Key?

Mercedes car keys can be replaced at 4S stores or auto parts markets. More details about car key replacement are as follows: 1. Most car keys are equipped with electronic chip anti-theft technology, using two-way communication between the key and the vehicle. When the key ID verification is successful, the CAN communication sends a signal to the BCM to allow engine start-up. Only keys with registered ID codes in the BCM and ECM can start the engine. 2. 4S stores use specialized diagnostic computers and software to register keys. After initializing the ignition key, the key ID code is registered step by step. Auto parts markets may use password decryption methods to match keys, which has lower security. 3. For vehicles with smart keys, simply re-register the key. For mechanical keys with chips, 4S stores need to replace the steering lock to register the key and recommend replacing all mechanical lock cylinders in the vehicle.

7

4

Share

Do China VI new cars still need a break-in period?

China VI new cars still require a break-in period. Here is relevant knowledge about new car break-in: 1. China VI is merely a national emission standard for testing pollutant levels in exhaust gases, which has no direct relationship with the break-in period. Therefore, any new car still needs to undergo proper break-in. 2. In the past, due to less advanced automotive manufacturing processes, produced components were relatively rough and did not fit together perfectly when installed in vehicles, necessitating a break-in period for these parts to adapt to each other. 3. Today's automotive industry can utilize industrial robots and automated programming to manufacture more precise and durable automotive components that can operate smoothly immediately after installation. Although modern vehicles have lower break-in requirements, this doesn't mean they don't need any break-in at all.

13

4

Share

How many times can the Subject 1 test be scheduled at once?

You can schedule up to three times for the Subject 1 test at once. Here is some information about scheduling the Subject 1 test: 1. Scheduling rules: For the C1 driver's license Subject 1 test, you have five opportunities to retake the test. Each retake requires paying a retake fee and rescheduling. 2. Regulations: According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses": Article 37 states that each subject test can be taken once, and if the test is failed, it can be retaken once. If you do not take the retest or fail the retest, the current test session is terminated, and the applicant must reschedule the test. However, Subject 2 and Subject 3 tests must be scheduled at least ten days later. If the Subject 3 safety and civilized driving knowledge test is failed, the passed road driving skills test results remain valid.

14

4

Share

What are the body dimensions of the Fengjun 7?

Fengjun 7 has a length, width, and height of 5395mm/1800mm/1760mm, which are official data. The length of Fengjun 7 refers to the distance between two vertical lines perpendicular to the vehicle's longitudinal symmetry plane and touching the outermost protruding parts at the front and rear of the car. The width refers to the distance between two planes parallel to the vehicle's longitudinal symmetry plane and touching the outermost rigid fixed protruding parts on both sides of the vehicle. The height refers to the distance between the highest point of the vehicle and the supporting plane of the vehicle. The turbocharged engine of Fengjun 7 has a maximum power of 115kw and a maximum torque of 345 Nm. The maximum power speed of this engine is 3600 rpm, and the maximum torque speed is 1400-2800 rpm. It is equipped with direct injection technology and uses an aluminum alloy cylinder head and cast iron cylinder block. This engine is matched with a manual transmission (MT). There are national regulations regarding the dimensions of vehicles. According to the national standard "GB1589-89," the total width of a vehicle does not include rearview mirrors. The limitation on vehicle width is to provide sufficient lateral clearance for overtaking between adjacent lanes. This means that in the national standard, the significance of vehicle width data is to ensure enough space during overtaking, preventing accidents due to excessive width or situations where road markings are narrower than the vehicle's width. Additionally, national regulations stipulate that the total width of a vehicle must not exceed 2.5m to meet the usage requirements of public roads.

7

5

Share

What are the reasons for shifting into the wrong gear in Subject 3?

Incorrect hand positioning or nervousness can both lead to shifting into the wrong gear in Subject 3. Below is an introduction to the techniques for gear shifting in Subject 3: 1. Starting gear control: The starting gear should be in first gear. Whenever the vehicle moves from a standstill to starting, the gear should remain in first. 2. Sequential gear shifting: The road test strictly prohibits skipping gears. Gear changes must be sequential, such as first to second gear, second to third gear, and so on. Otherwise, the test recorder will log it and deduct corresponding points. If you accidentally shift into the wrong gear, you can press the clutch immediately to shift back to the correct gear and then re-shift. 3. Speed is crucial: The key point of gear shifting is speed—completing the actions of pressing the clutch, shifting gears, and pressing the accelerator as quickly as possible. 4. Stable shifting: Gear shifting must be steady. When shifting, the clutch must be fully depressed, and gear changes should only occur within a certain speed range.

10

3

Share

How Early Should You Schedule the Subject 4 Exam?

How to Fold Down the Rear Seats of the Teana?

How to Replace a Mercedes Car Key?

Do China VI new cars still need a break-in period?

How many times can the Subject 1 test be scheduled at once?

What are the body dimensions of the Fengjun 7?

What are the reasons for shifting into the wrong gear in Subject 3?

What are the reasons for the parking brake system failure causing the car not to start?

What does the STOP fault code mean?

Does windshield washer fluid have an expiration date?

What is the fuel tank capacity of the Tiguan?