How Can Beginners Determine Tire Position?

1 Answers
MacAlan
07/29/25 1:05pm
Methods for beginners to determine tire position: 1. The wheel centerline is the distance between two perpendicular lines passing through the midpoint of two adjacent wheels on the same side of the vehicle and perpendicular to the vehicle's longitudinal symmetry plane; 2. When the driver looks straight ahead in a proper sitting posture, if the junction point between the left wiper and the car body coincides with the junction point between the left lane marking and the car hood, the left tire has already rolled over the lane marking; 3. Since the position and size of wipers vary for each car, the so-called junction point is not uniform. When the distance between the left lane marking and the car hood junction point is about 20cm from the left A-pillar, the left tire should have already or is about to roll over the line.
Was this review help?
3
2
Share
More Forum Discussions

What Causes the CVT Light to Illuminate?

The reasons for the CVT light illuminating are as follows: 1. Exhaust emissions not meeting standards: Issues such as poor fuel quality, failure of the catalytic converter, excessive carbon buildup in the intake manifold, clogged fuel injectors, malfunctioning oxygen sensors, or occasional engine misfires can all cause the engine warning light to illuminate. Among these, poor fuel quality leading to the engine warning light is the most common. 2. Poor engine system performance: The engine warning light may illuminate due to poor performance in the engine system, such as faults in the throttle pedal sensor, throttle position sensor, air flow meter, crankshaft position sensor, or poor wiring connections. 3. Transmission system faults in some vehicles: The engine warning light may also indicate transmission system issues, such as internal transmission faults, slipping, or overheating.
20
0
Share

What does CVT gear mean?

Refers to a device used to adjust the mechanical operating speed and control direction, used for reversing or changing driving speed. The following is an introduction to CVT: 1. Definition: The system mainly includes basic components such as the driving pulley set, driven pulley set, metal belt, and hydraulic pump. Both the driving pulley set and driven pulley set consist of movable discs and fixed discs. The side of the pulley close to the oil cylinder can slide on the shaft, while the other side is fixed. 2. Working principle: In the CVT transmission system, traditional gears are replaced by a pair of pulleys and a steel belt. Each pulley is actually a V-shaped structure composed of two conical discs. The engine shaft is connected to the small pulley, which drives the large pulley through the steel belt.
19
2
Share

What are the precautions for learning to drive at a driving school?

Learning to drive requires attention to the following issues: 1. Maintain a safe following distance: Novice drivers often struggle to judge the distance from the car in front, frequently leaving too much space, which slows down traffic flow and creates opportunities for other vehicles to merge in front, increasing the risk of accidents. Some bold beginners follow too closely but lack the ability to handle emergencies, making rear-end collisions likely if the car ahead brakes or stops suddenly. 2. Wear a seatbelt: It’s crucial to emphasize that after adjusting the driving position, always remember to fasten the seatbelt to avoid sudden panic and unsafe conditions while driving. 3. Release the handbrake: Another common mistake beginners make is forgetting to release the handbrake when starting the car cold. Although the car can still move if the clutch and throttle are well-coordinated, this increases vehicle wear, raises fuel consumption, and may produce a burning smell. Beginners often pull the handbrake at red lights but forget to release it when driving off. If the car stalls at this point, they may panic and sweat without identifying the issue. It’s advisable for beginners to develop the habit of releasing the handbrake immediately when moving to prevent vehicle damage and personal stress.
17
2
Share

What are the penalties for driving a motorcycle with a C-class license?

C-class license holders driving motorcycles will be penalized under the "driving a vehicle not covered by the license" standard, with 12 demerit points, a fine, and in severe cases, up to 15 days of detention. Below is relevant information about C-class licenses: 1. Definition: The C1 driver's license is one type of driver's license code. Applicants can directly apply for the license with their resident ID card anywhere in the country without submitting proof of residence registration. 2. Driving requirements: The C1 driver's license permits driving small and mini passenger cars, as well as light and mini cargo trucks. Light, small, and mini special operation vehicles; small passenger cars with seating capacity of 9 or fewer. According to these standards, the C1 license does not permit driving vehicles with more than 9 seats.
11
4
Share

4 Practical Tips for Choosing Tires

Practical tips for choosing tires are as follows: 1. Look at the tire's ply rating: Common combinations include 1+2, 1+2+1, 2+2+1, and 2+2+2, representing different numbers of plies in the tire construction. The higher the sum of these numbers, the more plies the tire has, making it thicker and more durable with better safety. This also indicates relatively higher costs. 2. Check the tire's material: If the ply count is the same, compare the materials. Common internal materials include nylon, polyester, polyamide, and steel. The best combination is polyamide+steel+polyester, followed by nylon+steel+polyester, and the most basic is nylon+steel+nylon. 3. Examine the sidewall ply count: The more layers in the tire sidewall, the tougher it is, reducing the risk of bulging or blowouts. Two layers are ideal, while one layer is standard. 4. Learn to read the 3T index: Quickly assess the tire's basic performance by checking the 3T index. Note that subjective performance aspects like noise reduction and comfort cannot be determined this way. The three Ts stand for Treadwear (wear resistance), Traction (grip level), and Temperature (heat resistance).
16
5
Share

What is the capacity of the DL250's original three boxes?

DL250's original three boxes have a capacity of 18KG. Below is some related information about the Suzuki DL250: 1. Configuration: It is equipped with practical ABS, original three boxes, and an anti-theft chip. 2. Performance: The DL250 is powered by a twin-cylinder, water-cooled, fuel-injected engine with an actual displacement of 248ml, delivering a maximum output power of 18.4KW and a peak torque of 23.4N.m. The wheelbase is 1430mm, and the total vehicle weight reaches 188KG. 3. Dimensions: The DL250 has a wheelbase of 1430mm, a curb weight of 188kg (without the three boxes), a fuel tank capacity of 17.3L, front tires sized 110/80-17, and rear tires sized 140/70-1.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.