How Can a Vehicle Be Scrapped?

1 Answers
JoannaFitz
07/30/25 3:45am
Owner (individual or company) submits a scrapping application. Individual or company brings the vehicle to be scrapped, along with the vehicle license and the ID card of the person delivering the vehicle, to the Municipal Metal Recycling Corporation. Obtain the Scrapped Vehicle Recycling Certificate. The owner then uses this certificate, along with the vehicle license and license plates, to complete the deregistration of the vehicle at the Municipal Vehicle Management Office. Use the Scrapped Vehicle Recycling Certificate to complete procedures for canceling road maintenance fees, operation fees, and fixed asset deregistration at the Transportation Bureau's Operation Management Office.
Was this review help?
12
2
Share
More Forum Discussions

What are the locations for driver's license renewal in Wujiang?

Wujiang driver's license renewal locations include the Development Zone Branch, Pingwang Branch, Shengze Branch, and Zhenze Branch. The introduction of driver's license renewal time and procedures is as follows: Driver's license renewal time: Within 90 days before the expiration of the driver's license, you can apply for renewal at the vehicle management office where the license was issued or at other vehicle management offices outside the issuing place. However, after the license expires, you cannot renew it elsewhere and must go to the issuing place for renewal. Driver's license renewal procedures: Bring your ID card, driver's license, physical condition certificate, and three photos to the vehicle management office where the license was issued. Fill out the "Motor Vehicle Driver's License Application Form" and submit it along with the renewal application. After paying the processing fee, you will receive your new driver's license.
12
4
Share

How to Replace the Highlander Fuel Filter?

Method for replacing the Highlander fuel filter: 1. Remove the vehicle key and disconnect the Highlander's fuel pump fuse or cut off the vehicle power supply. 2. Remove the rear seat cushion and the cover on the fuel pump to access the fuel pump assembly. 3. After removing the retaining ring, the fuel pump assembly can be taken out. Replace the corresponding components of the old fuel filter with the new fuel filter assembly. Introduction to the filter: 1. The Toyota Highlander gasoline filter is divided into carburetor type and fuel injection type. For gasoline engines using carburetors, 2. The carburetor type filter is located on the inlet side of the fuel pump, with lower working pressure, and generally uses a nylon shell. 3. The fuel injection type filter is located on the outlet side of the fuel pump, with higher working pressure, and usually uses a metal shell.
19
3
Share

What Causes Abnormal Oil Pressure?

Abnormal oil pressure is caused by factors such as insufficient oil storage, dirty oil, thinning oil, or oil pipe leakage. The specific reasons are as follows: Insufficient Oil Storage: When the engine's oil storage is too low, it results in low oil pressure. The solution is to top up the oil. Dirty Oil: Dirty or viscous oil prevents the oil pump from drawing in and pumping out oil, leading to low or no oil pressure. The solution is to change the oil. Thinning Oil: Thinning oil leaks through the engine's friction gaps, causing low oil pressure. The solution is to change the oil or inspect the cooling system. Oil Pipe Leakage: Oil pipe leakage, oil pump damage, or excessive wear of its components can occur. The solution is to conduct repairs. If abnormal oil pressure is detected, immediately stop and turn off the engine. Do not continue driving until the issue is resolved.
13
0
Share

How to Deal with Grooved Brake Discs?

Brake discs with grooves can be dealt with in the following ways: 1. Remove the brake pads and smooth them out with coarse sandpaper; 2. Remove the brake disc and take it to a lathe workshop to grind off the grooves; 3. Replace the brake disc. The brake disc is a crucial component in the braking system, categorized by structure into solid brake discs and ventilated discs. The steps to replace a brake disc are: 1. Lift the car and remove the tire; 2. Unscrew the brake caliper bolts, open the brake caliper, and remove the old brake pads; 3. Push the brake piston back in and install the new brake pads; 4. Reattach the brake caliper, tighten the caliper bolts to the required torque, and reinstall the tire; 5. Press the brake several times to eliminate the gap between the brake pads and the disc, allowing the brake piston to reset; 6. Check if the brake fluid pump is functioning properly.
17
4
Share

Do I Need to File a Record with the DMV for Changing the Front Grille?

Changing the front grille does not require filing a record with the DMV. The following are relevant considerations for vehicle modifications: Illegal Modification Scope: Illegal exterior modifications mainly include self-installing bulbs without adding lenses, changing the car emblem, modifying wheel rims, installing large bumper wraps, adding spoilers, and certain suspension modifications. Legal Modification Scope: Legal interior modifications refer to altering interior facilities, including replacing the steering wheel, installing sport seats, adding instrument equipment, and sound-deadening materials. Modifications Requiring Filing: Before modifying a vehicle, you can consult the traffic management department to check if the intended modification is legal. You can apply for relevant filing, and once approved, the modified vehicle will be considered legally modified.
12
5
Share

What is the normal tire pressure for a Focus?

The normal tire pressure for a Focus is between 2.3 and 2.5 bar. The effects of overinflated tires are: 1. Increased friction between the tire and the ground, reducing tire grip; 2. Affects the vehicle's braking performance and driving comfort, accelerating wear on the central tread and shortening tire lifespan. The effects of underinflated tires are: 1. Increased contact area between the tire and the ground, making the steering wheel heavier and affecting driving; 2. Tires are prone to overheating, increasing the risk of blowouts; 3. The tire body expands, making it more likely for cracks to appear on the inner and outer sides of the tire; 4. Accelerates rubber aging and increases tire wear. The Focus is a compact 4-door, 5-seater sedan. Taking the 2021 Focus as an example, its body dimensions are: length 4647 mm, width 1810 mm, height 1468 mm, with a wheelbase of 2705 mm, a fuel tank capacity of 53 liters, and a trunk capacity of 511 liters.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.