···
Log in / Register

Honda Vezel Intermittently Making Abnormal Noises?

4 Answers
VanEmery
08/27/25 7:37am

Honda Vezel makes abnormal noises at intervals, which usually indicates a problem in a certain part of the car, triggering the electronic alarm system to issue a warning. It could be due to an unfastened seat belt or excessively high water temperature. Below are the specific reasons: Unfastened Seat Belt: If the seat belts in the driver or front passenger seats are not fastened properly, the car will emit a warning sound; if the handbrake is not fully released, abnormal noises will occur while driving; if multimedia functions are not turned off, and the car has an automatic WiFi search feature, it may also make abnormal noises when not connected. Excessively High Water Temperature: If the water temperature is too high, the car will make abnormal noises. The dashboard warning light does not show the water level in the radiator but only the temperature. Once the water temperature warning light comes on, it indicates insufficient radiator coolant. Low Tire Pressure: The car has electronic components that monitor the tires. If a tire is leaking or has low pressure, the information will be transmitted to the alarm system.

Was this review help?
3
4
Share
Theo
09/09/25 6:22am

I've been driving this Honda Vezel for a year and a half, occasionally hearing intermittent abnormal noises like creaking or dull knocking sounds. Based on my years of driving experience, common causes are likely suspension system issues, such as aging shock absorbers or worn bushings, which become more noticeable on bumpy roads; or a loose engine compartment belt that makes intermittent noises during acceleration or sharp turns. It could also be loose interior plastic trim that makes cracking sounds with large temperature variations. I remember once ignoring similar noises, and a minor issue turned into a major one, costing me thousands more to repair. I recommend going to a professional shop for inspection immediately—don't delay too long. Although Honda cars are durable, abnormal noises are often early warning signs of loose components. Fixing them early can save a lot of money and safety risks.

Was this review help?
7
4
Share
Expand All
DeLydia
10/23/25 7:13am

My Vezel also experiences intermittent abnormal noises, which are quite annoying but mainly concerning from a safety perspective. The noises might stem from worn brake pads or suspension damage, which can distract the driver and even increase the risk of accidents. Issues with engine auxiliary components like bearings or the fan can also cause intermittent noises, especially when temperatures rise. After a check-up at the 4S shop, the technician mentioned that abnormal noises can be categorized into high-frequency and low-frequency: plastic sounds are easier to fix, while mechanical sounds require prompt attention. While driving, pay attention to the source of the noise—different issues can arise from the front or rear. If you notice any, avoid long-distance trips and seek repairs as soon as possible. For prevention, regular maintenance and cleaning the chassis can reduce faults, ensuring safety comes first.

Was this review help?
10
4
Share
Expand All
McAlice
12/06/25 7:37am

The most common causes of intermittent noises in the Honda Vezel are suspension wear, loose belts, or bearing failure, often triggered by road conditions or temperature changes. As an enthusiast, I've encountered similar issues: engine mount problems causing noises only during acceleration. Key to identifying the source: front-end noises may indicate engine belt issues, while rear-end noises point to suspension. Avoid disassembling parts randomly—simple checks include inspecting tires and chassis for obvious looseness, but professional diagnostic tools are recommended for accurate assessment. Repairs are generally straightforward, often requiring part replacements for minor issues. Delaying fixes may escalate into major overhauls, negatively impacting driving experience.

Was this review help?
13
4
Share
Expand All
More Forum Discussions

how to get urine out of car seats

The most effective way to get urine out of car seats is to immediately blot up the liquid, then use an enzymatic cleaner specifically designed to break down urine crystals. Avoid using ammonia-based cleaners, as they can set the stain and intensify the odor. The key is to act quickly and target the uric acid, which is what causes the persistent smell. Time is your biggest enemy. The longer urine sits, the deeper it soaks into the foam padding beneath the seat fabric, making odor removal much harder. Your first step is always to blot, not rub . Rubbing spreads the urine and pushes it deeper. Use a stack of paper towels or microfiber cloths to absorb as much moisture as possible. For the cleaning solution, an enzymatic cleaner is non-negotiable for complete odor removal. These cleaners use live bacteria to digest the urine proteins and uric salt crystals that regular cleaners leave behind. Popular and effective brands include Nature's Miracle Urine Destroyer and Rocco & Roxie Stain & Odor Eliminator. After applying the cleaner according to the product instructions, you must extract it. A wet/dry vacuum is ideal for this, but you can also blot repeatedly with clean towels. For severe or old stains, a deep clean with an upholstery cleaner or steam cleaner may be necessary to reach the seat foam. After cleaning, air drying is critical. Keep windows down or use fans to circulate air; heat can bake in any remaining odor. Cleaning Method Primary Use Case Key Advantage Potential Drawback Enzymatic Cleaner Fresh or old urine stains Breaks down uric acid crystals at the source Requires longer dwell time to work DIY Vinegar Solution Fresh stains, light odor Readily available, inexpensive Less effective on old, set-in stains Baking Soda Paste Surface odor absorption Helps neutralize smells after cleaning Does not clean deep stains Upholstery/Steam Cleaner Severe stains, deep cleaning Extracts moisture and dirt from deep within fabric Requires equipment rental/purchase Professional Detailing All other methods have failed Highest level of cleaning and odor elimination Most expensive option
4
1
Share

how to get smell out of car vents

The most effective way to get a smell out of your car vents is a multi-step process: replace the cabin air filter , clean the evaporator core with a specialized foam cleaner, and fumigate the entire ventilation system with an antibacterial treatment. Musty odors are typically caused by mold and mildew growing on the evaporator coil, which is located deep within the HVAC system. The table below outlines the primary causes of vent odors and the corresponding solutions. Cause of Odor Recommended Solution Expected Outcome Clogged cabin air filter harboring debris Replace with a new, high-quality filter Immediate improvement in air flow and reduction of particulate-based smells Mold/Mildew on A/C evaporator coil Apply an HVAC system cleaner foam Kills odor-causing bacteria and fungi at the source Bacterial growth in ventilation ducts Use an antibacterial spray or bomb designed for cars Sanitizes the entire air pathway for a long-term solution External contaminants (e.g., dead rodent) Visually inspect and manually remove the source; may require professional help Eliminates the primary odor source before cleaning Spills on floor mats/seats seeping into system Thoroughly clean interior surfaces and shampoo carpets Prevents odors from being drawn into the fresh air intake Start by locating your cabin air filter (usually behind the glove box or under the hood near the windshield) and replacing it. This is a simple, low-cost fix that often makes a big difference. For a musty smell that persists after a filter change, the evaporator core is the likely culprit. You'll need a commercial A/C evaporator cleaner, which comes with a long tube to spray the foam directly onto the coil through the condensate drain line or the blower motor housing. Finally, to ensure all ducts are clean, run the fan on high with the windows down and spray a disinfectant fogger into the outside air intake at the base of the windshield. Let the car circulate for 10-15 minutes. For severe, persistent odors, a professional detailing shop with an ozone generator is the most reliable option.
8
3
Share

how to get car oil out of can fur

The fastest way to get car oil out of faux fur (the synthetic material often used in car interiors) is to act quickly by blotting, not rubbing, and using a combination of absorbent powders and a targeted degreaser. The key is to break down the oil without spreading the stain or damaging the fabric's texture. Start by blotting up any excess oil with a clean, dry paper towel or cloth. Press down firmly and repeat until no more oil transfers. Rubbing will only grind the oil deeper into the fibers. Next, apply an absorbent powder like cornstarch, baking soda, or even cat litter (the non-clumping kind) over the stain. This will draw the oil out from the faux fur. Let it sit for at least 15-20 minutes, then vacuum it up completely. For the remaining stain, use a commercial degreaser designed for automotive interiors or a DIY mixture of dish soap (like Dawn) and warm water. Dish soap is a surfactant, meaning it breaks the surface tension of oil, allowing it to be rinsed away. Apply a small amount to a clean cloth, work it into the stain in a circular motion, and then blot with a damp cloth to rinse. You may need to repeat this process. Always do a spot test on an inconspicuous area first to ensure colorfastness. Step Action Key Product/Technique Purpose 1 Immediate Blotting Paper Towels Lift excess surface oil 2 Absorbent Powder Application Cornstarch or Baking Soda Draw out embedded oil 3 Vacuuming Vacuum Cleaner Remove dried powder 4 Degreasing Automotive Interior Cleaner or Dish Soap Break down oil molecules 5 Rinsing & Drying Damp Cloth, Air Dry Remove soap residue, prevent water stains Let the area air dry completely. Once dry, you may need to gently brush the faux fur with a soft-bristled brush to restore its texture.
6
4
Share

how to install a car radio system

Installing a car radio system is a manageable DIY project if you're comfortable with basic tools and wiring. The core process involves removing the old unit, connecting a wiring harness adapter for your new radio, and securing everything into the dashboard. The most critical step is using a vehicle-specific wiring harness adapter , which allows you to connect the new radio without cutting the factory wires, preserving your car's electrical system. For a standard single-DIN or double-DIN stereo (the standard size slots in most dashes), the job can take 1-3 hours. Tool / Item Needed Purpose / Specification Trim Removal Tools Plastic pry tools to safely remove dashboard panels without scratching. Vehicle-Specific Wiring Harness Adapter that plugs into car's factory wiring; essential for a clean install. Dash Kit Fills gaps between new radio and dashboard for a factory-fit look. Antenna Adapter Ensures the new radio connects to the car's AM/FM antenna. Multimeter Tests wires for power, ground, and speaker connections (12V DC). Before you start, always disconnect the negative battery terminal to prevent short circuits. Aftermarket radios use a standardized color code for speaker wires (e.g., white/white-black for front left), but a multimeter is the only way to be 100% sure. Once the new harness is connected, use crimp connectors or solder for secure joints—never just twist wires together. Test the radio for power and sound before you fully reassemble the dash. If your car has steering wheel audio controls, you'll need an additional interface module to retain them. While many installations are straightforward, cars with complex infotainment systems are best left to professionals to avoid damaging integrated features.
15
0
Share

how to get rid of bugs in the car

The most effective way to get rid of bugs from your car's exterior and prevent interior infestations involves a multi-step process: immediate removal of fresh splatter, a thorough deep cleaning, and implementing preventative measures. For fresh bug guts, soaking them with a dedicated bug and tar remover or even a vinegar-water solution for a few minutes before gently wiping is key to avoid scratching the paint. For interior bugs, a strong vacuum is your first line of defense. Letting bug residue bake on in the sun makes removal much harder and can permanently etch the clear coat. The table below compares common cleaning agents and their effectiveness. Cleaning Method / Agent Primary Use Effectiveness on Fresh Bugs Effectiveness on Baked-on Bugs Risk to Paint/Finish Cost Estimate Dedicated Bug & Tar Remover Exterior Very High High Low (when used as directed) $8 - $15 Isopropyl Alcohol (Diluted) Exterior/Interior High Medium Medium (can strip wax) $3 - $5 White Vinegar & Water Solution Exterior/Interior Medium Low Low $2 - $4 Baking Soda Paste Exterior Low Medium Low (gentle abrasive) $2 - $3 Strong Vacuum with Crevice Tool Interior High for loose debris N/A None N/A Steam Cleaner Interior Very High Very High Low on most surfaces $100+ (for machine) After cleaning the exterior, it's crucial to reapply a protective wax or sealant . This creates a slippery barrier that makes it easier to wash off bugs next time. For the interior, focus on eliminating what attracts them. Crumbs and sticky spills are a major draw. Regularly vacuuming floor mats, seats, and crevices is essential. If you suspect an infestation, thoroughly clean and consider using a safe, pet-friendly insect repellent designed for cars, but avoid spraying it directly on screens or sensitive electronics.
10
0
Share

how to get a stain off a car seat

The fastest way to remove a stain from a car seat is to first identify the fabric type and the stain source. For most common stains on cloth upholstery, a simple solution of dish soap (like Dawn) and warm water is highly effective. For tougher stains, an upholstery cleaner or a vinegar and water mixture may be necessary. Always blot, never rub , and test any cleaner on a hidden area first to prevent damage. Start by vacuuming the area to remove any loose debris. For a basic soap solution, mix a tablespoon of clear dish soap with two cups of warm water. Using a clean microfiber cloth, apply the solution by blotting the stain from the outside in. Rinse the cloth with clean water and blot the area to remove soap residue. Then, use a dry towel to absorb as much moisture as possible and let the seat air dry completely. For stubborn stains like coffee or ink, a 1:1 mixture of white vinegar and water can be more effective. For grease, a dry-cleaning solvent or baking soda paste might be needed. Leather seats require specific, pH-balanced leather cleaners and conditioners to avoid drying and cracking the material. Stain Type Recommended Cleaning Agent Key Consideration General Dirt/Spills Dish Soap & Warm Water Blot, don't scrub. Rinse thoroughly. Coffee/Juice White Vinegar & Water Solution Neutralizes odors and breaks down sugars. Ink Rubbing Alcohol (Isopropyl) Test on hidden area first; can fade some dyes. Grease/Oil Baking Soda Paste or Dry-Cleaning Solvent Baking soda absorbs oil before vacuuming. Blood Cold Water & Enzyme Cleaner Hot water sets protein-based stains like blood. Prevention is key. Using seat covers can protect your upholstery. For persistent or large stains, consulting a professional auto detailer is the safest bet to avoid damaging your seats.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.