Ground Clearance of Model Y?

1 Answers
MichaelAnn
07/29/25 4:15pm
The minimum ground clearance of Model Y is 150mm. The minimum ground clearance of Model Y refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as stones and stumps without collision. The higher the ground clearance of Model Y, the better its off-road capability. However, if the ground clearance is too high, the stability at high speeds may decrease. Model Y is the fifth vehicle launched by Tesla since its establishment in 2003. Its body dimensions are: length 4750mm, width 1921mm, height 1624mm, with a wheelbase of 2890mm. Generally, the ground clearance of sedans ranges between 110mm and 150mm, while SUVs have a ground clearance between 200mm and 250mm. However, the ground clearance of Model Y is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the load variations of the Model Y. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban areas with good road surfaces, vehicles with lower ground clearance can enhance stability and comfort. For long-distance travel or regions with poor road conditions, vehicles with higher ground clearance are preferable to avoid scraping or damaging the chassis, considering the vehicle's off-road performance.
Was this review help?
4
0
Share
More Forum Discussions

What are the reasons for the failure of the Volkswagen Magotan parking assist system?

Magotan parking assist system failure may be caused by wiring or control unit issues. It is recommended that the owner promptly visit a repair shop or 4S store for inspection and repair to avoid affecting the driving experience. Below is a partial introduction to the parking assist system: 1. Introduction: The parking assist system, also known as the parking radar system, can inform the driver of surrounding obstacles through sound and visual display. It eliminates the troubles caused by the driver's need to look around when parking, reversing, or starting the vehicle, helping to clear blind spots and improve driving safety. 2. Working principle: Ultrasonic detection, similar to the principle that bats can fly at high speed at night without colliding with any obstacles.
6
5
Share

What Causes Misfire in Cylinder 3?

Misfire in cylinder 3 is caused by damage to external components. Here are specific details about cylinder 3 misfire: 1. Caused by damage to external components: Mainly involves components around the combustion chamber such as valves, valve seats, valve guides, and spark plugs. 2. Misfire caused by failure to ignite or delayed ignition of the air-fuel mixture in the cylinder. For the first scenario, typically check the spark plugs, clean carbon deposits from the intake and exhaust valves, and inspect the turbocharger for issues such as wear or erosion of the turbine wheel. The second scenario usually occurs when an abnormal condition in a certain component or part causes unstable engine regulation by the ECU, failing to meet the theoretical values calibrated by the ECU, resulting in misfire.
15
5
Share

What is the fuel consumption of the Encore 1.4t?

The Buick Encore 1.4t has a fuel consumption of 7.2L per 100 kilometers. Below is relevant information about the Encore: 1. Powertrain: The Encore is equipped with two combinations: a 1.0T SIDI direct-injection turbocharged engine paired with a 6-speed DSS intelligent transmission, and a 1.3T SIDI direct-injection turbocharged engine paired with a CVT intelligent continuously variable transmission. The maximum power outputs of these two engines are 92kW and 121kW, respectively, both meeting the China VI emission standards. 2. Safety features: The entire lineup comes standard with ESC electronic stability control, ROM rollover sensing system, HSA hill start assist, CBC cornering brake control, TPMS intelligent tire pressure monitoring, and a series of other electronic safety systems. 50% of the models are equipped with intelligent driving assistance systems such as PD pedestrian detection, SBZA side blind zone alert, LKA lane keep assist, FDI following distance indicator, and FCA forward collision alert.
8
5
Share

What does 'Radar Ready' mean?

Radar Ready means that the DRCC (Dynamic Radar Cruise Control) or speed cruise control is activated. The speed cruise control system can be operated using the control buttons on the right side of the steering wheel, with the far-right button being the speed cruise control switch. If you need to turn off the Radar Ready reminder, you can press this button to deactivate it. More related information is as follows: 1. Classification: Radar is divided into military and civilian types, but their common function is to determine the physical position of a target through radio waves. Military radar is used to search, monitor, and identify military targets, while civilian radar is mainly used for meteorological services, aviation, and ship traffic control. 2. Introduction: Radar, also known as 'radio location,' is an electronic device that uses electromagnetic waves to detect targets. Its principle is that the radar emits electromagnetic waves to illuminate the target and receives its echo, thereby obtaining information such as the distance from the target to the radar, the rate of change in distance (radial velocity), azimuth, and height. Radar is divided into military and civilian types, but their common function is to determine the physical position of a target through radio waves.
8
2
Share

What Causes the Drive Shaft Bolts to Frequently Loosen?

Drive shafts transmit force through bolts, which are subjected to both radial and axial forces, as well as impact during startup and stopping, making them prone to loosening. Below are the relevant details: 1. Aligning the Drive Shaft: Loose drive shaft bolts require alignment. The drive shaft is a high-speed, minimally supported rotating body, making its dynamic balance crucial. Typically, drive shafts undergo dynamic balance testing before leaving the factory and are adjusted on a balancing machine. 2. Components of the Drive Shaft include: Universal Joint: A critical component of the drive shaft. In rear-wheel-drive vehicles, the engine, clutch, and transmission are mounted as a unit on the frame, while the drive axle is connected to the frame via elastic suspension, necessitating a connection between the two. Sliding Spline: This involves welding the spline sleeve to the flange yoke and the spline shaft to the drive shaft tube. Modern drive shafts have evolved from traditional designs by integrating the spline sleeve with the drive shaft tube and combining the spline shaft with the flange yoke. Bushing: Designed to reduce friction and wear during shaft movement, its basic function is similar to that of a bearing but at a lower cost. However, due to higher friction resistance, it is only used in certain components.
4
2
Share

Where is the BMW 5 Series mirror heating located?

The BMW 5 Series mirror heating can be activated by turning on the automatic wiper sensor switch. After the vehicle is started, the mirror heating function will sense the temperature and automatically activate when it's below 15 degrees. Here is some extended information about the BMW 5 Series: 1. Introduction: It is available in two versions, a fuel version and a plug-in hybrid version, both offering M Sport package and Luxury package exterior options. 2. Interior: Spacious with comfortable seats. The seats feature 20-way electric adjustment and come with comfort headrests, elevating ergonomic comfort to a new level. Dark-grained matte ash wood panels are paired with pearl chrome trim, combining delicate softness with refined design.
9
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.