Engine Starts, Gold Flows; The Complete Rhyme When the Door Closes

What is the normal tire pressure for the Geely Boyue?

The normal tire pressure for the Geely Boyue is between 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be increased by 0.2 bar in winter and reduced by 0.1 bar in summer. The tire pressure monitoring system in the Geely Boyue can be viewed on the dashboard, which includes special function prompts (tire pressure monitoring, active safety information, including distance alerts, ACC cruise mode, lane departure warning, collision warning, PEPS, etc.). The tire pressure monitoring reset method for the Boyue is relatively simple—just drive for a while, and it will return to normal data without any additional settings. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no seal on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: 1. Abnormal tire pressure. Typically, the system will alert if the pressure is below 1.8 bar or exceeds 3.0 bar. In such cases, the tire should be checked and the pressure adjusted. 2. The tire pressure monitoring system was not reset. After inflating the tires, if the tire pressure reset is not performed promptly, the system may still record the previous data, causing the indicator light to remain on. Simply performing a tire pressure reset will resolve this issue. 3. Damaged tire pressure sensor. The tire pressure sensor, which is installed inside the tire and connected to the tire valve, monitors the tire pressure. If the sensor is damaged due to impact while driving, the tire pressure warning light may also illuminate. In such cases, the only solution is to replace the sensor with a new one.

12

0

Share

Is the red terminal on a car battery positive or negative?

In a car battery, the red terminal is positive, and the black terminal is negative. The method for jump-starting a car battery is as follows: 1. Prepare two jumper cables; 2. Find a vehicle that can operate normally; 3. Position the two vehicles facing each other; 4. Connect the jumper cables to the batteries, positive to positive and negative to negative; 5. Start the functioning vehicle first, then start the vehicle being jump-started, and disconnect once started. Methods for maintaining a car battery: 1. Regularly inspect the battery; 2. Avoid overcharging; 3. Gently press the brake when starting; 4. Ensure the battery is fully charged if the vehicle is parked for an extended period; 5. Protect the battery from excessive heat and extreme cold.

10

4

Share

How to Tell if a Used Car's Odometer Has Been Rolled Back?

Here are specific methods to determine if a used car's odometer has been rolled back: 1. Check maintenance records: Visit the 4S shop to inquire about the vehicle's maintenance records. This is the simplest and most straightforward method. It is particularly suitable for relatively new cars, as such vehicles are typically serviced at 4S shops, allowing access to their maintenance records. 2. Observe interior wear and aging: Experienced mechanics can often spot discrepancies by examining the wear and aging of the interior, as wear levels are proportional to the vehicle's mileage. Key areas to inspect include: the dust cover under the gear lever, door panels and handles, dashboard buttons, center console, seat edges for wear and shine, which can help estimate the vehicle's mileage. 3. Check steering wheel and pedal wear: The wear on the steering wheel, accelerator pedal, brake pedal, and clutch pedal directly reflects the vehicle's usage frequency. These are the parts most frequently touched by the driver. While some drivers use steering wheel covers to reduce wear, subtle signs of wear can still be detected. 4. Tire wear and production date: Experienced drivers know that car tires typically last around 50,000 to 60,000 kilometers. If the tire treads are flat or the edges are worn smooth, it indicates the car has been driven extensively. When inspecting a used car, if the four tires show uneven wear, it may suggest the car was involved in an accident. If all tires have been replaced, the mileage likely exceeds 50,000 kilometers. 5. Inspect the OBD port: Another method is to check the OBD port, though this is less commonly used unless for maintenance checks, so it can serve as a supplementary reference.

1

3

Share

How to Open the Hood of a Buick Car?

Method to open the Buick hood: 1. There is a handle below the left hand side of the driver, pull it; 2. After the front hood is opened, reach inside and feel upwards, there is a mechanical lock, press the button down; 3. The hood release is located on the left side of the foot pedal, there is a hook, pull it, there is a hook at the front of the hood, press it upwards with your hand, sit in the driver's seat, there is a release lever next to the left knee, pull it to open the first safety latch; 4. Face the vehicle, there is a lever in the middle position, lift it upwards to open the second safety latch, after opening the steering wheel, there is a black thing at the lower left, then pull the front cover, and the engine hood will be opened.

11

1

Share

How to Turn Off the ECO Mode in Land Cruiser?

To turn off the ECO mode, there is a button next to the gear shift. On the left is ECT, and on the right is 2nd gear start. When you press the button towards the ECT direction, the ECO mode will be turned off. The ECO mode in cars serves the following three purposes: 1. The car's ECO is an energy-saving mode: When the ECO mode is activated, it comprehensively evaluates and analyzes factors that affect fuel consumption, such as automatic transmission gear, engine speed, vehicle speed, braking, and transmission oil temperature; 2. The ECU control unit calculates the optimal fuel amount and supplies it to the engine for operation: This effectively reduces fuel consumption compared to normal driving modes; 3. After activating the ECO mode, the throttle opening corresponding to the same accelerator pedal depth is smaller: The transmission shift logic prioritizes fuel economy, and it also adjusts the air conditioning output power.

12

3

Share

What to Do When the Tail Lights of a Sedan Stay On?

The methods to address continuously illuminated tail lights on a sedan are: 1. Check if the brake switch is short-circuited and replace it if necessary; 2. Visit a 4S store or a professional repair shop for expert assistance. Tail lights are installed at the rear of the vehicle, with the main color being red to enhance the penetration of the light source, ensuring that following vehicles can spot the car ahead under low visibility conditions, thereby preventing rear-end collisions. The replacement steps for sedan tail lights are: 1. Use a cross screwdriver or socket to remove the bolts; 2. Pull the light assembly out from the rear pillar; 3. Turn the socket counterclockwise and remove it; 4. Remove the old bulb and insert a new one.

11

5

Share

Engine Starts, Gold Flows; The Complete Rhyme When the Door Closes

What is the normal tire pressure for the Geely Boyue?

Is the red terminal on a car battery positive or negative?

How to Tell if a Used Car's Odometer Has Been Rolled Back?

How to Open the Hood of a Buick Car?

How to Turn Off the ECO Mode in Land Cruiser?

What to Do When the Tail Lights of a Sedan Stay On?

Will External Tire Pressure Monitoring Cause Air Leakage?

What are the reasons for a car suddenly stalling and failing to start?

What are the steps for disassembling the center console of the XC60?

What is the maximum speed of the Vision X3?