Driving Test Subject 3 Lighting Mnemonic Table?

1 Answers
EverlyDella
07/30/25 3:37am
Subject 3 lighting test mnemonic: 1. Driving at night without street lights and under poor lighting conditions; (high beam) 2. Meeting non-motor vehicles on narrow roads at night; (low beam) 3. Following vehicles closely in the same direction at night; (low beam) 4. Meeting motor vehicles at night (low beam) 5. Passing over arch bridges and pedestrian crossings at night; (alternate between high and low beams) 6. Passing sharp curves and slopes at night; (alternate between high and low beams) 7. Passing intersections without traffic signals at night; (high and low beams) 8. Vehicle breakdown on the road at night, obstructing traffic and difficult to move. (width lights, hazard warning lights) 9. Driving in foggy weather (fog lights, hazard warning lights) Summary: No lights turn on high beam, following or meeting vehicles use low beam, the word 'passing' means alternate between high and low beams.
Was this review help?
4
0
Share
More Forum Discussions

What is the plastic film inside the car door called?

The plastic on the inside of the car door is called the door seal or sealing strip. Below is some relevant information: 1. Car doors require good sealing to prevent dust, water, and noise. In addition to proper size coordination between the door and the car body, another important factor is the sealing strip embedded or pasted on the door frame and door. The sealing strip is a rubber product with a hollow cross-section. Its flexibility allows it to fill gaps of varying sizes—when the gap is large, the pressure on the seal is minimal, and when the gap is small, the pressure increases. 2. Sealing is a crucial quality indicator for the entire vehicle, and the car sealing strip is one of the key components that determine this performance. It is widely used in areas such as the front and rear windshields, doors, windows, engine compartments, and trunks, filling gaps between body parts. It serves functions like shock absorption, waterproofing, dustproofing, sound insulation, and decoration, providing protection for both passengers and the vehicle.
7
1
Share

What is the 0-100 km/h acceleration time of the Volkswagen Magotan?

According to official data, the 0-100 km/h acceleration time of the Volkswagen Magotan is 9.1 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time are as follows: Torque: Torque, in simple terms, represents how much force is available. The greater the torque, the stronger the force pushing the vehicle, naturally resulting in faster acceleration. The maximum torque of the T-Roc is 250 Nm, with a 0-100 km/h acceleration time of 9.1 seconds. The Volkswagen Magotan has a torque of 350 Nm, also achieving a 0-100 km/h acceleration time of 9.1 seconds. Transmission efficiency: The transmission serves as the medium for power transfer, inevitably involving power loss. The higher the transmission efficiency, the better the acceleration performance. Generally, the ranking of transmission efficiency is as follows: manual transmission > dry dual-clutch transmission (DCT) > wet dual-clutch transmission (DCT) > automatic transmission (AT) > continuously variable transmission (CVT). The Volkswagen Magotan is equipped with a 7-speed wet dual-clutch transmission (DCT). Power-to-weight ratio: The relationship between horsepower and vehicle weight is referred to as the power-to-weight ratio (unit: Hp/T). The higher the power-to-weight ratio, the faster the acceleration. The T-Roc has a power-to-weight ratio of 103 Hp/T, with a 0-100 km/h acceleration time of 9.1 seconds. The Volkswagen Magotan has a power-to-weight ratio of 85.7 PS/T, also achieving a 0-100 km/h acceleration time of 9.1 seconds.
18
4
Share

Which three buttons are used to restart the screen of the Audi A4L?

The three function buttons for restarting the screen of the Audi A4L are setup, the rotary button, and the upper-right button. These buttons are located below the central control screen. To restart the screen, press and hold all three buttons simultaneously. Another method to restart the screen is to turn off the vehicle and then restart it. The Audi A4L is available in three powertrain variants: 30TFSI, 40TFSI, and 45TFSI. Except for the 30TFSI, which is equipped with a 1.4T engine, all other models are powered by the EA888 series 2.0T turbocharged engine, available in both high and low power versions.
18
2
Share

What is the ground clearance of the Golf 8?

The minimum ground clearance of the Golf 8 is 115 mm. The minimum ground clearance of the Golf 8 refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which is used to indicate the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. The higher the ground clearance of the Golf 8, the better its off-road capability. However, if the ground clearance is too high, the stability at high speeds may decrease. The Golf 8 is a classic compact hatchback family car launched by FAW-Volkswagen. The body dimensions of the Golf 8 are 4296 mm in length, 1788 mm in width, and 1471 mm in height, with a wheelbase of 2636 mm. The Golf 8 features front-engine, front-wheel drive, with a MacPherson strut independent front suspension and a torsion beam non-independent rear suspension. The body structure is of a unibody design. Generally, the ground clearance of sedans ranges between 110 mm and 150 mm, while SUVs have a ground clearance between 200 mm and 250 mm. However, the ground clearance of the Golf 8 is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the Golf 8's load variations. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For well-paved urban roads, a vehicle with lower ground clearance can enhance stability and comfort. For frequent travel to remote areas or regions with poor road conditions, a vehicle with higher ground clearance may be preferable to avoid scraping or damaging the chassis.
5
2
Share

Is Wheel Balancing Necessary When Installing New Tires?

Wheel balancing is necessary when installing new tires. Generally, any replacement or repair of the tire system requires wheel balancing because prolonged use can lead to the detachment of balancing weights, causing an imbalance in the tire's weight distribution. Tire balancing is divided into two types: dynamic balance and static balance. Dynamic imbalance can cause the wheel to wobble, leading to wave-like wear on the tire; static imbalance can result in bumps and bouncing, causing flat spots on the tire. Car tires are one of the essential components of a vehicle, directly in contact with the road surface. Together with the car's suspension, they help absorb shocks during driving, ensuring good ride comfort and smooth driving.
19
5
Share

Do I Need to Replace the Tire if a Nail Punctures a Tubeless Tire?

Tubeless tires punctured by a nail may or may not need replacement depending on the location of the puncture. If the tread is punctured and the damage is not severe, it can be repaired and continue to be used. However, if the sidewall is punctured, it is recommended to replace the tire. The tires used in cars are all tubeless tires, which do not have an inner tube and offer better performance. Car tires are one of the important components of a vehicle, directly contacting the road surface and working together with the car's suspension to reduce the impact on the car while driving, ensuring good ride comfort and smooth driving, maintaining good adhesion between the wheels and the road surface, and improving the car's traction, braking, and passing ability.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.