Drive BMW, Ride Mercedes or Drive Mercedes, Ride BMW?

What Causes a Motorcycle to Fail to Shift into Second Gear?

Gear lever malfunction, gear hook spring breakage, or issues with the shift drum or star gear. It could be problems with the shift arm on the right side of the shift drum, the shift hook, or the shift drum positioning device. Open the right engine cover for inspection; generally, the gear teeth and shift forks should be fine. Below is relevant information: Gear pedal not moving: Check if the shift lever on the push-pull arm assembly is bent—if so, straighten it. Verify the coaxiality of the left and right engine housing holes supporting the shift lever; adjust if inconsistent. Disassemble the gearbox to inspect if the shift fork is stuck or if foreign objects are jamming the gear. Gear pedal not returning: Inspect if the return spring is broken—replace if necessary. Check if the shift adjustment screw is loose—if so, flatten the locking washer's edge and tighten the lock nut.

17

0

Share

Is it okay to rev the engine in neutral on a motorcycle?

Revving the engine in neutral on a motorcycle is not advisable as it can easily lead to carbon buildup. When you start the bike and immediately rev the throttle, it can cause significant damage to the vehicle. If you press the throttle right after starting, the engine does not get properly lubricated before it starts working, which increases wear and tear on various components. Below is some relevant information: Aggressive Driving: Under normal circumstances, aggressive driving refers to revving the engine beyond 6000 RPM. Revving between 3000 and 6000 RPM is considered spirited driving, while anything below 3000 RPM is considered normal driving. Causing Carbon Buildup: Even after the bike has warmed up, it is important to avoid aggressive driving, meaning you should not rev the throttle excessively. This is because the coolant temperature has not yet risen. Normally, the engine operates at a temperature of around 80-90 degrees Celsius. Once the coolant temperature rises, the fuel combustion rate will stabilize. If gasoline does not burn completely, it can easily lead to carbon buildup.

4

2

Share

How often should a new motorcycle be inspected?

Motorcycles should be inspected once every 2 years within the first 4 years; after exceeding 4 years, they must be inspected annually. Specifically, after a new motorcycle is registered, it requires biennial inspections for the first four years, followed by annual inspections thereafter. Under normal circumstances, motorcycles are scrapped after 10 years. However, if the vehicle condition is good and passes inspection, the service life can be extended for up to 3 additional years, resulting in a maximum mandatory scrapping period of 13 years. Below are the relevant regulations: According to Article 16 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China": Motor vehicles shall undergo safety technical inspections according to the following intervals from the date of registration: For passenger vehicles used for commercial purposes: Commercial passenger vehicles must be inspected annually within the first 5 years; after exceeding 5 years, inspections are required every 6 months. For cargo vehicles: Cargo vehicles and large or medium-sized non-commercial passenger vehicles must be inspected annually within the first 10 years; after exceeding 10 years, inspections are required every 6 months.

18

1

Share

What is the valve clearance adjustment for Cummins 2.8?

Intake valve 0.35, exhaust valve 0.45. Below is relevant information: Valve clearance: It refers to the gap between the end of the valve stem and the valve transmission components when the valve is fully closed. Necessity of valve clearance: When the engine is running, the valve will expand due to temperature rise. If there is no gap or the gap is too small between the valve and its transmission components in the cold state, the thermal expansion of the valve and its transmission components in the hot state will inevitably cause the valve to not close tightly, resulting in air leakage during the compression and power strokes of the engine, and a decrease in power. In severe cases, it may even be difficult to start. To eliminate this phenomenon, valve clearance is usually reserved during cold assembly of the engine to compensate for the expansion of the valve after heating. Some engines use hydraulic tappets, and the length of the tappet can automatically change to compensate for the thermal expansion of the valve at any time, so no valve clearance needs to be reserved.

15

0

Share

What are the parking techniques for automatic transmission cars?

Automatic transmission parking techniques are: 1. Press the foot brake to stop the car. 2. Shift the gear from D to N. 3. Pull the handbrake and turn off the engine. 4. Release the foot brake, but do not turn off the power (to confirm that the car is completely stopped under the effect of the handbrake). 5. Press the foot brake and shift the gear from N to P. 6. Release the foot brake. 7. Turn the key back, turn off the power, and pull out the key. The following is an explanation of automatic transmission car gears: 1. P—Parking, parking gear, starting gear. When the car is parked and not in use, the gear is in this position, and the wheels are mechanically locked to prevent rolling. 2. R—Reverse, reverse gear. Used when reversing. 3. N—Neutral, neutral gear. Used when temporarily stopping (such as at a red light). Note that this gear position means neutral, and to prevent the car from rolling on a slope, the brake must be pressed. 4. D—Drive, forward gear, also known as driving gear. Used when moving forward.

17

1

Share

What type of engine oil does the Honda Lingpai use?

Honda Lingpai can use the original semi-synthetic engine oil. The following is the relevant introduction about the engine oil for Honda Lingpai: 1. Lingpai engine oil model grade: SM or SN grade can be used, and the viscosity can be 0W20, 0W30 and 5W30 engine oil. 2. Engine oil is extremely important for the movement of the engine because it is responsible for the two major functions of lubrication and heat dissipation. Therefore, at any time, the engine must never lack engine oil. However, the consequences of excessive addition (exceeding the upper limit of the scale) are not good. 3. Too much engine oil will increase the rotation resistance of the crankshaft, reduce the output power of the engine, and the excess engine oil will enter the combustion chamber to participate in combustion, causing the vehicle to burn engine oil, emit blue smoke, and even increase fuel consumption. 4. When adding lubricating oil, it must be kept slightly lower than the scale on the engine oil dipstick. In addition, factors such as the model of the engine oil, season, climate, engine displacement, technical performance, etc. must also be considered.

5

Share

Drive BMW, Ride Mercedes or Drive Mercedes, Ride BMW?

What Causes a Motorcycle to Fail to Shift into Second Gear?

Is it okay to rev the engine in neutral on a motorcycle?

How often should a new motorcycle be inspected?

What is the valve clearance adjustment for Cummins 2.8?

What are the parking techniques for automatic transmission cars?

What type of engine oil does the Honda Lingpai use?

Is the old driver's license collected when renewing it?

Can the Handbrake Be Used as a Brake?

What Certificates Are Needed to Open a Repair Shop?

Is the original driver's license taken back when renewing it?