Does Using China 6 Engine Oil in a China 5 Vehicle Have Any Impact?

How to Clear the Maintenance Reminder on FAW JH6?

Insert the key, just insert it without turning. Press and hold the lever next to the odometer for 5-10 seconds, then turn the key to power on. After another 5-10 seconds, start the engine. Keep holding the lever throughout this process. If the wrench indicator isn't cleared, repeat the same procedure a few more times.

19

5

Share

How to Install the Jiangling Transit Engine Belt?

Loosen the generator fixing screw and the belt tension adjustment screw. Align the ignition marks of the crankshaft and camshaft, place the belt on the crankshaft pulley, and then guide it upwards from the side opposite the tension pulley to place it on the camshaft pulley. Adjust the belt tension to the appropriate level. If it is too loose or too tight, make timely adjustments, then tighten the engine fixing screw and the adjustment screw.

11

5

Share

Where is the Brake Line Located?

The brake line is located underneath the car chassis. Reasons why the brake line is under the car chassis: The parking brake cable usually runs from the handbrake, passes through the chassis, and then reaches the rear wheel brake pads. Therefore, it is generally located underneath the car chassis. It typically acts on the rear wheels, and the line running from the cabin to the rear axle housing under the chassis is the one. This line is distinctly different from electrical wires. Functions of the automotive brake system: To forcibly decelerate or even stop a moving vehicle as required by the driver; To ensure stable parking of a stationary vehicle under various road conditions; To maintain a stable speed for a vehicle driving downhill.

7

0

Share

Will Breaking a Car Window Trigger the Alarm?

Currently, almost all vehicles are equipped with anti-theft devices to prevent theft. Car anti-theft devices can be divided into four main categories: mechanical, electronic, network-based, and fingerprint recognition. Electronic anti-theft devices feature a vibration alarm function, where the vibration caused by striking the window with a safety hammer will trigger the alarm. Below is more related information: 1. Electronic Anti-theft Devices: Also known as computer anti-theft devices, these mainly include card-type, button-type, and remote-control types. These devices control the car's starting, ignition, and other circuits through electronic equipment. When the entire system is activated, any unauthorized movement of the car, opening of doors, fuel tank cap, engine hood, trunk lid, or tampering with the ignition wiring will immediately trigger the alarm, causing lights to flash and sirens to sound. Simultaneously, the starting circuit, ignition circuit, fuel injection circuit, fuel supply circuit, and even the automatic transmission circuit are cut off, rendering the car completely immobilized. These devices are hidden, feature-complete, wireless remote-controlled, and easy to operate, making them widely used in mid-to-high-end cars. 2. Mechanical Anti-theft Devices: These are simple, easy to use, and inexpensive, but they lack an alarm function. Made from metal materials, they include various types of locks such as steering column locks, steering wheel locks, gearshift locks, pedal locks, wheel locks, and car anti-theft magnetic plates. These locks secure the car's operational components, preventing thieves from driving the car away.

13

4

Share

How to turn off the WM Motor vehicle?

Press the brake pedal to ensure the vehicle is stationary, then shift the gear into N (Neutral) position. Engage the parking brake. Shift into P (Park) position, then release the brake pedal. Turn off any unnecessary electrical equipment in the vehicle. Check if the gear is already in P (Park) position, verify that all unnecessary electrical devices are turned off, and ensure the steering wheel is straightened. Turn the key counterclockwise to the end, or press the one-touch start/stop button once, then adjust the ignition switch position to OFF.

20

3

Share

What to Do If Rust Remover Is Sprayed on Brake Pads?

If it hasn't been long, you can wash them with alkaline water, dry them, and then test drive to see if they can still be used. If the brake pads are thin, they should be replaced. The surface must achieve the corresponding friction coefficient. If you don't want to bother, you can leave it as is. After some time of use, the brake will wear it off naturally.

3

0

Share

Does Using China 6 Engine Oil in a China 5 Vehicle Have Any Impact?

How to Clear the Maintenance Reminder on FAW JH6?

How to Install the Jiangling Transit Engine Belt?

Where is the Brake Line Located?

Will Breaking a Car Window Trigger the Alarm?

How to turn off the WM Motor vehicle?

What to Do If Rust Remover Is Sprayed on Brake Pads?

How to Set Up Automatic Locking for Tayron?

What should be paid attention to when changing car engine oil?

How to adjust the height of the T-Roc's high beam?

How are express and slow lanes divided on highways?