Does the Wuling Hongguang Mini have a gasoline version?

What are the symptoms of a damaged stabilizer bar ball joint?

Damage to the stabilizer bar ball joint can cause noise when driving on rough roads, as well as abnormal sounds during driving and braking. The stabilizer bar suppresses body roll: When the left and right wheels of the car pass over different road bumps or potholes, it generates roll resistance to inhibit body roll. Types of stabilizer bars: Front lower control arm stabilizer bar (original equipment), toe adjustment stabilizer bar (original equipment), front shock tower strut bar (commonly known as 'top bar' in Hong Kong and Macau, optional), front crossmember stabilizer bar (commonly known as 'front lower bar', optional), etc.

3

5

Share

What is the solution for a leaking sunroof in a Golf?

The solutions for a leaking sunroof in a Golf are: 1. Replace the sunroof sealing strip; 2. Clean out small sand particles and dust from the sunroof drainage channel; 3. Ensure the sunroof is properly closed; 4. Unclog the drainage pipe. The Golf has the following body dimensions: length 4296 mm, width 1788 mm, height 1471 mm, with a wheelbase of 2631 mm and a fuel tank capacity of 51 liters. The Golf is equipped with a 1.4T direct-injection turbocharged engine, delivering a maximum power of 110 kW at 5000 to 6000 rpm, and a maximum torque of 250 Nm, paired with a 7-speed dual-clutch transmission.

15

5

Share

What is the adjustment method for valve clearance in a single-cylinder diesel engine?

The adjustment method for valve clearance in a single-cylinder diesel engine is as follows: 1. Remove the cylinder head cover when the engine is cold; 2. Rotate the flywheel to align the top dead center mark on the flywheel with the pointer mark on the radiator, positioning the piston at the top dead center of the compression stroke; 3. Measure the clearance between the end of the valve stem and the rocker arm. If a feeler gauge cannot be inserted or there is still a significant gap after insertion, the valve clearance needs to be adjusted; 4. Loosen the lock nut of the valve clearance adjustment screw, turn the adjustment screw, and measure with a feeler gauge until the measured value matches the specified value. While keeping the adjustment screw stationary, tighten the nut.

7

4

Share

Which is better, reversing camera with trajectory or without trajectory?

Reversing camera with trajectory is better. Here are some related introductions about reversing cameras: 1. Introduction to reversing cameras: Reversing cameras, also known as parking assist systems, or reversing visual systems, vehicle monitoring systems, etc. English name: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of reversing cameras: Simple installation. Generally, a single-output reversing camera only requires connecting the positive power wire to the positive terminal of the vehicle's reversing light power, and the negative power wire to the negative terminal of the reversing light or to ground (GND). The wiring can be easily figured out based on the vehicle model, and the camera can be installed in an easy-to-mount position by drilling a hole.

10

2

Share

What do the three colors in the reversing camera represent in terms of distance?

Green indicates a distance of 1 to 3 meters, yellow represents a distance of less than 1 meter, approximately between 60 to 100 centimeters, and when approaching red, the distance is reduced to 60 centimeters. Below is relevant information about the reversing camera: 1. Introduction to the reversing camera: The reversing camera, also known as a parking assist system, or vehicle backup monitoring system, is referred to in English as: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of the reversing camera: Installation is simple; generally, a standard single-output reversing camera only requires connecting the positive power wire to the positive terminal of the vehicle's reversing light power and the negative power wire to the negative terminal of the reversing light or to ground (GND). Wiring can be easily understood with a simple study based on the vehicle model, and the camera can be installed by drilling a hole in an easily accessible position.

15

3

Share

What to Do When the Reversing Camera Changes from Wide Angle to Fisheye?

Just clean it. Below is relevant information about the reversing camera: 1. Introduction to the reversing camera: The reversing camera, also known as a parking assist system, reversing visual system, or vehicle monitoring system, is referred to in English as: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. 2. Advantages of the reversing camera: Simple installation. Generally, a standard single-output reversing camera only requires connecting the positive power wire to the positive terminal of the car's reversing light power and the negative power wire to the negative terminal of the reversing light or to ground (GND). The wiring can be easily figured out based on the vehicle model, and the camera can be installed by drilling a hole in an easily accessible position.

20

5

Share

Does the Wuling Hongguang Mini have a gasoline version?

What are the symptoms of a damaged stabilizer bar ball joint?

What is the solution for a leaking sunroof in a Golf?

What is the adjustment method for valve clearance in a single-cylinder diesel engine?

Which is better, reversing camera with trajectory or without trajectory?

What do the three colors in the reversing camera represent in terms of distance?

What to Do When the Reversing Camera Changes from Wide Angle to Fisheye?

How to Clear the Yellow Engine Light?

Is it possible to buy a used car with a title but without transferring ownership?

Where to Check the Vehicle Identification Number in a Car?

Why is the Magotan so noisy?