Does the vehicle annual inspection due on August 8th mean it can be done until the end of August?

1 Answers
DiNora
07/29/25 7:48pm
The vehicle annual inspection due on August 8th can be performed until the end of August, meaning the entire month of August is available for the annual inspection. Below are specific details about motor vehicle annual inspections: 1. Inspection Categories: Annual inspection refers to the safety examination of vehicles conducted yearly or biennially, which includes a comprehensive check of components such as the horn, brakes, axle weight, chassis, ignition system, lighting system, exhaust system, license plate installation, etc. 2. Precautions: Before the annual inspection, it is essential to check if the vehicle has any outstanding traffic violations. If there are any, they must be resolved before proceeding with the annual inspection. Otherwise, the inspection cannot be completed if violations remain unresolved.
Was this review help?
8
1
Share
More Forum Discussions

What Subjects Are Tested in Driving License Subject 2?

There are five items in the driving school Subject 2 test, which are: 1. Hill start and fixed-point parking. 2. Parallel parking. 3. Curve driving. 4. Right-angle turn. 5. Reverse parking into a garage and parallel parking. Introduction to common point deductions in Subject 2: 1. Not wearing a seatbelt deducts 100 points. 2. Not closing the car door properly deducts 100 points. 3. Not using the turn signal during hill start deducts 10 points. 4. Not using the turn signal when exiting parallel parking deducts 10 points, and stalling once deducts 10 points. Here is a detailed introduction to the test items: 1. Hill fixed-point parking involves stopping the car on a slope, pulling the handbrake to prevent rolling back, then starting and accelerating on the slope, and passing through the slope. 2. Parallel parking requires driving the vehicle to a position parallel to the garage in the forward direction, then reversing into the garage to the right rear without any pauses. As long as the vehicle is parked within the designated area without crossing the boundary lines, it is considered a pass.
10
4
Share

What are the components of xenon headlights?

Xenon headlights consist of the following components: 1. Bulb: Without filaments, it generates brightness by creating an electric current between electrodes to stimulate xenon molecule collisions. 2. Electronic ballast: Uses the 12V DC voltage from the battery to produce a high-voltage ignition for the bulb. 3. Wiring control box: Made of flame-retardant materials, it enhances current-carrying capacity by increasing the cross-sectional area of the power wires. Xenon headlights refer to lamps filled with a mixture of inert gases, including xenon, also known as metal halide lamps or xenon headlights. They are categorized into automotive xenon headlights and outdoor lighting xenon headlights. The working principle of xenon headlights is as follows: 1. Inside an anti-UV crystal quartz glass tube, various chemical gases are filled, and a booster instantly increases the vehicle's 12-volt DC voltage to 23,000 volts. 2. High-voltage amplitude excites the free electrons of xenon inside the quartz tube, generating a light source between the two electrodes.
5
2
Share

What to Do If Your Driver's License Has Expired for Inspection?

If your driver's license inspection has expired for less than one year, you can normally renew it and undergo inspection. If it has been expired for more than one year, you will need to retake the tests. Only after passing the tests can you regain your driver's license. Below are the relevant details: 1. Article 35 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" states that motor vehicle drivers should apply for renewal at the vehicle management office where the license was issued within 90 days before the expiration of the driver's license. 2. If a driver fails to renew the license for more than one year after its expiration, the vehicle management office shall revoke the driver's license. If the revocation period does not exceed two years, the driver can regain driving privileges after passing the road traffic safety laws, regulations, and related knowledge tests.
14
4
Share

What are the symptoms of a faulty RPM sensor?

Engine sensor failure symptoms include: 1. Unstable engine idle; 2. Momentary stalling or engine shutdown when starting or decelerating to stop; 3. Reduced engine acceleration performance; 4. Deviation in the speed display on the instrument panel; 5. Illumination of the engine warning light. Sensors are typically installed on the distributor or engine, detecting crankshaft rotation angle. Failure disrupts the ignition system, preventing engine operation. Most RPM sensors are magnetic pulse type, generating weak electrical signals that can be tested using a multimeter or oscilloscope.
9
0
Share

What are the reasons why the Kia K5 won't start?

The reasons why the Kia K5 won't start are: 1. The car battery is low on power. 2. Low temperature causes the viscosity and rotation speed of the car engine oil to decrease. 3. There is an issue with the ignition system. 4. Insufficient fuel in the car. 5. Excessive carbon deposits inside the vehicle's engine. 6. The fuel pump is damaged, preventing fuel from the fuel tank from being supplied for combustion. Taking the 2020 Kia K5 as an example, here is its introduction: 1. The front suspension of the 2020 Kia K5 is a MacPherson independent suspension, and the rear suspension is a multi-link independent suspension. 2. The 2020 Kia K5 is equipped with a 1.5L inline 4-cylinder turbocharged engine, with a maximum horsepower of 170ps, a maximum power of 125kw, a maximum torque of 253nm, and is paired with a 7-speed dual-clutch transmission.
16
5
Share

What does the mode button in a car mean?

Mode button in a car is commonly found on the multifunction steering wheel and the center console. When the mode button is on the multifunction steering wheel, it is used to switch between different multimedia modes, such as FM radio, AM radio, CD, or USB. When the mode button is on the center console, it is used to switch between different air conditioning vent modes, typically cycling through foot-level vents, head-level vents, and windshield defrost modes. Other common buttons in a car include: RES to resume or increase cruise control speed, CANCEL to exit cruise control, and SET to set or decrease cruise control speed.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.