Does the Skoda Rapid meet China 6 emission standards?

1 Answers
McEvangeline
07/29/25 4:46pm
Skoda Rapid meets China 6 emission standards. The Skoda Rapid is a brand-new crossover travel car under the Skoda brand, equipped with a 1.5L naturally aspirated engine across the entire lineup. It delivers a maximum power of 82kW and a maximum torque of 145Nm, with the maximum power achieved at 6100 rpm and the maximum torque at 4000 rpm. The 1.5L naturally aspirated engine features multi-point fuel injection technology and utilizes an aluminum alloy cylinder head and block. This engine is paired with either a 5-speed manual transmission or a 6-speed automatic transmission. The front suspension of the Skoda Rapid employs a MacPherson strut independent suspension, while the rear suspension uses a torsion beam non-independent suspension. This compact suspension system helps reduce production costs while also expanding trunk space and rear passenger space.
Was this review help?
19
4
Share
More Forum Discussions

How to Replace the Wiper Blades on a Volkswagen Tiguan?

After turning off the vehicle, do not remove the key immediately. Within 3 seconds, pull the wiper control lever inward, and the wiper blades will move to the maintenance position. Apply slight force to pull the wiper blade toward the front of the car. When pulled to a certain position, it will lock firmly in place. Press the silver button on the wiper arm, hold the wiper blade with your hand, and gently pull it outward to remove the old rubber strip. When installing the new rubber strip, remember to stagger the two metal pieces and ensure it is inserted into the first groove. Once the rubber strip is successfully installed, follow the reverse steps of the removal process to complete the wiper blade installation.
10
4
Share

How to Check the Tire Pressure of All Four Tires on the Oshan X5?

First, press the car's brake pedal, then press the one-button start button to start the car's engine. All the lights on the dashboard will illuminate, confirming that the vehicle's electronic systems are powered on. You can then check the tire pressure of all four tires on the dashboard. If any tire pressure is abnormal, you can proceed to inflate it. Once all four tire pressures are normal, you can press the tire pressure reset button to clear the tire pressure warning. The tire pressure warning light alerts the driver to check the tire pressure. At this point, you should not continue driving and must stop immediately to inspect and repair the tires.
9
2
Share

How to Sew a Car Steering Wheel Cover?

First, fit the upper part of the steering wheel cover, ensuring the seam is positioned at the most accurate point. To prevent slipping during sewing, secure it with tape. Measuring the steering wheel helps avoid issues like loose threads or gaps, as the steering wheel cover cannot be sewn with just a single thread. Pass the needle through the inner thread of the steering wheel cover and pull it tight, then proceed to sew the next stitch. When reaching the end, pass the needle through the inner thread again and continue sewing. Repeat this process until the entire cover is hand-sewn.
15
0
Share

How to Pair Tesla Phone Key?

Download the Tesla mobile app to your phone and log in to the Tesla mobile app with your username and password. To authenticate your phone or use it as a key, the phone must be turned on and Bluetooth must be enabled. Make sure 'Allow Phone Access' is enabled. In the Tesla mobile app, tap on Phone Key, then tap Start to begin searching. The mobile app will prompt you to tap the key card. Tap the key card against the card reader. The mobile app will confirm that your phone has been successfully authenticated and paired.
1
1
Share

How to Solve Car Key Battery Leakage?

Use a small hex screwdriver to remove the screws on the back cover of the remote key. Then take off the back cover of the remote key to reveal the circuit board inside. Use a low-power hair dryer to dry the circuit board, or use a multimeter to check if the circuit is functioning properly and whether the electronic component pins need to be re-soldered. If the leakage time is short and the circuit board is not damaged, you can install a new battery and reassemble the key for reuse.
9
2
Share

How to Take the Driving Test?

You can register at any regular driving school, then undergo a physical examination to check the applicant's hearing, vision, color blindness (especially red-green color blindness), etc. The test content usually includes traffic regulations and driving knowledge. New items in Subject 2 test: reversing into a garage, parallel parking, starting and stopping on a slope, S-curve driving, and right-angle turns. You need to master the basics of the clutch, brake, and accelerator. After passing Subject 3, there is also Subject 4, which tests the basics of safe and civilized driving. After passing all subjects, wait for half an hour at the test center to receive your driver's license.
16
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.