···
Log in / Register

Does the Old Excelle's Engine Oil Leak Need Repair?

4 Answers
LaLuna
07/30/25 2:08am
If the Old Excelle's engine is leaking oil, it is necessary to promptly take it to a 4S shop for inspection and repair. 1. Introduction: An engine (Engine) is a machine that can convert other forms of energy into mechanical energy. Engines can be used as power generation devices or refer to the entire machine including the power device (such as gasoline engines, aircraft engines). 2. Classification: Engines include internal combustion engines (reciprocating piston engines), external combustion engines (Stirling engines, steam engines, etc.), jet engines, electric motors, etc. Among them, the valve drive mechanism adopts a hydraulic support ball rocker arm structure. Compared with the hydraulic tappet valve drive mechanism commonly used in current gasoline engines, this novel valve drive mechanism has the advantage of relatively small friction torque, thus requiring less driving force, which can effectively reduce engine power consumption and fuel consumption.
Was this review help?
6
0
Share
LaElle
08/15/25 8:08am
When I drove my 2008 Excelle last year, I also encountered oil pan leakage. I suggest you assess the situation. If the valve cover gasket is leaking severely and oil drips onto the exhaust pipe, it's dangerous and you need to replace the gasket immediately. If it's just slight oil seepage due to aging oil pan sealant, temporary repair may not be necessary, but you should check the oil level weekly by opening the hood. Remember to clean the oil sludge in the engine compartment – mechanics say the areas covered by sludge actually leak the most. Prolonged oil leakage can corrode rubber parts of wiring harnesses, making repairs more expensive. It's better to spend a few hundred yuan to replace the gasket sooner rather than later.
Was this review help?
3
5
Share
Expand All
VonLydia
10/21/25 4:29am
My old Buick Excelle with 130,000 km just had its oil leak fixed last month. The crankshaft rear oil seal was leaking so badly that the dashboard warning light came on, and it cost me 3,800 RMB to fix, which required lifting the engine. If you see oil stains on the subframe or oil spots in the parking space, first clean them and use an oil test strip on the leak point, then check the leakage rate after three days. The repair shop owner taught me this trick: if it leaks more than a coin-sized amount daily, it must be repaired immediately, or it could lead to cylinder scoring; if it's just the valve cover gasket seeping, you can monitor it, but top up the oil every two weeks. Rubber component aging is a common issue with this car.
Was this review help?
2
4
Share
Expand All
DeDylan
12/04/25 4:57am
The location of oil seepage is crucial! A clogged crankcase ventilation valve can cause high pressure and oil seepage, which can be fixed by replacing the valve body yourself for just 60 yuan. If the valve cover gasket is aging and leaking onto the ignition coils, it must be replaced to avoid cylinder misfire. I once experienced oil dripping onto the generator pulley, causing slippage and sudden air conditioning failure, which was very dangerous. Now, I always keep engine cleaner in my car; when I spot new oil stains, I spray and clean to identify the source. Be wary of repair shop quotes: charging over 800 yuan for replacing a valve cover gasket including labor is a rip-off, as genuine rubber parts cost just around a hundred yuan.
Was this review help?
12
0
Share
Expand All
More Forum Discussions

How Often Should Honda Transmission Fluid Be Changed?

When a Honda reaches approximately 40,000-60,000 kilometers in mileage or has been in use for about 2 years, it is necessary to change the vehicle's transmission fluid. However, the specific replacement interval should be determined based on the owner's driving frequency and habits. Below is relevant information: 1. Replacement Methods: When changing the transmission fluid, owners can choose between two methods—gravity drain and flush or machine-assisted fluid exchange. 2. Before replacing the fluid: The old transmission fluid must be completely drained, and the container should be thoroughly cleaned before adding new fluid. 3. If choosing the gravity drain method: First, loosen the drain plug at the bottom of the vehicle to allow the old fluid to drain out by gravity. After cleaning, new fluid can be added. The most direct advantage of this method is the simplicity of the entire process; however, the biggest drawback is that it cannot fully remove all the old fluid, leaving residual fluid inside the container.
9
2
Share

Why Does the Lavida Transmission Jerk?

The reasons for the Lavida transmission jerking include torque converter failure and transmission oil pump failure. Torque Converter Failure: Power transmission in the torque converter is interrupted, meaning there is no driving response when the torque converter engages any gear. This phenomenon is usually caused by two reasons: First, there is no working fluid in the torque converter. Since there is no mechanical connection between the pump wheel and the turbine in the torque converter, power is transmitted through the fluid as a medium. Without fluid, power naturally cannot be transmitted. Second, the turbine is loosened or stuck with the turbine shaft. Transmission Oil Pump Failure: Intake system leakage, excessively lean air-fuel mixture; incorrect timing, improper ignition advance angle; throttle position sensor or air flow meter failure; low fuel pressure; injector malfunction.
3
4
Share

Where is the ABS fuse located in the Mercedes-Benz B200?

The fuse box for the Mercedes-Benz B200 circuit is located under the hood, in the engine compartment, next to the battery. Fuse Overview: Automotive fuses are a type of current fuse. When the circuit current exceeds twice the rated current of the fuse, it will blow within seconds to protect the circuit. They are commonly used for overcurrent protection in automotive circuits and also for industrial equipment. Fuse Classification: Fuses can be divided into: mini blade fuses, small automotive fuses, medium automotive fuses, and large automotive fuses. The rated current ranges from 1-40 amperes (A) to large fuses of 30-120 amperes (A), with a rated voltage of 32 volts (V).
12
0
Share

What Causes the Noise When Starting a GAC Trumpchi?

GAC Trumpchi starting with noise is due to brake noise, especially for new cars or newly replaced brake pads. The brake discs and pads need to break in, and noise is quite common. Brake Principle: The working principle of brakes mainly comes from friction. By utilizing the friction between the brake pads and brake discs (or drums), as well as between the tires and the ground, the kinetic energy of the moving vehicle is converted into heat energy through friction, bringing the car to a stop. A good and efficient braking system must provide stable, sufficient, and controllable braking force, along with excellent hydraulic transmission and heat dissipation capabilities. This ensures that the force applied by the driver on the brake pedal is effectively transmitted to the master cylinder and each wheel cylinder, while avoiding hydraulic failure and brake fade caused by excessive heat. Maintenance Methods: Under normal driving conditions, inspect the brake shoes every 5,000 kilometers. Not only should the remaining thickness be checked, but also the wear state of the shoes, whether the wear on both sides is even, and whether they return freely. Any abnormal conditions must be addressed immediately.
11
5
Share

Why does the front left wheel of the Geely Geometry C make abnormal noises when passing over bumps?

The reason why the front left wheel of the Geely Geometry C makes abnormal noises when passing over bumps is due to deformation of the subframe. Effects of subframe deformation: Minor deformation of the subframe is a relatively serious issue. If the subframe is deformed, the wheel alignment data will be affected, which in turn impacts the vehicle's handling and driving stability. Function of the subframe: The subframe can be considered as the skeleton of the front and rear axles, forming part of their structure. The subframe is not a complete chassis but rather a bracket that supports the front and rear axles and suspension, connecting them to the "main frame," hence commonly referred to as the "subframe." The purpose of the subframe is to block vibrations and noise, reducing their direct transmission into the cabin. Therefore, subframes are mostly found in luxury sedans and SUVs, with some vehicles even equipping subframes for the engine. In traditional unibody designs without subframes, the suspension is directly connected to the body panels.
1
0
Share

What is the appropriate tire pressure for the Macan?

According to the international GBT2978-2008 standard, the tire pressure for different Macan tires is as follows: Standard tires: 2.4-2.5 bar; Reinforced tires: 2.8-2.9 bar; Maximum pressure: should not exceed 3.5 bar. Tire pressure, strictly speaking, refers to the air pressure inside the tire. Normal tire pressure in winter: In winter, the tire pressure should be based on the standard tire pressure of the car, with an appropriate increase of about 0.2 bar. Normal tire pressure in summer: Generally, the lower limit of the standard tire pressure is sufficient. For example, the lower limit for standard tires is 2.4 bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1 bar lower than the standard to avoid tire blowouts due to high temperatures.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.