Does the Lynk & Co 03+ have 200 horsepower in its factory state?

Is There a Scrap Age Limit for Small Cars?

For household 5-seat sedans and 7-seat SUVs, non-commercial small and mini vehicles have no usage age limit. When the normal mileage reaches 600,000 kilometers, the state will guide them to be scrapped. In addition to the above vehicles, small and mini non-commercial passenger vehicles, large non-commercial sedans, and wheeled special machinery vehicles also have no usage age limit. Commercial vehicles have scrap age limits as follows: Small and mini taxi passenger vehicles have a scrap age limit of 8 years, medium-sized taxi passenger vehicles have a limit of 10 years, and large taxi passenger vehicles have a limit of 12 years. Bus passenger vehicles have a scrap age limit of 13 years, other small and mini commercial passenger vehicles have a limit of 10 years, and large and medium-sized commercial passenger vehicles have a limit of 15 years. Mini commercial trucks have a scrap age limit of 8 years, light and large commercial trucks have a limit of 10 years. The vehicle scrapping process is as follows: The car owner applying for scrapping and renewal should fill out the "Motor Vehicle Change, Transfer, Modification, Suspension, Scrapping Approval Application Form" in duplicate and stamp the owner's seal. The registration desk accepts the application and issues a "Vehicle Scrapping Notice" for vehicles that have reached the scrap age. For vehicles that have not reached the scrap age, after inspection and confirmation by the motor vehicle inspection desk that they meet the scrapping standards, a "Vehicle Scrapping Notice" is issued. The owner chooses a qualified recycling company to dismantle the vehicle with the "Notice". The recycling company dismantles the vehicle and takes photos after verifying the "Notice". The engine must be separated from the vehicle, the engine block must be broken, and the frame (chassis) must be cut. The owner submits the "Change Form", "XX Province Vehicle Renewal Technical Appraisal Form", "Scrapped Vehicle Recycling Certificate", and vehicle dismantling photos to the motor vehicle inspection desk for verification and signature. The license plates are reclaimed, and the scrapping registration is processed after approval according to regulations. Special Notes: According to Article 30 of the "Motor Vehicle Registration Regulations", if the vehicle cannot be driven back to the registration location due to damage, the owner can sell the scrapped vehicle to a local motor vehicle recycling company. Commercial vehicles converted to non-commercial use must be scrapped according to the original commercial vehicle's scrapping time. According to Article 43 of the "Motor Vehicle Registration Regulations", after completing the transfer or cancellation of motor vehicle registration, the original owner can apply to the vehicle management office to use the original license plate number when registering a newly purchased vehicle. The application must meet the following conditions: (1) The application is submitted within six months after the transfer or cancellation; (2) The owner has owned the original vehicle for more than three years.

5

2

Share

Can Motorcycles Select License Plates Online?

Motorcycles can select license plates online. Plate selection rules: When registering a motorcycle, a set of computer-randomized license plate numbers is generated. The owner can choose their preferred motorcycle plate from this random set. Lucky riders might find their desired plate number in this random selection, but note that there is only one opportunity. Plate replacement conditions: It is important to note that motorcycles, as motor vehicles, have the same right as cars to change license plates, but certain conditions must be met. First, the owner must have two motorcycles under their name before applying to swap the license plates between them. Important notes: Applicants must ensure the accuracy of information such as the certificate number, vehicle identification number, unified sales invoice of the motor vehicle, and contact details. If the entered information does not meet the requirements, the pre-selected license plate number will be canceled.

19

5

Share

Is the left turn signal activated by pushing up or down?

The left turn signal is activated by pushing down. Usage Tips: Users must remember the principle of 'up for right, down for left'. It's quite simple - just imagine the turn signal lever as a steering wheel, and push it in the direction you want to turn. The 'up-right, down-left' configuration follows conventional habits: downward represents counterclockwise, which most people associate with left turns, while upward represents clockwise, commonly understood as right turns. Usage Rules: When observing the need to change lanes ahead, drivers should activate the turn signal in advance, typically at a distance of approximately 50 meters or more. After turning on the signal, immediately check the rearview mirror to ensure safe lane changing. Important Notes: When making a left turn at signal-controlled intersections, motor vehicles must activate the turn signal and use low beams when driving at night. When following another vehicle in the same direction at close range, high beams should not be used. When passing through sharp curves, slopes, arched bridges, crosswalks, or uncontrolled intersections at night, vehicles should alternately flash their high and low beams as a warning.

16

5

Share

Should You Downshift When Braking in a Manual Car?

Manual cars require downshifting when braking to continue driving. Downshifting timing on flat roads: For example, when driving at 60 km/h in 4th gear and noticing a red light at an intersection, immediately brake to decelerate. If the vehicle ahead has already stopped, downshifting is unnecessary; simply control the brake to let the car coast to a stop. If after decelerating, you need to follow the slow-moving traffic ahead, then shifting to a lower gear is required. Without downshifting, the original 4th gear would make it impossible to follow the traffic after deceleration. If the light turns green just after decelerating and the road ahead is clear, with the engine RPM still around 1500, you can directly press the accelerator to proceed. However, if the engine RPM has dropped to around 1000, you must downshift one gear to smoothly accelerate forward. Downshifting timing when descending: The above scenarios are based on flat roads. When descending a slope, if the engine RPM is above 1000, you can directly downshift one gear and then accelerate to proceed.

7

0

Share

What parts need to be replaced for a motorcycle burning oil?

For a motorcycle burning oil, you need to replace the cylinder block, piston, piston rings, and valve stem seals. Reasons for burning oil: Motorcycle burning oil occurs when engine oil enters the combustion chamber, leading to reduced oil levels and potentially causing more severe engine damage. Apart from poor sealing between the cylinder block and piston rings, aged valve stem seals can also allow oil to be drawn into the combustion chamber during engine intake. Solutions for burning oil: Conduct a thorough inspection of the entire oil lubrication system, remove carbon deposits from combustion residues, ensure unobstructed intake and exhaust valves, replace aged or damaged valve stem seals and crankshaft seals, and finally, reduce the clearance between engine cylinder blocks to maintain proper engine temperature.

2

1

Share

Why Are There Many Small Bubbles in Transmission Fluid?

Transmission fluid contains bubbles due to either excessively high or low fluid levels. When the fluid level is too high, planetary gears and other rotating components partially submerge in the transmission fluid, causing agitation and leading to bubble formation. Conversely, if the fluid level is too low, the oil pump may draw in air, mixing it with the fluid and generating bubbles. If these bubbles enter the hydraulic control system, the system's pressure may drop, affecting the transmission's normal operation and potentially causing slippage. Additionally, bubbles can cause the fluid level to rise, leading to overflow through the transmission vent or filler hole, which may result in misdiagnosis. Signs that indicate the need for transmission fluid replacement include: vehicle shaking, rough gear shifting; transmission overheating warning on the dashboard; engine stalling; and unusual noises. The methods for replacing transmission fluid are as follows: 1. Loosen the drain plug at the bottom of the transmission to drain the old fluid before refilling. 2. Remove the transmission oil pan directly for draining and refilling: This method is more thorough than the previous one, as it allows for the removal of debris from the bottom of the oil pan. 3. Use a circulation machine to replace automatic transmission fluid: Dynamic fluid replacement with an intelligent circulation machine can filter and clean sludge and impurities inside the automatic transmission. Hazards of not changing transmission fluid for an extended period: 1. Damage to the transmission's shift control mechanism; 2. Abnormal wear of gears and clutch plates inside the transmission; 3. Impaired transmission operation, leading to valve body damage.

13

0

Share

Does the Lynk & Co 03+ have 200 horsepower in its factory state?

Is There a Scrap Age Limit for Small Cars?

Can Motorcycles Select License Plates Online?

Is the left turn signal activated by pushing up or down?

Should You Downshift When Braking in a Manual Car?

What parts need to be replaced for a motorcycle burning oil?

Why Are There Many Small Bubbles in Transmission Fluid?

What is the distance for ramp positioning?

Do I Need to Drive the Motorcycle for Annual Inspection?

Is It Dangerous When Motorcycle Tires Wear Down to the Steel Wires?

Can You Make a U-Turn When Turning Left?