Does the Jetta VS5 have child locks?

1 Answers
Amara
07/29/25 9:00pm
Jetta VS5 has child locks. They are located on the edge of the rear doors. Introduction to Child Locks: Car child locks, also known as child safety door locks, are installed on the rear door locks. After opening the rear door, there is a small lever (safety mechanism) below the door lock. Move the lever toward the end with the child icon, then close the door. At this point, the door cannot be opened from the inside and can only be opened from the outside. Function of Child Locks: When children are seated in the rear seats, child locks can prevent active and unaware children from opening the door during driving, thereby avoiding danger. In this case, the door can only be opened from the outside by an adult after the car has stopped.
Was this review help?
15
4
Share
More Forum Discussions

How to Count the Two Right Lanes?

Right two lanes refer to the second and third lanes counting from left to right. Driving in the right two lanes means using either of the two rightmost lanes. Assuming there are three lanes in total, counting from right to left, the third lane (leftmost lane) is marked for left turns only. Once entering this lane, vehicles can only turn left, not proceed straight or turn right. Lanes one and two both allow straight driving. When needing to go straight, navigation software will announce "please take the right two lanes". According to China's Road Traffic Safety Implementation Regulations, on a three-lane highway, the speed limit for the second lane is 100-80 km/h, while the rightmost third lane has a limit of 80-60 km/h. When navigation gives such prompts, it usually indicates the highway exit is approaching, requiring drivers to slow down and prepare to exit. Driving in the right two lanes also makes exiting the highway more convenient.
15
0
Share

What are the reasons for no response from the car after jump-starting?

There are two reasons for no response from the car after jump-starting: one is that the battery terminal clamps have come loose, and the other is that the battery is completely drained. The principle of jump-starting a car: It involves using an external device to transfer the stored electricity from another vehicle's battery to the car with a depleted battery, which is then used to start the vehicle. Once the car starts normally, the external device can be removed, allowing the car's charging system to restore the battery's charge. Causes of battery depletion: This usually occurs due to poor usage habits during regular vehicle operation. Specifically, turning on the headlights or ignition switch without first starting the engine can cause the car battery to drain rapidly.
16
1
Share

How to Check Engine Oil?

Checking the engine oil level involves fully inserting the oil dipstick into the oil pan, then pulling it out to examine the oil traces on the dipstick. Here's relevant information about engine oil: 1. Functions of engine oil: It separates relatively sliding component surfaces to reduce wear; carries heat back to the oil tank and dissipates it into the air to assist the radiator in cooling the engine. 2. Replacement interval: Engine oil should be changed every 6 months or 5,000 kilometers. Engine oil is the lubricant used in engines, composed of base oil and additives. It serves multiple purposes including lubrication and wear reduction, auxiliary cooling, sealing against leaks, rust and corrosion prevention, as well as shock absorption.
20
2
Share

What are the testing standards for steam turbine lubricating oil?

The following are the standards for steam turbine lubricating oil: 1. In China, the standardized steam turbine lubricating oils include L-TSA (anti-oxidation and anti-rust) steam turbine lubricating oil, with the standard GB11120-89; 2. Anti-ammonia steam turbine lubricating oil, with the standard SH0362-92; and rust-proof steam turbine lubricating oil for naval use, with the national military standard GJB1601A-98. The following are the essential requirements for steam turbine lubricating oil: 1. Good oxidation stability; 2. Appropriate viscosity and good viscosity-temperature characteristics; 3. Good demulsibility; 4. Good rust and corrosion prevention; 5. Good foam resistance and air release properties.
9
2
Share

What Causes Unstable Idle Speed and Stalling in Motorcycles?

Motorcycle idle speed instability and stalling can be attributed to two main causes: either a malfunction in the intake system or a fault in the sensors related to the intake system. Regular Oil Changes: For motorcycles, the most crucial maintenance task is changing the engine oil. Engine oil is often referred to as the lifeblood of the engine. Without oil, the engine cannot operate properly. Inside the engine, oil serves multiple functions including lubrication, cleaning, sealing, shock absorption, and rust prevention. Over time, the performance of engine oil deteriorates, making regular oil changes essential. Replacing the Oil Filter: Every time you change the engine oil, the oil filter should also be replaced. The oil filter is responsible for filtering impurities from the oil. Without a functioning oil filter, the oil would become excessively dirty after some use, which could negatively impact engine lubrication.
10
5
Share

What Causes Oil Leakage in the Torque Converter?

The cause of oil leakage in the torque converter may be due to assembly process issues or deformation of a certain component. Function of the Torque Converter: The torque converter serves to transmit torque, change torque, shift gears, and act as a clutch. It is typically installed between the engine power unit and the transmission, with ATF (Automatic Transmission Fluid) hydraulic pressure acting as the working medium. It helps transfer engine power to the gears, thereby reducing the impact force experienced during gear shifts. This is very similar to the semi-engaged state of a manual transmission clutch. Moreover, when the rotational speed reaches a certain level, the torque converter automatically locks. Introduction to the Torque Converter: The torque converter, also known as the hydraulic torque converter, is a component in automatic transmissions designed to assist the engine flywheel in transmitting power. It directly replaces the traditional clutch in manual transmissions and consists of three hydraulic elements: the impeller (pump), turbine, and stator. As a non-rigid torque converter that operates using fluid as the medium, it transmits power in liquid form. It includes a sealed working chamber where the fluid circulates continuously. The impeller, turbine, and stator are each connected to the input shaft, output shaft, and housing, respectively, to perform their functions.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.