Does the Harley X48 have ABS?

1 Answers
GageDella
07/29/25 4:42pm
Harley X48 has ABS. The ABS sensor is located on the inner side of the car tire, which can be seen by lifting the car. ABS, the full name is Anti-lock Braking System (Antilock Brake System). Its function is to automatically control the braking force of the brake during car braking, so that the wheels are not locked and remain in a state of rolling and sliding (the slip rate is about 20%), to ensure that the adhesion between the wheels and the ground is at its maximum. Working principle: During braking, ABS quickly determines the locking state of the wheels based on the speed signals from each wheel speed sensor, closes the normally open input solenoid valve on the wheel that is starting to lock, and keeps the braking force unchanged. If the wheel continues to lock, the normally closed output solenoid valve is opened, and the braking pressure on this wheel rapidly decreases due to the direct connection to the brake fluid reservoir, preventing the wheel from being completely locked due to excessive braking force. This keeps the braking state always at the optimal point (slip rate S is 20%), achieving the best braking effect and the safest driving.
Was this review help?
14
4
Share
More Forum Discussions

What Causes Abnormal Noise in the Engine Water Pump?

Reasons for abnormal noise in the engine water pump: 1. Damaged water pump bearing; 2. Broken fan blades in the water pump, where high-velocity water flow drives the detached blades to collide; 3. Overheating of the water pump. The self-priming pump is a type of self-priming centrifugal pump, featuring a compact structure, easy operation, stable performance, simple maintenance, high efficiency, long lifespan, and strong self-priming capability. Working principle of the water pump: Before starting the pump, fill the pump casing with water or ensure the casing already contains water. Upon starting, the impeller rotates at high speed, directing the water in the impeller channels toward the volute. This creates a vacuum at the inlet, opening the check valve and allowing air from the suction pipe to enter the pump, then flowing through the impeller channels to the outer edge.
4
5
Share

Do You Need to Press the Accelerator When Reversing?

Whether you need to press the accelerator when reversing depends on the actual situation. For example, on a slope, the car may not move without pressing the accelerator, in which case it is certainly necessary to press it. However, in most cases, you do not need to press the accelerator and can rely mainly on idle speed, especially for beginners—it is recommended not to press the accelerator if possible. When you do press the accelerator, it must be done lightly; avoid pressing it hard. This is primarily for safety reasons, as reversing makes it difficult to see what's behind in time, and pressing the accelerator hard in such situations can easily lead to accidents. When reversing, frequently check the side mirrors and the rearview mirror inside the car to ensure there are no obstacles around the vehicle before proceeding, to ensure safety.
6
2
Share

What is the difference between Ford ST and RS?

The differences between Ford ST and RS: 1. Different appearance: The Ford ST uses a large number of black components on the front of the car, grille, etc., and is equipped with dual-color 18-inch wheels, a sport bumper, and a rear spoiler; the RS is equipped with an aerodynamic kit all over the body, and the huge black spoiler at the rear gives a strong visual impact. 2. Different engines: The Ford ST is equipped with a 1.5T three-cylinder turbocharged engine; the RS is equipped with a 2.3T engine. 3. Different power: The Ford ST has a maximum power of 250 kW and a peak torque of 345 Nm, matched with a 6-speed manual transmission, but does not come with an all-wheel drive system; the RS has a maximum power of 350 kW and a peak torque of 440 Nm, with the transmission system matched to a 6-speed manual transmission, and comes standard with an all-wheel drive system, using 19-inch wheels.
12
5
Share

How to reset the maintenance light of the 2018 Haval H6?

The method to reset the maintenance light of the 2018 Haval H6: 1. Turn on the ignition switch; 2. When the OIL interface appears on the instrument display, press and hold the MODE button for about 5 seconds; 3. After the OIL symbol on the instrument display starts flashing, quickly press the MODE button 5 times or more; 4. Once the OIL symbol stops flashing and turns off, the maintenance reset is complete. The body dimensions of the 2018 Haval H6 are 4610mm, 1860mm, and 1720mm respectively, with a wheelbase of 2680mm. It is equipped with 235/55R19 tires, paired with multi-spoke aluminum alloy wheels. The tire width and size are excellent, consistent with the current model.
5
4
Share

Do Hybrid Cars Need Charging?

Hybrid cars do not require charging and operate just like conventional vehicles. These vehicles harness energy that would otherwise be wasted in traditional cars, storing it as electrical energy. The hybrid system works by using part of the engine's power to generate electricity and store it in the battery when high engine output is not needed. The stored electrical energy is then efficiently utilized as driving force during vehicle operation, reducing fuel consumption while enhancing performance. Essentially, electricity circulates within the hybrid dual-power system, enabling hybrid vehicles to use electric power without external charging.
17
0
Share

What is the hybrid principle of the Camry?

The hybrid principle of the Camry is a series-parallel type, which is one of the various transmission systems in hybrid vehicles. In the series-parallel power coupling mechanism, the motor MG1 and the engine need to undergo planetary gear speed coupling. After speed coupling, torque coupling with motor MG1 is also required. Through speed synthesis, motor MG2 achieves speed regulation of the engine, making the engine speed independent of the vehicle speed, thereby realizing the ECVT function. The Camry's body dimensions are 4900mm, 1840mm, and 1455mm, with a wheelbase of 2825mm. The all-new Camry is built on the new TNGA platform and is equipped with three powertrains: TNGA 2.5L HEV, TNGA 2.5L, and TNGA 2.0L.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.