Does the 10th-generation Civic have a rear anti-collision beam?

What is the replacement interval for spark plugs?

Spark plug replacement interval: Under normal maintenance conditions, replacement is recommended after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type. It is advisable to follow the instructions in the user manual. The following standards can be referenced for maintenance and replacement: Platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Methods to determine if a spark plug is damaged: Remove the spark plug and observe its appearance to assess its condition. A normal spark plug will have an insulator skirt and electrodes that appear gray-white, gray-yellow, or light brown. A properly functioning spark plug will have a reddish-brown insulator skirt, with an electrode gap between 0.8-0.9mm and no signs of electrode burn. If the spark plug is contaminated with oil or deposits but is not damaged, it can continue to be used after cleaning off the oil and deposits. If the spark plug is severely damaged, showing signs such as blistering at the tip, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plug with a new one. Additionally, if the spark plug appears black as if smoked, it indicates that the wrong heat range was selected or that the air-fuel mixture is too rich, or that engine oil is leaking into the combustion chamber.

3

5

Share

Should You Depress the Clutch When Turning?

Generally, you do not need to depress the clutch when turning or making a U-turn. Here are the specific details: 1. Vehicle deceleration is primarily achieved through the service brake, i.e., the foot brake. The clutch is only depressed when the vehicle slows down to a very low speed, typically below 10 km/h, to prevent the engine from stalling by disengaging the power transmission between the engine and the gearbox. 2. When decelerating during normal driving, if lifting the accelerator pedal does not achieve the desired speed reduction, you should use the brake to adjust the speed. In this case, the clutch usually does not need to be depressed, but the left foot should remain on the clutch pedal, ready to depress it if necessary. If the speed drops to a level incompatible with the current gear, depress the clutch and shift gears. 3. If the vehicle needs to come to a complete stop while moving, first lift the accelerator pedal and apply the brake. At the moment the vehicle is about to stop, depress the clutch, shift to neutral, and engage the handbrake.

15

4

Share

What Causes the Steering Wheel to Make Noise When Turned to the Full Lock?

Analysis of the reasons for the squeaking noise when the steering wheel is turned to the full lock is as follows: 1. If the noise occurs in the morning or when the car is not warmed up, accompanied by slight shaking of the car, it is a normal phenomenon. The reason is the Ackermann angle design. The Ackermann angle is the angle difference between the outer and inner wheels when the car is turning. Because the turning radius of the inner and outer wheels is different, the inner wheel always needs to turn more than the outer wheel to ensure smooth turning of the car body. 2. Issues with the power steering fluid. Power steering fluid is essentially hydraulic oil. The power for the steering system comes from the hydraulic oil. If the hydraulic oil becomes dirty or deteriorates, the oil film formed cannot meet the normal working strength, and the lubrication performance of the deteriorated hydraulic oil decreases, leading to increased friction between metal parts, reducing the service life of the parts, which may cause noise when the steering wheel is turned. 3. Some car models use hydraulic power steering. When the steering wheel is turned to the full lock, the hydraulic power steering pump is under high load conditions, which can cause noise, and this is a normal phenomenon.

2

1

Share

Differences Between Iridium-Platinum and Double Iridium Spark Plugs

Here are the specific differences between iridium-platinum and double iridium spark plugs: 1. Electrode Material: Both iridium and platinum are rare metals with higher melting points, allowing them to maintain stable performance under high temperatures generated by discharge and combustion. 2. Melting Point: Iridium has a higher melting point than platinum, enabling iridium spark plugs to maintain more stable ignition under high temperatures. Additionally, due to the higher melting point of iridium spark plugs, the center electrode can be made thinner, requiring lower ignition voltage and improving discharge performance. Iridium-platinum has a lower melting point than double iridium, but under normal conditions, platinum spark plugs can still deliver excellent performance, with iridium-platinum spark plugs focusing on stable performance. 3. Hardness: Iridium is significantly harder than platinum, giving iridium-platinum spark plugs higher durability and a longer lifespan compared to platinum spark plugs. Double iridium spark plugs provide faster ignition speed than iridium-platinum spark plugs, and engines using iridium spark plugs exhibit better acceleration performance.

18

1

Share

Is it necessary to service a new car every 3 months?

It is essential to service a new car every 3 months. The six major taboos during the break-in period of a new car are as follows: 1. Avoid emergency braking: Emergency braking not only impacts the braking system during the break-in period but also increases the load on the chassis and engine. It is best to avoid emergency braking within the first 300 kilometers of driving. 2. Avoid overloading: Running a new car at full capacity during the break-in period can damage the components. Therefore, within the first 1,000 kilometers, the load should generally not exceed 75%-80% of the rated capacity. 3. Avoid long-distance trips: Driving long distances during the break-in period increases the continuous working time of the engine, which can easily lead to component wear. 4. Avoid high-speed driving: There are speed limits for new cars during the break-in period. Generally, the speed should be kept below 100 km/h. When the throttle is fully open, the speed should not exceed 80% of the maximum speed. Additionally, monitor the engine tachometer and speedometer to ensure the engine operates at medium speed. Typically, the engine speed during the break-in period should be between 2,000-4,000 rpm. 5. Avoid changing the oil too early: The initial oil in a new car is specifically designed for the break-in period, featuring low viscosity, excellent heat dissipation, cleaning, and anti-oxidation properties. Some manufacturers even add grinding agents to facilitate the break-in process. Therefore, the oil should only be changed according to the manufacturer's recommended schedule, not prematurely. 6. Avoid starting without warming up: A new car must be warmed up before starting. Warming up essentially gives the engine sufficient time for lubrication, especially for turbocharged models, which require at least one minute of lubrication time before starting.

6

5

Share

What is the seat height of the Suzuki GSX250R?

The seat height of the Suzuki GSX250R is 78cm. Below is more related information: Introduction to the Haojue Suzuki GSX250R: The Haojue Suzuki GSX250R is a quality-renowned sports-style motorcycle. In terms of performance, it is quite suitable as a short-distance commuting tool, and its eye-catching and stylish appearance adds to its appeal. The overall design of this bike is not only compact but also elegant. While it may lack a bit of aggressiveness, the unique Suzuki decals give it a distinctive flavor, making its appearance impeccable and arguably the best-looking in its class. Power Introduction: In terms of power, the GSX250R is equipped with a twin-cylinder, water-cooled, fuel-injected engine. The technological level of this engine is not considered very advanced among similar models, as it only features a conventional single overhead camshaft two-valve design. However, this design has its advantages—it is not overly aggressive in power extraction, resulting in higher engine durability.

17

2

Share

Does the 10th-generation Civic have a rear anti-collision beam?

What is the replacement interval for spark plugs?

Should You Depress the Clutch When Turning?

What Causes the Steering Wheel to Make Noise When Turned to the Full Lock?

Differences Between Iridium-Platinum and Double Iridium Spark Plugs

Is it necessary to service a new car every 3 months?

What is the seat height of the Suzuki GSX250R?

How to turn off the car SOS?

What is the steering wheel technique for driving in an S-curve?

Who Invented the Internal Combustion Engine?

How Often Should the Air Filter Be Replaced?