Does Rapid Acceleration Damage the Car?

Do Plug-in Hybrid Vehicles Need to Be Charged?

Plug-in hybrid vehicles do require charging. Here are the specific details: 1. In simple terms, a plug-in hybrid electric vehicle (PHEV) is a type of vehicle that falls between a pure electric vehicle and a traditional fuel-powered vehicle. It is equipped with both the internal combustion engine, transmission, drivetrain, fuel system, and fuel tank of a conventional fuel-powered car, as well as the battery, electric motor, and control circuitry of an electric vehicle. Moreover, its battery capacity is sufficient to support driving in pure electric mode for a certain distance and includes a charging port. 2. In principle, plug-in hybrid vehicles can operate without being charged because when the battery is depleted, the engine can drive a generator to produce electricity. This electricity is then directly delivered to the electric motor via the motor controller, which in turn drives the vehicle. The power battery can also be charged externally. If the battery pack becomes ineffective or unusable, the engine alone can drive the electric motor to power the vehicle. Additionally, the power battery can be charged while the vehicle is parked. 3. However, due to the presence of the battery, plug-in hybrid vehicles are significantly heavier than traditional gasoline-powered vehicles. When the battery is depleted, the fuel consumption over the same distance is higher compared to conventional gasoline cars. Therefore, it is recommended to charge the vehicle promptly to achieve fuel-saving purposes. 4. Under normal circumstances, a typical plug-in hybrid vehicle needs to be charged every 2 to 3 days, with the charging schedule arranged according to individual usage scenarios.

3

5

Share

What is the reason for the noise at idle speed that disappears when the clutch is pressed?

The causes of such abnormal noise are as follows: 1. It is basically a problem with the clutch. Most abnormal noises are caused by issues with the clutch release bearing. You can go to a professional repair shop to check the release bearing. Since the release bearing may be loose or detached, when the engine vibrates, the loose release bearing vibrates along with it, producing a rattling sound. When the clutch is pressed, the clutch presses it tight again, so there is no noise. When the clutch is released, the release bearing becomes loose again, and this cycle repeats. 2. Another possibility is that the noise is the sound of the transmission gears. This requires disassembly and inspection to determine the source of the noise. Generally, this kind of noise occurs in new cars and is a sound produced during machine processing, which is difficult to address.

14

1

Share

What to Do with Leftover Engine Oil After Maintenance?

Here are the methods for handling leftover engine oil after maintenance: 1. Seal Immediately: After completing maintenance at a 4S shop or repair shop, immediately tighten the cap of the oil bottle or container. Since the tin foil seal has been broken, the remaining cap gasket provides limited isolation. At this point, you can cover the mouth of the bottle or container with a clean plastic film. To avoid tearing, it's best to fold the film several times before covering, then tighten the cap. This method offers better sealing. If possible, you can also apply wax to the cap for additional sealing. 2. Store in a Dry and Dark Place: After sealing the oil bottle, store it in a dry and cool place, ensuring it is not exposed to sunlight to prevent oxidation of the oil inside. 3. Avoid Pouring It All In: When using the stored oil for the next maintenance, do not pour all of it into the engine. Retain a small portion. Generally, after long-term storage, there may be trace amounts of moisture at the bottom of the oil bottle or container. Adding this to the engine could affect its performance or even cause adverse effects.

20

2

Share

Do car batteries need regular charging?

Car batteries require regular charging. It is recommended to charge the battery every two weeks when the vehicle is idle. If the battery is in good condition, there is no need to remove it for charging; simply starting the car will allow the alternator to charge the battery. However, if the car battery is severely depleted, it should be removed and charged with an external charger. Below are specific details about battery charging: 1. Start the car to charge using the alternator; it should be fully charged every half month. 2. Use an external charger; it should be fully charged once a month. 3. For car battery charging, it should be fully charged every three months. The lifespan of a car battery is relatively long. Generally, if the battery is located in the engine compartment, its lifespan is approximately 2-4 years.

1

2

Share

Why does the engine sound become louder when stepping on the accelerator?

When stepping on the accelerator, the engine sound becomes louder for several reasons: 1. The pipe connecting the air intake grille to the air filter is loose, and fixing it with tape will solve the issue. 2. The external belt is squealing, requiring repair at a 4S shop. 3. There is an issue with the internal mechanical parts of the engine. If under warranty, immediately report to a 4S shop for inspection and repair. Below are common engine problems: 1. Abnormal engine vibration: The most common cause is dirty throttle leading to idle vibration. Other causes include faulty spark plugs, damaged ignition coils, or mechanical engine failures. 2. Severe engine carbon buildup: The main reasons for severe carbon buildup are the use of low-quality engine oil and fuel. Engines with severe carbon buildup often exhibit symptoms like idle vibration, weak acceleration, high fuel consumption, and difficulty starting when cold. 3. Engine overheating: The normal operating temperature of an engine is between 80~90°C. Temperatures exceeding this range are defined as engine overheating. Excessive engine temperature can even lead to severe mechanical failures like cylinder scuffing or bearing damage.

15

1

Share

What to Do When the Car Paint Surface Loses Shine After Sanding?

When the car paint surface loses shine after sanding, you will need automotive-specific gloss sealant, coating sponge, and towels. Below are the detailed steps for the operation: 1. First, wipe the car body clean with a damp towel to ensure there are no dust or other particles on the surface. 2. Then, press the sponge onto the gloss sealant, shake the gloss sealant, and pour it onto the sponge. 3. Next, use the sponge to sand the car body, ensuring even friction and rubbing slowly. 4. Finally, use a clean towel to wipe off any excess liquid and clean the car body thoroughly. 5. In the end, you will see the car body shining brightly, with a noticeable effect.

8

4

Share

Does Rapid Acceleration Damage the Car?

Do Plug-in Hybrid Vehicles Need to Be Charged?

What is the reason for the noise at idle speed that disappears when the clutch is pressed?

What to Do with Leftover Engine Oil After Maintenance?

Do car batteries need regular charging?

Why does the engine sound become louder when stepping on the accelerator?

What to Do When the Car Paint Surface Loses Shine After Sanding?

What is the Function of Engine Start-Stop?

Why Does the Car Sound Get Louder?

What does 'hold' mean in a car?

Where is the windshield washer nozzle located?