Does Not Disconnecting the Wires Affect Car Charging?

1 Answers
JamesMarie
07/29/25 6:06pm
Not disconnecting the wires during car charging does not have any negative effects. In fact, disconnecting them can lead to the loss of some data in the ECU. After the charging connection is broken, restarting the car may result in increased fuel consumption because certain data stored in the ECU will be lost. The car's ECU has a strong learning capability—it can learn the driver's habits and save this data. If the battery's positive and negative terminals are disconnected, the ECU loses the data related to the driver's habits, leading to noticeably higher fuel consumption when driving again. This is why many drivers experience increased fuel consumption after replacing the battery, as some ECU data is lost. It is best to charge the car battery without disconnecting it. Simply connect the positive terminal of the charger to the battery's positive terminal and the negative terminal of the charger to the battery's negative terminal. Precautions for car battery charging: In cold weather, check if the electrolyte is frozen before charging—never charge a frozen battery as it may cause an explosion. Also, check the electrolyte level before charging; do not charge if the electrolyte is insufficient. During charging, measure the electrolyte density and voltage every hour and monitor the temperature.
Was this review help?
2
3
Share
More Forum Discussions

Is the Bentley Continental a Sedan or a Sports Car?

Bentley Continental is a sports car launched by Bentley Motors Limited in the UK. Taking the Bentley Continental GT as an example: its exterior dimensions are 4850mm in length, 1954mm in width, and 1405mm in height, with a wheelbase of 2851mm. The drive system options include front-wheel drive and full-time four-wheel drive. The Bentley Continental GT is equipped with a V6 6.0T and a 4.0T W12 twin-turbocharged engine. It features a double-wishbone independent front suspension, a multi-link independent rear suspension, electronic parking, two high-definition displays, a three-sided rotating display, a 12.3-inch touchscreen navigation system, and mirrors with turn signals and cameras.
10
2
Share

What is the middle pedal in a car called?

The middle pedal in a car is the brake pedal, which is used to slow down or stop the vehicle. From left to right, the pedals in a car are the clutch pedal, brake pedal, and accelerator pedal. The brake pedal is the largest among the three, and its sensitivity and travel distance vary depending on the car model. Here are some details about car pedals: 1. Normally, only manual transmission cars have three pedals. Automatic transmission cars, controlled by the onboard computer for gear shifting, do not require a clutch pedal and only have the accelerator and brake pedals. 2. While driving, the left foot controls the clutch, and the right foot controls the brake and accelerator. When not in use, the left foot should not rest on the pedal; there is a designated area in the driver's compartment for the left foot. Keeping the left foot on the pedal during long drives can lead to unintentional pressing, which can be very dangerous while driving.
3
3
Share

What are the differences between Toyota's third-generation and fourth-generation hybrid systems?

Higher thermal efficiency, transmission system, suspension, etc. Here are the specific details: 1. Thermal efficiency: The third generation has a compression ratio of 12.5, while the fourth generation has 14, making it more fuel-efficient and more powerful. 2. Transmission system: The fourth generation adds gears at low speeds, providing more direct transmission and a quicker start feel. 3. Suspension: The current model uses the old RAV4 chassis, while the next generation is expected to use TNGA. You can test drive the UX; its chassis performance and noise control are significantly better than the current NX. 4. Four-axis structure: Consists of a torque limiter, one-way clutch, input shaft, planetary gear mechanism, motor, reduction device, and differential device. Among these, the planetary gear mechanism acts as a power split device, determining whether the engine power is supplied to motor MG1 or used as vehicle driving force. Motor MG2 and its reduction device adopt a parallel-axis layout.
19
5
Share

Can I Change the Car Air Filter Myself?

Car air filters can be replaced by yourself. The main components of an air filter are the filter element and the housing, where the filter element is the primary filtering part responsible for gas filtration, while the housing provides the necessary external protection for the filter element. Below are the steps to replace the air filter: 1. First, open the glove box cover. Locate the fixing buckle on the right side of the glove box and pull it outward firmly. 2. Remove the fixing buckle of the glove box cover to detach it. 3. Squeeze both sides of the glove box towards the middle with both hands, and the glove box can then be taken off. 4. After removing the glove box, you will see the air filter cover. Press firmly on the fixing buckles on both sides of the cover, and the cover can then be removed.
20
2
Share

How long can a car key still be used after the battery replacement reminder?

Car key batteries typically last for three years after replacement. Relevant information is as follows: 1. Introduction: The lifespan of a car key battery is generally 2-3 years. However, due to differences in usage habits, some drivers' car keys may run out of power in just one year, while others can last for 5 or even 10 years. This is largely related to our usage habits. On average, the lifespan is slightly over 2 years. With poor usage habits, the battery may die within a year. 2. Function: When the car key battery needs replacement, there's no need to visit the 4S store. In fact, the function settings and execution of the car key are determined by the motherboard inside the key, while the battery provides the power needed for these functions to operate.
9
2
Share

Are Engine Oil and Transmission Fluid the Same?

Engine oil and transmission fluid are not the same. Engine oil is the lubricant for the engine system, possessing properties such as oxidation resistance, anti-wear, and anti-corrosion. Transmission fluid, on the other hand, is primarily used to keep the gear system clean, ensuring the transmission operates properly and extending the lifespan of the transmission components. Below is a detailed explanation of their respective functions: 1. The main function of transmission fluid is to keep the vehicle's gear system clean. It lubricates and cools the gear system. During driving, the gears operate at high speeds, generating heat through friction. Transmission fluid is then needed to lubricate and reduce temperature, ensuring the vehicle operates normally. 2. The main function of engine oil is to lubricate the engine system, providing lubrication, cooling, sealing to prevent leaks, rust and corrosion prevention, as well as shock absorption. It can be said that the condition of the engine oil directly affects the performance and lifespan of the engine.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.