Does leaving the car door open during rain causing water ingress affect the vehicle?

1 Answers
DelJosie
07/29/25 8:57am
Leaving the car door open during rain causing water ingress does affect the vehicle. It can lead to interior dampness, making the upholstery prone to mold growth and damaging leather seats. If a large amount of water enters, excessive dampness inside the car may cause electrical short circuits. If water enters the engine, it may render the engine inoperable. Below are some additional details: Precautions: When driving in the rain, it is best to completely seal the doors, windows, and sunroof to prevent rainwater from entering and causing dampness inside the vehicle. If you forget to close the sunroof during rain and water enters, the first step is to dry the interior thoroughly. Try to wipe away any accumulated water and ventilate the car. You may also need to replace seat and floor mats, dry them in the sun when possible, and consider placing a dehumidifier box inside the car to absorb moisture.
Was this review help?
14
5
Share
More Forum Discussions

Is the Clicking Sound in the Cruze Engine Normal?

It is normal for the Cruze engine to produce a clicking sound; this is the sound of the carbon canister solenoid valve operating. The function of the carbon canister solenoid valve is to open the solenoid valve between the carbon canister and the intake manifold once the engine starts, allowing the gasoline vapors adsorbed in the carbon canister, along with air, to be drawn into the cylinder for combustion. This component produces a crisp clicking sound during operation. Taking the Cruze 2020 320T Manual Xinkuai Edition as an example, its body dimensions are 4614mm in length, 1798mm in width, and 1485mm in height, with a wheelbase of 2640mm. The body structure is a 4-door, 5-seat sedan, and the drivetrain is front-engine, front-wheel drive.
5
1
Share

How to release the handbrake on a Citroën?

Release the handbrake with five fingers. Place four fingers on the gear lever, lift it slightly upwards, press the unlock button with your thumb, and push it all the way down. In the original clutch position, it is usually engaged by stepping on it once and released by stepping on it again.
2
0
Share

How to reset the maintenance light on Volkswagen Jetta VS5?

The method to reset the maintenance light on Volkswagen Jetta VS5 is: 1. Turn off the car and hold the right button on the dashboard with your left hand without releasing it; 2. While keeping the right button pressed with your left hand, turn the key with your right hand to illuminate the dashboard. At this point, a small wrench indicator light will appear on the dashboard and remain steady without flashing; 3. Release the left hand and press the left button on the dashboard, then the wrench symbol will disappear. Taking the 2021 280TSI Jetta VS5 Manual Base model as an example, its body dimensions are 4419mm in length, 1841mm in width, and 1616mm in height, with a wheelbase of 2630mm, and the body structure is a 5-door, 5-seat SUV.
11
2
Share

How to set the time on the small screen of the 2011 Highlander?

The method to set the time on the small screen of the 2011 Highlander is: 1. There is a disp button on the right side of the steering wheel. First, press this button briefly until the clock (clock) is displayed, then press and hold the button, and the hour digits will start flashing; 2. Continue holding the disp button until the desired hour is reached, then release. After about 5 seconds, the minute digits will start flashing. Press and hold the button again until the desired minute is reached. Taking the 2011 Highlander 2.7L 2WD 5-seat Elite Edition as an example, its body dimensions are 4785mm in length, 1910mm in width, and 1730mm in height, with a wheelbase of 2790mm. The body structure is a 5-door, 5-seat SUV.
5
1
Share

How to parallel park with an A2?

Prepare to reverse and turn on the right turn signal. When reversing, look from the middle of the car body and turn the steering wheel one and a half turns to the right. Look at the left rearview mirror and observe the right corner at the back of the garage. At this point, straighten the steering wheel and continue reversing. Watch the left rearview mirror. When you see the left rear wheel of the car touching the left line of the garage, turn the steering wheel all the way to the left. Once the car is aligned within the garage, straighten the wheels to park. Turn on the left turn signal. Since the steering wheel was turned all the way to the left in the previous step, there’s no need to straighten it. Shift into first gear, move forward past the left side of the garage, and turn the steering wheel one and a half turns to the right. Once the car is straightened, drive forward and turn off the turn signal.
12
3
Share

What is the process flow of sheet metal painting?

Filling the sand marks and micro-pores on the bottom layer of the workpiece to enhance the adhesion of the underlying paint, and also serving as a defect indicator. A very important coating part, preparing a complete and smooth working surface for the topcoat, completing the final step of all primer work. The topcoat is divided into single-layer paint and multi-layer paint, serving as the color-determining layer and decorative protective layer. Single-layer paint is commonly referred to as solid color paint, also known as standard paint, and can be completed in one layer.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.