Does it matter if there is a little more engine oil?

2 Answers
JackLynn
07/25/25 6:49am
Exceeding the upper limit of the engine oil dipstick by a small amount can have adverse effects, leading to engine oil burning, primarily manifested as blue smoke from the exhaust pipe. The details are as follows: 1. Symptoms of oil burning: If the engine shakes at idle, or if the engine oil is significantly depleted within a routine maintenance (oil change) cycle (without any leakage), then the vehicle is experiencing oil burning. 2. Causes of oil burning: (1) Incorrect installation or misalignment of piston rings, though this is rare and has a low probability of occurrence. (2) Overfilling of engine oil, exceeding the upper limit mark. (3) Dirty throttle body.
Was this review help?
20
3
Share
LaCooper
08/10/25 6:18pm
Having too much engine oil does make a difference. I experienced this right after an oil change - the engine sounded off when I hit the road, and the car felt sluggish. Upon checking, I found the oil was slightly overfilled. Excess oil causes the crankshaft to churn it, creating air bubbles that compromise lubrication. Long-term, this accelerates engine wear and may even lead to oil leaks. I remember the mechanic using the dipstick to measure, showing the level above the Max mark. He said it's a common mistake. After draining some oil, everything returned to normal. My advice: always check with the dipstick post-oil change to ensure levels stay between Min and Max, preventing impacts on driving safety and fuel efficiency. Paying attention to this during regular maintenance extends your car's lifespan and saves on repair costs - never overlook it.
Was this review help?
5
5
Share
Expand All
More Forum Discussions

What engine is used in the GAC Trumpchi PHEV?

The engine of the GAC Trumpchi PHEV is a hybrid power engine independently developed by GAC Group, belonging to a domestically produced engine. The engine model of the GAC Trumpchi PHEV is 4A15K2, with a maximum horsepower of 97, a maximum power of 71kW, and a maximum torque of 120 Nm. For daily maintenance of the GAC Trumpchi PHEV engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, SD-SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB-CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid faults, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
11
4
Share

What is the suitable tire pressure for the Arrizo 5?

The standard tire pressure range for the Arrizo 5 is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and reduced by 0.1 bar in summer. This data is based on the international GBT2978-2008 standard requirements. The Arrizo 5 is only equipped with a tire pressure monitoring system in the Premium version. The tire pressure value is displayed on the central LCD screen of the instrument panel. To display the tire pressure, simply press the combination instrument LCD adjustment button on the left side of the steering wheel to switch to the tire pressure monitoring system interface. Other versions of the model can have a tire pressure monitoring system installed, and the display interface can be enabled by reprogramming the instrument computer. Generally speaking, a tire pressure above 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; causing steering wheel vibration and deviation, reducing driving comfort; accelerating wear on the central tread pattern, shortening tire lifespan; increased body vibration, indirectly affecting the lifespan of other components; excessive stretching of tire cords, reducing tire elasticity and increasing the load on the vehicle during driving. Hazards of insufficient tire pressure: Increased friction coefficient with the road surface, leading to higher fuel consumption; causing heavy steering and deviation, which are unfavorable for driving safety; increased movement of tire parts, leading to abnormal overheating due to excessive rolling; reduced functionality of cords and rubber, causing delamination or cord breakage and excessive friction with the rim, damaging the tire bead area and causing abnormal wear; multiplied increase in friction between the tire and the ground, sharply raising tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to tire blowouts. If the tire pressure monitoring indicator light comes on (a yellow symbol, an irregular circle with no seal on top and four small spikes at the bottom, with an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Usually, an alarm is triggered when the pressure is below 1.8 bar or above 3.0 bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset in time, the tire pressure monitoring system will still record the previous data, causing the indicator light to come on. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is directly installed inside the tire and connected to the tire inflation port. If the sensor is damaged due to impact during driving, the tire pressure fault light will also come on. For sensor damage issues, the only solution is to replace it with a new component.
17
1
Share

What are the most damaging behaviors for automatic transmission vehicles?

Automatic transmission vehicles are most damaged by the following behaviors: 1. Do not tow the vehicle arbitrarily when it has a malfunction: When a car breaks down and needs towing, the automatic transmission cannot be directly shifted into neutral like a manual transmission, as this can damage the transmission. After a malfunction occurs, the transmission oil pump cannot operate, and the components lack lubrication and cooling. When the car is towed, the transmission is still in operation, which can cause damage. Before towing, it is important to determine whether the car is front-wheel drive, rear-wheel drive, or four-wheel drive. In any case, avoid towing the drive wheels of an automatic transmission vehicle. 2. Do not coast in N gear while driving: In the past, many people might have coasted in neutral to save fuel with manual transmission cars, but this is not advisable for safety reasons. Similarly, automatic transmission vehicles should not coast in N gear while driving because the transmission requires gear oil for lubrication. If the transmission is in neutral, the oil cannot properly lubricate the transmission, which may cause certain components to overheat or the gears to be damaged. In severe cases, the transmission may be ruined. 3. Do not shift into P gear before the vehicle has come to a complete stop: When parking, always engage the handbrake first so that the force is initially borne by the handbrake. Shifting directly into P gear puts all the force on the transmission, and if the car is hit by an external force while parked, it may cause internal damage to the transmission. 4. Shifting into R gear before the car has fully stopped: Automatic transmissions are much more delicate than manual transmissions. Engaging R gear while the car is still moving from D gear can cause a strong impact on the transmission, leading to premature failure. 5. Incorrect use of P and D gears: When waiting at a traffic light for about 30 seconds, you can stay in D gear with the foot brake engaged. For longer waits, shift into N gear with the brake engaged, but do not use P gear. If the car is hit hard while in P gear, the transmission can suffer significant damage. As automatic transmission vehicles gradually replace manual ones for their convenience, it is important to pay extra attention to driving habits and maintain good practices.
1
4
Share

Actual Fuel Consumption of Hyundai ix25?

The actual fuel consumption of the Hyundai ix25 ranges from 5.3L to 8.2L. More details about the Hyundai ix25 are as follows: 1. The Hyundai ix25 is positioned as a compact SUV, offering both two-wheel drive and on-demand four-wheel drive models. Its body dimensions are 4270mm/1780mm/1630mm with a wheelbase of 2590mm. 2. The Hyundai ix25 is available in four models: GS-6MT Manual Fashion, GLS-CVT Smart, DLX-CVT Premium, and TOP-CVT Flagship.
11
0
Share

At how many kilometers should a car undergo a major maintenance service?

Car should undergo a major maintenance service at around 20,000 to 30,000 kilometers. The items included in a major maintenance service are: 1. Replace engine oil and oil filter; 2. Replace air filter and fuel filter; 3. Check the performance of lighting lamps, warning lights, turn signals, and car horn; 4. Check the performance of windshield wipers and cleaning devices; 5. Check the travel of the clutch pedal; 6. Check the rear wheel hub bearing clearance and grease lubrication; 7. Check the condition of spark plugs; 8. Check whether the seat belts are intact; 9. Check the exhaust system for any damage; 10. Check the tie rod end joint clearance, fixation, and dust cover sealing.
10
1
Share

Why does the reverse radar button light keep flashing?

It flashes when there is a malfunction, likely due to an unplugged connector or a damaged reverse radar that hasn't been replaced. Here are some related points about reversing: 1. Precautions: Whether you're a beginner or an experienced driver, this is crucial. Not only should you avoid pressing the accelerator while reversing, but you should also avoid half-pressing the brake. Beginners should drive at a speed slower than idle when reversing. This allows more time to observe the surroundings. 2. Basic principles: When parking in a parking lot, first, visually assess the width of the parking space, check for any obstacles behind, whether there are vehicles parked on either side, and if the length suits your vehicle. If visibility is poor at night, step out to check the exact position before reversing.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.