Does idling with AC on in summer damage the car?

1 Answers
MacIsabelle
07/29/25 7:57pm
It does not cause any special damage to the car, only normal wear and tear. Below are the impacts of idling with AC on: 1. Increased emission of harmful gases: Idling with AC on emits more harmful exhaust gases compared to driving with AC on, because idling is the most unfavorable operating condition for the engine, where gasoline combustion is relatively incomplete, resulting in higher emissions of carbon monoxide, hydrocarbons, nitrogen oxides, and other harmful gases. 2. Significant harm to human health: Idling with AC on can cause harm or even death to occupants if not careful. There are mainly two types of harm: one is hypoxia and suffocation, and the other is carbon monoxide poisoning. When idling with AC on, it must be done in an open area. Never stay in the car for a long time in a confined small space, as the carbon monoxide emitted by the car can enter the vehicle, easily leading to carbon monoxide poisoning.
Was this review help?
18
4
Share
More Forum Discussions

How to solve the problem that the oil-gas conversion switch does not light up?

Open the driver's door of the car. Step on the brake pedal to prepare to start the engine; press the one-button start key of the car. All the dashboard lights come on, and the engine starts. Press the top of the toggle lever located on the right side of the steering wheel, hold it down for more than 5 seconds without releasing, and the matching will be completed.
6
1
Share

How to Turn on the Cold Air in Haima Automobile Air Conditioning?

Enter the vehicle interior to locate the air conditioning adjustment area. The left knob in the control area is the air conditioning temperature adjustment knob, turning clockwise increases the temperature. The A/C button is the air conditioning cooling button; press this button when cold air is needed. The middle knob is the air vent direction adjustment knob. The right knob adjusts the air volume, turning clockwise increases the air volume. The button at the bottom left adjusts between the air conditioning's internal and external circulation modes. The bottom right is the switch for the rearview mirror heating function after rain.
7
1
Share

How to make slight adjustments to the steering wheel when driving straight?

Hands should not grip the steering wheel too tightly; instead, place them on the steering wheel lightly to allow for timely adjustments. When making steering adjustments, avoid applying excessive force, meaning you shouldn't turn the wheel too much to the left or right. Driving in a serpentine manner on the road is extremely dangerous.
15
0
Share

How to adjust the exhaust brake valve of Weichai WP12?

Rotate to position the first cylinder piston at the top dead center of combustion. Adjust the intake valves of cylinders 1, 2, and 4. Loosen the intake valve lock nut, adjust the bolt, and insert a feeler gauge. Turn the adjustment screw and tighten the lock nut with a torque wrench. Loosen the EVB bracket lock nut and rotate the EVB bracket adjustment screw to compress the small piston until it is fully depressed. Finally, repeat the above steps to adjust the intake valve clearance of cylinders 3, 5, and 6, and the exhaust valve clearance of cylinders 2, 4, and 6.
19
2
Share

How to Deal with Engine Oil Stains on White Shoes?

Use hand cream or essential balm to wipe. Lightly dab a tissue with hand cream or essential balm and gently rub the stain, which should come off quickly. Be careful not to drip it directly onto the shoes. Wipe the surface of the shoes with a damp cloth, then use an eraser to gently remove visible stains. This will restore the shine to the shoes and make the stains disappear. Apply a thin layer of toothpaste on the shoes and wipe clean with a cloth. The stains will gradually fade, and after a few thorough wipes, they will be completely gone.
18
1
Share

How to Repair Scratches on Carbon Fiber Surface?

Sand the damaged area outward from both sides using sandpaper, ensuring the sanded area is slightly longer than the damaged section, and appropriately thin the damaged area. Cut the carbon fiber cloth to size and fully saturate it with epoxy resin. Then, evenly apply a layer of resin to the damaged surface and wrap the carbon fiber cloth around the affected area. Wrap with electrical tape and apply pressure to squeeze out excess resin. After the resin has cured, remove the electrical tape and sand the surface smooth. Finally, proceed with painting: first apply the base coat, then restore the lettering or patterns, followed by clear coat application, sanding, and polishing.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.