Does exceeding the oil level limit have any impact?

2 Answers
MelanieDella
07/25/25 4:47am
Exceeding the oil level limit does have an impact. If too much oil is added, the resulting hazards include reduced power, increased carbon deposits, worsened exhaust emissions, and engine oil leaks. When the engine is running, the crankshaft and connecting rods inside rotate rapidly. Since the crankshaft stirs within the oil, higher oil pressure makes it more difficult for the crankshaft to rotate. Excessive oil can hinder the crankshaft's movement, leading to decreased engine power output. There is a yellow pull ring in the engine compartment—this is the oil dipstick. When pulled out, you can see two marked lines or sometimes two holes at the lower end of the dipstick, indicating the upper and lower limits of the oil level. The vehicle's oil level must be maintained between these two marks to be considered normal.
Was this review help?
13
1
Share
VonLucas
08/10/25 5:30pm
Hey, this is a common issue I've seen in decades of car repairs. A slight overfill might not be a big deal, but too much can cause serious trouble. The engine generates extra pressure, which can aerate the oil, reducing lubrication efficiency and accelerating wear on cylinder components over time. Worse yet, oil seals may leak, leaving the engine bay greasy, and you might even notice blue smoke from burning oil. I once handled a case where a customer poured in a full container of oil, rendering the car undrivable—turned out the excess caused a seal to burst. Always check oil levels carefully and never exceed the MAX line. If you accidentally overfill, it's best to drain some out or visit a professional shop. Bottom line: treat oil levels seriously. Keeping it at the midpoint ensures engine protection while saving you headaches and money.
Was this review help?
3
3
Share
Expand All
More Forum Discussions

Can the vehicle body touch the line in the S-curve of Subject 2?

In the S-curve of Subject 2, the vehicle body can touch the line as long as the wheels do not cross it. Below is some relevant information about the S-curve in Subject 2: Practical method for the S-curve in Subject 2: Before entering the left curve, the vehicle should drive close to the right side, keeping the right side of the car pressed against the right line. When preparing to switch to the right curve, turn the steering wheel to the right, using the left front corner of the car to press against the left line until the vehicle safely exits the curve, then turn the steering wheel back to the right. New regulations for the S-curve in Subject 2: If the wheels run over the edge line of the road, it results in failure; stopping midway results in failure; driving without shifting to second gear or above results in a deduction of 5 points.
6
1
Share

What is the fuel consumption of the Toyota 86?

Toyota 86 fuel consumption? Actual fuel consumption varies depending on driving habits, typically ranging between 9 to 11 liters. The Toyota 86 is a sporty rear-wheel-drive vehicle, and its fuel consumption largely depends on the owner's driving style. The Toyota 86 is a two-door coupe equipped with a 2.0-liter horizontally opposed four-cylinder engine, codenamed FA20. This naturally aspirated engine delivers a maximum power of 147 kW and a maximum torque of 205 Nm, with peak power achieved at 7,000 rpm and peak torque between 6,400 to 6,600 rpm. The engine features hybrid injection technology and utilizes an aluminum alloy cylinder head and block.
18
3
Share

How to Adjust the Brightness of the Car Dashboard?

In the settings of the central control screen, there is an option to adjust the brightness of the dashboard. Below is some relevant information about the car dashboard: Definition: The car dashboard is a device that reflects the working conditions of various vehicle systems. Common indicators include the fuel indicator, washer fluid indicator, electronic throttle indicator, front and rear fog light indicators, and warning lights. Speedometer: The speedometer actually consists of two gauges. One is the speedometer, and the other is the odometer. Tachometer: The tachometer is generally located within the dashboard and is placed symmetrically with the speedometer.
11
5
Share

Do All Turbocharged Cars Burn Engine Oil?

Regarding the above vehicle inquiry, models equipped with turbochargers generally do not experience engine oil burning. Oil burning is usually caused by improper turbo maintenance. Therefore, for vehicles with turbochargers, the following usage recommendations should be noted: It is recommended to use synthetic lubricating oil and regularly replace and clean the air filter. Additionally, after high-speed operation, do not shut off the engine immediately. Sudden shutdown can interrupt oil lubrication, and the internal heat of the turbocharger cannot be dissipated by the oil, which may cause the turbocharger's rotating shaft and bushing to seize.
17
5
Share

What is a car chassis composed of?

An automobile chassis is a system composed of four main parts: the drivetrain, the running gear, the steering system, and the braking system: 1. The drivetrain structure of a car mainly refers to the power transmission device between the engine and the driving wheels, consisting of components such as the clutch, universal joint, and drive axle. The primary function of the drivetrain is to ensure the necessary traction, speed, and coordinated changes between speeds under various driving conditions. In other words, it ensures the car can reverse and that the left and right driving wheels can adapt to differential requirements. 2. The running gear of a car is composed of components such as the frame, wheels, and suspension. Generally, what we refer to as vehicle handling is determined by the running gear. Its main function is to convert the torque transmitted by the drivetrain into the driving torque of the car through the adhesion between the wheels and the road surface. Additionally, it supports the total mass of the car, mitigates impacts, reduces vibrations, and ensures driving stability. 3. The steering system of a car mainly refers to a series of devices used to change or maintain the direction of travel or reverse. For example, the steering control mechanism, steering gear, and steering linkage are all part of the steering system. Its primary function is to control the vehicle's direction according to the driver's intention, which is crucial for driving safety. 4. The braking system refers to a series of specialized devices on a car that can generate braking force, such as brake pads and the brake pedal. Its main function is to enable a moving car to decelerate, stop, and maintain a stable speed when going downhill. The chassis is composed of four parts: the drivetrain, running gear, steering system, and braking system. The drivetrain mainly consists of the clutch, transmission, universal joint, drive shaft, and drive axle. Clutch: Its function is to smoothly engage or temporarily separate the engine's power from the transmission device, facilitating the driver's operations such as starting, stopping, and shifting gears. Transmission: Composed of the transmission case, transmission cover, first shaft, second shaft, intermediate shaft, reverse shaft, gears, bearings, and control mechanism, it is used for changing speed and torque output. The running gear consists of the frame, axle, suspension, and wheels. Its basic function is to support the entire vehicle's mass and ensure the car's movement. Leaf springs and shock absorbers: The leaf springs function to maintain an elastic connection between the frame and body with the wheels or axle. The shock absorbers function to mitigate vibrations when the car is subjected to shock impacts. Shock absorbers are used in parallel with leaf springs. The steering system consists of the steering wheel, steering gear, steering knuckle, steering knuckle arm, tie rod, and drag link, and its function is to steer the vehicle.
11
5
Share

Can 4S shops convert manual to automatic transmission?

The difference between manual transmission and automatic transmission lies in the gearbox. Manual transmission models are equipped with manual gearboxes, while automatic transmission models are equipped with automatic gearboxes. If a car is to be converted to automatic transmission at a 4S shop, the entire gearbox assembly needs to be replaced, which is not advisable. Common automatic transmissions include CVT transmissions, DCT transmissions, and AT transmissions. 1. DCT transmission: This transmission is also known as a dual-clutch transmission. The structure of this transmission differs significantly from manual transmissions, featuring two sets of clutches—one controlling odd-numbered gears and the other controlling even-numbered gears. Dual-clutch transmissions are compact, lightweight, offer fast gear shifts, and high transmission efficiency. 2. CVT transmission: This transmission is also called a continuously variable transmission. Its structure differs from other transmissions, featuring two conical pulleys and a steel belt in the CVT gearbox. 3. AT transmission: AT transmission, also known as torque converter transmission, is currently the most mature and widely used transmission. However, AT transmissions are heavy and bulky.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.