Does ETC installation require connection to the car's power supply?

1 Answers
FernandoMarie
09/03/25 5:09am
Installing ETC does not require an additional power connection, as ETC uses its own built-in power source. The ETC electronic tag consumes power, but it does not need to be charged during normal use because the battery has a solar panel on the back that allows it to charge itself. During installation, it is important to avoid the black areas on the windshield. The built-in power source of ETC typically has a lifespan of 3-5 years. ETC stands for Electronic Toll Collection, which refers to the electronic toll system. To apply for ETC, the vehicle owner must provide valid identification and the original and photocopy of the vehicle registration certificate. If the application is made by a proxy, the proxy's valid identification is also required. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection stamp. Additionally, a bank card for deducting highway toll fees is required, and the applicant must be between 18 and 60 years old, with the vehicle registered under their name. How ETC works: The onboard electronic tag installed on the vehicle's windshield communicates with the microwave antenna in the ETC lane at toll stations. Using computer networking technology, it settles transactions with the bank in the background, allowing vehicles to pass through highway or bridge toll stations without stopping to pay tolls. Benefits of installing ETC: Time-saving: Eliminates the hassle of waiting in queues. Green and eco-friendly: Promotes low-carbon travel by reducing noise and exhaust emissions, as vehicles pass through toll stations without stopping. Cost-saving: Reduces wear and tear and fuel consumption by minimizing vehicle starts and stops, and users can enjoy toll discounts. Improved efficiency: ETC lanes can theoretically increase traffic efficiency by 2-3 times, making traditional ETC more advanced, faster, and higher-tech. Compared to license plate payment, ETC technology is more mature and advantageous.
Was this review help?
6
2
Share
More Forum Discussions

Is It Necessary to Replace a Cracked Windshield?

It is necessary to replace a cracked windshield. The specific reasons are as follows: 1. The crack may expand: Cracks can continue to spread due to factors such as temperature changes, high-speed driving, and road bumps. 2. Affects the driver's vision: It may further threaten the safety of the driver and passengers in the vehicle. Relevant information about car windshields is as follows: 1. Windshield: Refers to the glass component in a car that blocks wind. 2. Function: The "cleanliness" of the car windshield can determine the clarity of the driver's vision; the quality of the car windshield is closely related to the driving safety of the driver.
16
1
Share

Why is there no response from the Mercedes-Benz 260 ignition switch?

The Mercedes-Benz 260 ignition switch does not respond because the battery is dead, the steering wheel is locked, there is insufficient fuel, or no antifreeze has been added. Reasons for a dead car battery: The car has been parked for a long time, causing the battery to lose power, the battery has reached the end of its lifespan, the engine is damaged, or there is an issue with the electrolyte. Reasons for insufficient car fuel: There is no fuel in the tank or the fuel tank switch is not open, the electric fuel pump is not working properly or has failed, or the fuel pressure regulator is not working properly. There may be blockages, leaks, water accumulation, freezing, or vapor lock in the pipeline from the fuel tank suction pipe through the fuel filter, fuel pump to the fuel distribution pipe inlet pipe joint.
2
4
Share

What Are the Dangers of a Cigarette Lighter Not Popping Out?

If it is not caused by a blown fuse, but rather by a loose or damaged retaining spring preventing the cigarette lighter from being pulled out, the lighter can still heat up normally and will remain in a heated state. This may cause the lighter's fuse to blow, and the lighter's wiring may overheat, eventually leading to charring and a short circuit. Here is some additional information: 1. Risk of fire: In severe cases, the car's cigarette lighter may catch fire, either due to the lighter's wiring or the lighter socket igniting. Since the cigarette lighter can reach high temperatures after heating, continuous heating can easily lead to a fire. 2. Cigarette lighter: The cigarette lighter is a component found in all cars, designed to provide a convenient ignition source for smokers.
15
0
Share

What to Do When the Fuel Tank Cover of an Audi A6 Won't Open?

Audi A6 fuel tank cover won't open solution: 1. Use the emergency release switch from the trunk to open the fuel tank cover. The emergency release switch is located behind the right side trim panel in the luggage compartment. Unlock the knob, pull open the trim panel, then pull the cord until you feel significant resistance to open. 2. Press the fuel tank cover. Additional information: 1. Model: The Audi A6 is a high-end luxury business car produced by Audi, available in both sedan and station wagon variants. 2. Features: Incorporating Audi's advanced global high-tech technologies, it further enriches luxurious configurations and endows it with sporty characteristics. Its features include: more luxurious, more dynamic, more mature, and more reliable.
16
0
Share

Where is the air conditioning filter located in the Zotye T700?

The air conditioning filter of the Zotye T700 is located under the front passenger seat, near the left foot position, and can be seen towards the inner side. The air conditioning filter is a type of filter installed in the car's air conditioning system, which can absorb dust particles, alleviate respiratory discomfort, reduce irritation for allergy sufferers, and protect the cooling system of the air conditioner. Below is more information about the Zotye T700: 1. Model: Taking the Zotye T700-1.8T Dual Clutch Custom Edition as an example, it is a mid-size SUV from Zotye Auto. 2. Engine: Equipped with a 1.8T 177 horsepower L4 engine, paired with a 6-speed dual-clutch transmission, the engine has a maximum power of 130kW and a maximum torque of 245Nm.
1
1
Share

How to Remove the Taillight of a Buick Excelle?

Here is the method to remove the taillight of a Buick Excelle: 1. Disconnect the negative terminal of the battery; 2. Remove the mudguard and three screws; 3. Then remove the nut securing the taillight assembly; 4. Remove one nut and two bolts; 5. Remove three cross screws; 6. There are two plastic parts under the taillight assembly that secure the rear bumper; 7. The rear bumper must be removed to take out the taillight assembly. Additional information: The Buick Excelle is an entry-level family sedan launched by SAIC-GM Buick, with the prototype being a new globally developed mid-size sedan by General Motors. In terms of body dimensions, the Excelle measures 4468mm in length, 1765mm in width, and 1469mm in height.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.