Does driving for 3 hours and 50 minutes count as fatigued driving?

1 Answers
MacIvan
07/30/25 12:36am
According to relevant Chinese laws and regulations, continuously driving a motor vehicle for 3 hours does not constitute fatigued driving. However, if continuous driving exceeds 4 hours, it is considered fatigued driving, which may lead to traffic accidents. Below is an introduction to relevant content: 1. Time definition: Continuously driving a motor vehicle for more than 4 hours without stopping for a break or stopping for less than 20 minutes. 2. Manifestations of fatigued driving: After prolonged continuous driving, drivers experience physiological and psychological dysfunction, objectively leading to a decline in driving skills. 3. Hazards of fatigued driving: Continuing to drive while fatigued can result in drowsiness, weakness in limbs, lack of concentration, reduced judgment, and even mental confusion or momentary memory loss. It may also lead to delayed or premature actions, pauses in operation, or improper correction times, all of which are unsafe factors that can easily cause road traffic accidents. Therefore, driving while fatigued is strictly prohibited.
Was this review help?
15
2
Share
More Forum Discussions

How to Fix a Loose Manual Gear Stick?

To fix a loose manual gear stick, simply replace the gear shift rubber boot. The causes of a loose manual gear stick include: 1. Damaged transmission: The transmission needs to be replaced. 2. Wear and looseness: The plastic washer at the linkage joint between the gear stick and the transmission is worn or the screws are loose. Information about manual transmissions is as follows: 1. Manual transmission: Also known as a manual gearbox, it is a type of transmission and the most basic type in automotive transmissions. 2. Function: Its role is to change the gear ratio, also known as the gear ratio. Based on the principle of leverage, it uses the largest diameter low-speed gear with the longest radius to amplify the engine torque, assisting the vehicle in starting to move forward.
4
0
Share

How to Align the Timing Marks for Chang'an Star Timing Belt?

Introduction to aligning the timing marks for Chang'an Star timing belt: The crankshaft gear mark is a dot, and there are two dots on the camshaft. Align these three dots in a straight line. Ensure the crankshaft is at the top dead center, or refer to the timing cover mark where the arrow points to the dot, aligning them in a straight line. Below is some related information about the Chang'an Star: 1. Safety Features: The Chang'an Star features a protruding front end with a collision buffer frame to reduce driver injury in collisions and ensure driving safety. The front wheels are positioned forward to decrease the impact of frontal collisions, and the front doors are equipped with anti-collision bars for effective resistance against side impacts. 2. Comfort Features: The front seats of the Chang'an Star can slide forward and backward, and the backrest angle is adjustable, accommodating drivers of different sizes and heights. The middle row seats have adjustable backrest angles for enhanced comfort. The rear seats can be folded to increase cargo space, making it easier to transport large luggage. The engine uses full-floating support technology to effectively block noise and vibrations from the muffler.
14
0
Share

Solutions for Oil Burning in 2012 Malibu

Here are the detailed explanations of the causes and solutions for oil burning in the 2012 Malibu: 1. Piston seal abnormality: Excessive clearance between the piston and cylinder wall causes oil to splash into the combustion chamber during piston movement. Solution: Replace with slightly more viscous oil to enhance sealing. 2. Oil blockage: Aging or failure of the valve stem seals allows oil to enter the combustion chamber through the gap between the valve stem and guide hole under the influence of intake manifold vacuum. Solution: Use tools like a syringe to extract excess oil.
2
1
Share

What are the training methods for mistakenly pressing the accelerator?

About the introduction of training methods for mistakenly pressing the accelerator and brake: 1. Familiarize yourself with traffic regulations before getting in the car. Strictly adhering to traffic regulations will significantly reduce the probability of accidents. The premise of obeying traffic regulations is to remember them. For beginners who are not familiar with vehicles, it is recommended to review traffic regulations knowledge before driving. 2. Choose a relatively closed environment for practice. Select a place with low traffic volume to practice driving, improve your road sense, and develop a sense of direction. Through practice, you can master the vehicle and reduce the probability of accidents. 3. The practice area should be far away from water bodies. If the vehicle is too close to water and the speed is too fast, mistakenly pressing the accelerator instead of the brake can easily cause accidents. Stay away from water bodies and control the speed, continuously practice to improve your driving skills.
8
4
Share

Where is the problem when it's hard to shift gears in a manual transmission car?

Manual transmission cars are hard to shift gears due to problems with the following 5 parts: 1. Synchronizer is out of sync. 2. Damage to the car's gear teeth. 3. Incomplete clutch separation, with too little free travel. 4. Elastic loss of the separation lever. 5. Wear of the clutch plate. When driving, to adapt to road conditions and traffic flow changes to achieve a suitable driving speed, frequent gear changes are necessary. Here are introductions to several commonly used gears: 1. Low gear: The characteristic of low gear is a large speed ratio and slow driving speed, allowing the drive wheels to obtain greater torque and increase traction. Therefore, it is used in situations with high driving resistance such as starting, climbing steep slopes, or passing through difficult sections. However, low gear results in slow speed, high engine speed, easy engine temperature rise, and high fuel consumption. 2. Medium gear: Medium gear is a transitional gear from low to high or high to low. It is usually used when turning, crossing bridges, meeting other vehicles, on general slopes, or passing through generally difficult sections, but it is not advisable to drive in medium gear for a long time. 3. High gear: When road conditions are good, the engine has sufficient power, or the car load is light, high gear should be used. High gear provides fast driving speed, small traction, relatively high engine speed, low fuel consumption, and less engine wear, making it suitable for long-distance driving under good road conditions. 4. Reverse gear: Reverse gear allows the car to reverse or move in and out of garages. The essentials and timing of car gear shifting operations.
20
1
Share

How Do Colorblind People Obtain a Driver's License?

Colorblind individuals cannot obtain a driver's license. The following are the physical requirements for applying for a motor vehicle driver's license: 1. Height: Applicants for large buses, tractors, city buses, large trucks, or trolleybuses must be at least 155 cm tall. Applicants for medium-sized buses must be at least 150 cm tall. 2. Vision: For large buses, tractors, city buses, medium-sized buses, large trucks, trolleybuses, or streetcars, the naked or corrected vision in both eyes must reach 5.0 or above on the logarithmic visual acuity chart. For other vehicle types, the naked or corrected vision in both eyes must reach 4.9 or above. 3. Color vision: No red-green colorblindness.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.