Does BMW have a co-branded product with Puma?

What are the causes of steering gear noise in the BYD Tang?

BYD Tang steering gear noise may be caused by: lack of lubricating oil in the steering wheel screws; potential steering gear failure - turning the wheel to full lock places greater load on the steering mechanism, leading to severe wear and noise; insufficient tire pressure. Below are additional details: Solutions: For lack of lubricating oil in steering wheel screws, remove the steering wheel cover and add lubricating oil. If the steering gear is faulty, component inspection and replacement is recommended. Uneven tire pressure between left/right front tires can cause vehicle deviation, resulting in unbalanced wheel bearings, misaligned steering gear, and consequent noise and pulling.

13

3

Share

What is the Principle of Clutch?

Automobile clutch working principle: When the inner race is fixed, the outer race rotates clockwise and the wedge block does not lock, allowing the outer race to rotate freely. When the outer race rotates counterclockwise, the wedge block locks, preventing the outer race from rotating. Additional information: The clutch mainly consists of a driving disc, centrifugal throw-out blocks, buffer rubber rings, tension springs, pillar pins, and other components. The inner hole of the centrifugal throw-out block and the pillar pin are in dynamic fit, allowing the centrifugal throw-out block to swing around the pillar pin, while the tension spring always pulls the centrifugal throw-out block toward the smallest arc size. These components are all installed on the driving disc, which is fixed to the engine crankshaft. The rotation of the crankshaft drives the driving disc to rotate.

7

2

Share

How to Fold the Side Mirrors on the Atenza?

The electric folding knob for the Atenza's side mirrors is located near the electric window control buttons on the driver's side. The driver can fold the mirrors from inside the car, and the mirrors will automatically unfold when the vehicle is started. The side mirror folding function is divided into the following two types: 1. Manual folding: To fold the mirrors, you must reach out the window or get out of the car to fold them, which is both inconvenient and unsafe. This type of folding mirror is now less commonly used. 2. Electric folding: This type of folding mirror is now more common. Its advantage is that the mirrors can be folded from inside the car, and they will automatically unfold when the vehicle is started.

7

3

Share

How to Reset the Maintenance Light on Changan Lingxuan?

Changan Lingxuan maintenance light reset method: 1. Turn off the ignition switch to ensure the engine is off; 2. Press and hold the short-distance counter reset button below the tachometer; 3. Turn the ignition switch to the "ON" position, then release the short-distance counter reset button; 4. When the "SERVICE" indicator appears on the display, pull out the minute button on the clock; 5. Turn the minute button to the right until the mileage appears on the display; 6. Turn off the engine, and a reset confirmation message will appear; 7. Turn the ignition switch to the "ON" position again, and the "SERVICE" indicator will disappear, indicating the maintenance light has been successfully reset.

1

2

Share

How to Turn on the Volkswagen Air Conditioning?

Here is how to turn on the Volkswagen air conditioning: 1. There are three rotary buttons on the Volkswagen center console. The left button in blue represents cooling, red represents heating, and the middle one represents moderate temperature. 2. To turn on the cold air, adjust the left button towards the blue area. When heating is needed, adjust it towards the red area, then press the AC cooling switch. 3. The middle button controls the fan speed, mainly used to adjust the fan. Even when the AC is not turned on, it can still blow normal-temperature air. 4. The right button is used to adjust the air vents. If the windshield fogs up, you can adjust the vent to blow air onto the front windshield (semi-triangular icon with an airflow arrow).

10

5

Share

Where is the outdoor temperature sensor of the Besturn B50 located?

Water temperature sensors are installed on the water channels and radiator of the vehicle. Additional information: 1. Automotive water temperature sensor: Installed on the water jacket of the engine block or cylinder head, in direct contact with the coolant, used to measure the temperature of the engine's coolant. 2. Temperature sensor for the coolant temperature gauge: A negative temperature coefficient thermistor (NTC), whose resistance decreases as the temperature rises, with one wire connected to the electronic control unit (ECU). The other wire is a ground connection. 3. Working principle: The electronic control unit measures the temperature of the engine's cooling water based on this change; the lower the temperature, the higher the resistance, and vice versa, the lower the resistance.

6

3

Share

Does BMW have a co-branded product with Puma?

What are the causes of steering gear noise in the BYD Tang?

What is the Principle of Clutch?

How to Fold the Side Mirrors on the Atenza?

How to Reset the Maintenance Light on Changan Lingxuan?

How to Turn on the Volkswagen Air Conditioning?

Where is the outdoor temperature sensor of the Besturn B50 located?

Why Does the Engine Shake While Driving?

Where is the OBD interface located on the MG3?

Which car series does Roewe belong to?

What is the difference between Audi A6L45 and 55?