Does BAIC Senova Use Aisin Transmission?

1 Answers
Jasper
07/29/25 7:19pm
BAIC Senova uses Aisin transmission. Founded in 1969, Aisin is a world-renowned professional developer and manufacturer of automotive automatic transmissions. In the field of automotive automatic transmissions, Aisin's products hold the highest global market share. The BAIC Senova transmission employs a single-speed fixed gear ratio transmission. A transmission that changes vehicle speed through different gear ratios is called a fixed gear ratio transmission, which is also a type of electric vehicle transmission. With this design, power is directly transmitted from the motor to the transmission, which then delivers the power directly to the two wheels, reducing power loss. It also offers advantages such as simple structure, ease of manufacturing, and low production costs. When using the BAIC Senova transmission in daily driving, pay attention to the following points: Do not delay changing the transmission oil for extended periods. Prolonged failure to change the transmission oil can lead to damage to internal components such as bearings and the housing. Avoid prolonged coasting in neutral. While driving manual transmission vehicles, many experienced drivers may coast in neutral, but for automatic transmission vehicles, this can cause the transmission to overheat and may result in a noticeable jolt when shifting back into Drive (D) mode. Never shift into Drive (D) or Reverse (R) before the vehicle has come to a complete stop. Some drivers, aiming for smooth operation, may shift into reverse while the vehicle is still moving, which can cause significant damage to the transmission gears and, over time, lead to gear grinding and other failures. Avoid frequently climbing steep slopes in Drive (D) mode. When facing steep inclines, automatic transmission vehicles may overheat due to high load or shift prematurely, resulting in insufficient climbing power. In such cases, use manual mode to limit the gear to a lower speed or switch to sport mode to protect the transmission. Do not tow the vehicle over long distances. If an automatic transmission vehicle breaks down, use a flatbed tow truck to move the vehicle onto the tow platform while it is in Neutral (N) mode. Do not use a tow rope or similar method to directly tow the vehicle.
Was this review help?
8
0
Share
More Forum Discussions

Where is Rolls-Royce produced?

Rolls-Royce is produced in the UK and is one of the world's top ultra-luxury car manufacturers. It was founded in the UK in 1906, and in 2003, Rolls-Royce Motor Cars was acquired by BMW. Here is some relevant information: 1. Rolls-Royce is the sole symbol of elegance and nobility in the automotive kingdom. No matter how outdated the design or how high the cost, Rolls-Royce still has no challengers to this day. Rolls-Royce was officially established in the UK in 1906, and the Silver Ghost, launched the following year, was soon hailed as 'the best car in the world.' 2. The founders of Rolls-Royce were Charles Stewart Rolls and Frederick Henry Royce. The two had completely different backgrounds, hobbies, and personalities, but their dedication and aspiration for the automotive industry made them an outstanding partnership. Rolls died in a plane crash on July 12, 1910, and Royce passed away on April 22, 1933.
7
4
Share

Is There a Charge for Checking Fault Codes at a 4S Shop?

Whether checking fault codes at a 4S shop incurs a charge generally depends on the following two aspects: 1. If the vehicle is within the warranty period, fault detection at the 4S shop is usually free of charge. 2. If the warranty period has expired, fault detection at the 4S shop usually requires a fee. Below are the common practices of 4S shops when a vehicle experiences a fault: (1) Technicians typically use a diagnostic computer to read the fault codes first. The electronic systems in modern vehicles are highly advanced. If a fault occurs in any part of the car, the computer will generate a fault code. Technicians can read these codes with a diagnostic computer, which helps them quickly identify the cause and location of the fault. (2) If the fault code cannot be read with the computer, the technicians at the 4S shop will assess the possible faulty parts based on the symptoms described by the owner. They will then conduct a test drive and finally troubleshoot the issue.
12
0
Share

Do modern cars still need to be warmed up before driving in winter?

Modern cars still need to be warmed up before driving in winter. Since winter temperatures are much lower than other seasons, the engine warms up relatively slower. After starting the vehicle, friction occurs between the engine and various moving parts. If these components suddenly operate at high speeds, prolonged exposure to such conditions may cause damage. Therefore, warming up the car is essential. Here's the correct way to warm up your car in winter: After starting the vehicle, drive at low speeds. This prevents unlubricated components from undergoing intense operation that could lead to damage. During this time, simply maintain the engine speed at around 2000 RPM, and wait until the engine coolant reaches normal operating temperature before driving normally.
1
4
Share

What should be paid attention to when repairing the differential?

When repairing the differential, the following points should be noted: 1. First remove the oil filler hole screw and drain the lubricating oil inside the differential; 2. Use a hex wrench to first remove the small pressure cover, take off the bearing snap ring on the pulley seat, use a puller to remove the belt pulley, and then remove the pulley seat; then use the hex wrench to remove the left end cover of the differential, use a pry bar to take out the first-stage planetary carrier, then remove the first and second-stage differential housing, remove the right end cover, and take out the third-stage and second-stage planetary carriers; 3. Disassemble the first, second, and third-stage planetary carriers separately, clean and inspect all gears, bearings, and the inner sleeves of the planetary carriers. The surfaces should be free of wear, and the bearing clearance should be kept within the fixed range. If there is any wear, they must be replaced; 4. Clean and inspect. After disassembly, the differential housing and planetary gears must be thoroughly cleaned to ensure normal meshing between the gears; 5. During the disassembly and repair of the differential, hammering or striking is not allowed. The integrity of the parts must be ensured. If necessary, a copper hammer or copper rod can be used; 6. The platform for repairing the differential must be covered with a rubber mat to prevent hard contact between parts.
7
1
Share

Which is Faster: Automatic or Manual Transmission?

Whether a manual transmission accelerates faster than an automatic transmission depends on the specific type of transmission: 1. CVT transmission: Manual transmission accelerates faster than automatic. 2. Dual-clutch transmission: Automatic transmission accelerates faster than manual. Below are the differences between manual and automatic transmissions: 1. Different levels of operational difficulty: Manual transmissions are suitable for skilled drivers; automatic transmissions are suitable for beginners. 2. Different structures: Manual transmissions have a clutch; automatic transmissions do not. 3. Characteristics of manual transmissions: Quick response, stable performance, good fuel economy, and strong power. 4. Characteristics of automatic transmissions: Extends the lifespan of components, improves vehicle performance, and reduces air pollution.
9
0
Share

Should Vehicle Maintenance Be Based on Mileage or Time?

Whether to perform maintenance based on time or mileage generally follows the principle of whichever comes first. There is no fixed answer, as car owners need to analyze their vehicle's specific conditions to determine the optimal approach. Here is a brief introduction to vehicle maintenance: (1) Routine Maintenance: Typically performed every 5,000KM (or 7,500KM for some models), it mainly involves changing the engine oil and oil filter, inspecting the fuel filter (many modern vehicles no longer have one), and checking the air filter—replacing them if excessively dirty. Additionally, each maintenance session must include an inspection of the brake discs and pads for potential replacement, checking the brake fluid level, and assessing tire conditions to ensure safety. (2) Periodic Maintenance: Usually conducted every 3 years or every 40,000KM. Beyond routine maintenance, it includes cleaning the fuel injectors, throttle body, and the vehicle's intake system. Furthermore, it requires replacing transmission fluid, front and rear axle oil, coolant, and brake fluid. Tire wear should also be inspected, with replacements made if necessary. (3) Major Maintenance: Typically occurs after the vehicle has traveled 100,000KM, involving a comprehensive inspection and replacement of parts as needed. Special attention should be paid to the wiring (electrical circuits) and transmission mechanisms during this phase.
8
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.