Does a Tire Making Noise When Running Over Stones Have Any Impact?

1 Answers
MacMarley
07/30/25 1:22am
Tire noise when running over stones is generally caused by the sound of the stones being flicked away and usually has no impact. Below are some precautions for tire usage: 1. Check wear and tire pressure: Before heading out on highways or long trips, inspect the tire's wear and pressure. In summer, pay special attention to tire pressure and temperature. If any abnormalities are found, take effective measures promptly. 2. Remove foreign objects: Regularly clean out debris from the tire tread grooves and between the tires to prevent sharp objects from damaging the tires, which could lead to air leaks or even blowouts. 3. Punctures: If a tire gets punctured by a nail while driving, do not pull the nail out directly, as this could worsen the air leak and prevent the vehicle from continuing. Instead, maintain low-speed driving if a tire is punctured by a nail.
Was this review help?
8
3
Share
More Forum Discussions

What Causes Abnormal Noise When Turning On the AC in a Car?

The reasons for abnormal noise when turning on the AC in a car include belt slippage, air conditioning compressor failure, or foreign objects in the air ducts. Below are detailed explanations: 1. Belt Slippage: The air conditioning compressor is driven by the engine crankshaft via a belt. If the belt becomes loose, aged, severely worn, or if the tensioner lacks sufficient tension, it can cause the belt to slip, resulting in abnormal noise. If the issue is due to the belt, simply replacing the belt will suffice. If the problem lies with the tensioner, then the tensioner needs to be replaced. 2. Air Conditioning Compressor Failure: When the AC switch is turned on, the air conditioning compressor starts operating. If the compressor is damaged, it may produce abnormal noise. In such cases, it is recommended to visit a 4S shop for part replacement and repair. 3. Foreign Objects in the Air Ducts: If there are foreign objects in the air conditioning system's ducts, these objects can rotate with the blower's airflow and repeatedly hit the air filter, causing abnormal noise. In this situation, the air filter can be removed, and the air ducts should be carefully inspected and cleaned of any foreign objects.
9
5
Share

What Causes the Exclamation Mark on the Dashboard?

An exclamation mark light on the dashboard can be caused by issues with the braking system, low tire pressure, or steering system malfunctions. When this light appears, drivers should promptly identify the cause and take appropriate action. Braking System Malfunction: When this light is illuminated, it indicates severe wear or failure of the brake pads, low or degraded brake fluid levels, or a parking brake issue. Solutions include checking for brake fluid deficiency, inspecting for leaks in the brake calipers, pipelines, and connectors, examining the master and slave cylinders for damage, and replacing the brake pads if necessary. Low Tire Pressure: The tire pressure warning light may illuminate due to punctures causing air leaks, system-detected excessive tire pressure, or insufficient tire pressure. Solutions involve inflating the tires to the recommended pressure if they are underinflated or releasing air to the appropriate level if overinflated. Steering System Malfunction: This warning light indicates wear in steering system components or issues with electrical circuits or hydraulic lines. Common symptoms include heavy steering, unusual noises during steering, steering wheel vibrations, and poor steering wheel return capability. Solutions include timely inspection and repair at a service center, replacing faulty components, and checking the electrical circuits for proper functioning.
7
5
Share

What is the horsepower of the Yuexiang V3?

There are two models, with the 1.3L variant producing 94 horsepower and the 1.4L variant producing 101 horsepower. Below are the detailed specifications of the Yuexiang V3: 1. The Yuexiang V3 is a compact car with a small and agile body. 2. The wheelbase of the Yuexiang V3 is 2410 mm, with dimensions of 4200 mm in length, 1650 mm in width, and 1465 mm in height. 3. The 1.3L naturally aspirated engine of the Yuexiang V3 has a maximum torque of 121 Nm. This engine reaches its maximum power at 6000 rpm and its maximum torque between 4000 to 5000 rpm. It features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. This engine is paired with a 5-speed manual transmission. 4. The 1.4L naturally aspirated engine of the Yuexiang V3 has a maximum torque of 135 Nm. This engine reaches its maximum power at 6000 rpm and its maximum torque between 3500 to 4500 rpm. It also features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. This engine is paired with a 5-speed manual transmission.
9
2
Share

What is the difference between low-range 4WD and high-range 4WD?

4L stands for low-range four-wheel drive. The transfer case has a larger gear ratio, which amplifies torque while reducing speed, thereby increasing power. It is suitable for extremely harsh road conditions. 4H stands for high-range four-wheel drive, where the transfer case has a smaller gear ratio, allowing for relatively higher speeds but with less guaranteed power. It is suitable for general light off-road conditions. Below are relevant details: 1. Part-time four-wheel drive is a system where the driver can manually switch between two-wheel drive and four-wheel drive. By engaging or disengaging the transfer case, the driver can achieve either two-wheel or four-wheel drive based on driving needs. This is the most common four-wheel drive system found in off-road vehicles or SUVs with 4WD capability. 2. Part-time four-wheel drive systems typically have three modes: 2H, 4H, and 4L (switched via the transfer case), commonly referred to as two-wheel drive, high-range four-wheel drive, and low-range four-wheel drive. Two-wheel drive mode is more suitable for city roads or paved surfaces. High-range four-wheel drive is ideal for gravel roads, while low-range four-wheel drive is best used for off-road climbing or recovery situations. Switching can be done via a traditional gear lever, buttons, or a rotary knob.
2
0
Share

What is Engine Compression Ratio?

Engine compression ratio refers to the ratio of the volume of the air-fuel mixture before compression to its volume after compression in the combustion chamber. A higher engine compression ratio generally indicates stronger power output. Below is an explanation of engine compression ratio: 1. When the compression ratio is higher, the air-fuel mixture reaches a higher temperature after compression. When ignited by the spark plug, the mixture combusts almost instantaneously, releasing more energy and delivering greater power output. 2. With a lower compression ratio, the compressed air-fuel mixture remains at a relatively lower temperature. The spark plug takes longer to complete the combustion process, and additional energy is required to raise the mixture's temperature. As a result, power output decreases, and some energy is converted into heat, causing the engine temperature to rise instead of contributing to the vehicle's forward motion. 3. In summary, a higher compression ratio generally leads to better engine efficiency, improved performance, and superior fuel economy. However, an excessively high compression ratio is not necessarily better. If the compression exceeds the engine's capacity, abnormal combustion may occur on surfaces such as the combustion chamber walls, exhaust valve heads, spark plug electrodes, or carbon deposits. This surface ignition phenomenon generates extremely high pressure, significantly increasing the load on engine components and drastically reducing their service life. Therefore, the optimal engine compression ratio should be moderate rather than excessively high.
9
1
Share

Why is the clutch pedal of a van heavy to press?

Here are the specific reasons why the clutch pedal of a van is heavy to press: 1. Dirty hydraulic oil in the clutch master and slave cylinders and pipelines: Or deterioration of the rubber cups and sealing rings, or blockage in the oil lines. Disassemble the clutch master and slave cylinders and pipelines, clean them thoroughly with alcohol, and blow them clean with high-pressure air, especially the pipelines. Replace the rubber cups and rings of the master and slave cylinders, bleed the air, and adjust the clearance according to specifications. 2. Issues with the release bearing: Excessive resistance caused by prolonged use, severe wear, and lack of lubrication. Faults in the pressure plate, clutch pressure plate, or release bearing—these components are wear parts. If they are faulty or severely worn, the clutch may become heavy.
14
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.