Do Tubeless Tires Also Need Inflation?

2 Answers
DiMadison
07/29/25 4:27am
Tubeless tires do require inflation. Tubeless tires do not have an inner tube, and the tires used on cars are all tubeless. Tires are a crucial component of a vehicle, directly impacting driving stability and safety. They are the only part of the car that makes contact with the ground. Being made of rubber, tires are subject to wear and aging over time, necessitating regular replacement. Tubeless tires, also known as low-pressure or pneumatic tires, offer high elasticity, excellent wear resistance, good traction, and effective heat dissipation. Their use is increasingly widespread in bicycles, motorcycles, cars, buses, and trucks.
Was this review help?
6
0
Share
DelDeclan
08/12/25 8:10am
A veteran mechanic with over a decade of experience tells you that tubeless tires definitely need air! These rely entirely on the tight seal between the tire bead and the wheel rim to prevent air leakage. The worst scenario is when drivers assume tubeless tires don’t require pressure maintenance, leading to cracked sidewalls from prolonged neglect. Just last week, I repaired a car with its right front tire at only 1.2 bar—the shoulder was worn down to the steel belts. Summer demands extra attention: for every 10°C temperature rise, tire pressure increases by 0.1 bar. Always check before highway drives. Keep a mechanical pressure gauge in your glovebox and test regularly, maintaining 2.2-2.5 bar for optimal safety.
Was this review help?
10
5
Share
Expand All
More Forum Discussions

What are the steps to remove the dashboard of a Volkswagen Polo?

Pry off the black trim frame around the head unit, being careful not to use excessive force to avoid breaking the frame. Remove the fixing screws around the head unit, taking care not to drop the screws into the gaps of the center console. Disconnect the wiring harness at the back. Connect the wiring harness of the head unit to the new head unit. These are specialized connectors, so there's no need to worry about incorrect connections. After installing the new head unit, power it on for testing. Once the test is successful, tighten the screws to secure it, and finally reattach the black trim frame.
15
5
Share

How to Remove and Replace a Seat Belt Buckle?

First, adjust the seat and remove the four fixing bolts on the front and back of the seat. Locate the wiring of the car seat and disconnect the sensor wire of the seat belt buckle. Remove the seat cushion, take off the seat airbag, then remove the bolt fixing the seat belt, and finally take out the seat belt buckle slot. Remove the sensor inside the seat cushion, install the new seat belt buckle slot onto the seat, connect the wiring, and tighten the bolts. Install the weight sensor and the new retractor onto the seat, and tighten them with a wrench.
20
3
Share

What is the method to reset the maintenance light on a Mercedes-Benz W221?

Turn the ignition switch to the first position. Simultaneously press and hold the 'OK' button (S110s6) on the multifunction steering wheel and the 'Answer/End' button on the right side for about 5 seconds. Select 'ASSYSTPlus workshop' and confirm by pressing the 'OK' button (S110s6). Use the 'Forward/Backward' button (S110s1) to select 'Service Performed' and confirm by pressing the 'OK' button (S110s6). Choose 'Complete (Full) Service' or 'Individual'.
6
1
Share

How to Repair Gear Slippage in a Tiller?

Gears only partially engage in width, the locking steel ball does not snap into the locking groove of the shift rail, or the shift lever end is severely worn. When the axial force on the gear exceeds the locking force generated by the locking spring, the sliding gear is pushed away, resulting in automatic gear disengagement. If the shift fork is deformed or severely worn, and the centerline of the sliding gear intersects at an angle with the shaft centerline, the sliding gear may move axially and disengage. Severe wear of the steel ball or positioning groove can also make it difficult to position the sliding gear during transmission, leading to gear disengagement. Bearing wear increases the clearance, causing a skewed thrust during gear engagement, which results in gear disengagement.
2
2
Share

How to Install the Intake Camshaft on BMW N46 Engine?

Before installing the camshaft, first install all bearing caps and check if the camshaft holes are misaligned. When installing the camshaft, the cam of cylinder 1 must face upwards without pressing the valves. First, tighten the bearing caps of the 2nd and 5th positions alternately in a diagonal pattern with a torque of 20 Nm, then install the bearing caps of the 1st and 3rd positions, and finally install the bearing cap of the 4th position. Install the camshaft half-moon key and timing gear, tighten the bolts to prevent camshaft sliding and reduce risks, with a torque of 80 Nm.
2
0
Share

Where is the engine of the 2021 RAV4 produced?

2021 RAV4's engine is domestically produced, with some components being imported. The engine model used in the 2021 RAV4 is the M20D-FKS, with a maximum horsepower of 171, maximum power of 126KW, maximum power speed of 4400-5000rpm, and peak torque of 209N.m. The vehicle's power performance is relatively smooth and has been known for its low fuel consumption and low maintenance costs. For the 2021 RAV4's engine, the following maintenance methods can be used daily: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected based on mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid faults, change the oil regularly based on usage conditions and keep the oil level moderate. When engine oil passes through the fine holes of the filter, solid particles and sticky substances in the oil accumulate in the filter. If the filter is blocked and the oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to pass through the bypass valve and bring dirt back to the lubrication parts, accelerating engine wear and internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, blocking the filter and oil holes, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine works properly but also extends the overall lifespan of the radiator and engine.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.