Do Rear Seats Need to Wear Seat Belts?

1 Answers
JasperLee
07/29/25 9:27pm
Rear seats do need to wear seat belts. Here are the specific functions of car seat belts: 1. Protect passengers' safety: Car seat belts can protect passengers' safety, especially when driving on highways, where rear seats must wear seat belts. A seat belt buckle is a device that can be inserted into the car's seat belt socket, preventing the seat belt warning alarm from sounding when the driver is not wearing the seat belt. 2. Ensure driving safety: Seat belts are the only guarantee for the driver's safety while driving. Even when the car is traveling at relatively low speeds, in the event of a collision or emergency braking, although the generated inertial force is relatively small, it is still enough to make the driver and passengers lose control of their bodies, colliding with hard components such as the steering wheel and windshield, causing physical harm.
Was this review help?
15
0
Share
More Forum Discussions

Where does the Lu R license plate belong?

Lu R license plate belongs to Heze City, Shandong Province. The license plates of Shandong Province are as follows: Lu A is Jinan, Lu B is Qingdao, Lu C is Zibo, Lu D is Zaozhuang, Lu E is Dongying, Lu F is Yantai, Lu G is Weifang, Lu H is Jining, Lu J is Tai'an, Lu K is Weihai, Lu L is Rizhao, Lu M is Laiwu, Lu N is Dezhou, Lu P is Liaocheng, Lu Q is Linyi, Lu R is Heze, Lu U is Qingdao Development Zone. License plates, commonly known as car plates, refer to vehicle registration plates, which are plates hung on the front and rear of a vehicle. They are usually made of aluminum, iron, plastic, or paper, and display the vehicle's registration number, registration region, or other relevant information.
19
0
Share

What are the troubleshooting steps for Hyundai P0016 fault code?

Here are the troubleshooting steps for Hyundai P0016 fault code: 1. Disconnect both battery terminals, wait for a few minutes, then reconnect and test drive the vehicle. 2. If the vehicle still shows no response, consider replacing the sensor. 3. If replacing the sensor doesn't resolve the issue, take the vehicle to a professional repair shop for major repairs. Below is additional information about P0016: 1. The crankshaft converts the piston's linear motion into rotational motion. 2. The camshaft controls the opening and closing of valves. 3. The Engine Control Unit (ECU) continuously monitors the variable camshaft's timing position to check for misalignment between camshaft and crankshaft. 4. If this misalignment exceeds one gear tooth, this fault code will appear. 5. Contaminated engine oil or a stuck variable camshaft solenoid valve may also trigger this fault code.
1
0
Share

What brand is the BMW e39 audio system?

BMW e39 audio system is B&O audio. B&O audio: The B&O high-end surround sound system features 16 fully integrated speakers with a total power output of 1200 watts, delivering top-tier music quality. Owners can select different sound modes: "Studio" mode offers crystal-clear sound, while "Expanded" mode creates a more ethereal audio experience, delivering unparalleled surround sound. Car audio: Car audio (autoaudio) is a system designed to alleviate the monotony of travel for drivers and passengers. Initially, car AM radios were used, followed by AM/FM radios, tape players, and later CD players compatible with DCC and DAT digital audio. Today's car audio systems meet high standards in sound quality, operation, and vibration resistance, ensuring stable performance and perfect sound quality even on rough roads.
19
5
Share

Must the Tensioner Pulley Be Replaced When Changing the Belt?

If the water pump is driven by the timing belt, it is generally recommended to replace it along with the timing belt, tensioner, and tensioner pulley. If it is not driven by the timing belt, replacement is not necessary. Reasons for replacing the timing belt: The timing belt has a limited lifespan, and if it breaks, it may cause damage to the valves, pistons, and cylinder head. The repair costs in such cases can be very high. Therefore, it should be replaced periodically. Introduction to the tensioner pulley: The car generator tensioner pulley is used in the belt tensioning device of the transmission system. It mainly consists of a fixed housing, tensioning arm, pulley body, torsion spring, rolling bearing, and spring bushing. It automatically adjusts the tension force according to the belt's tightness, ensuring the transmission system remains stable, safe, and reliable.
20
1
Share

What are the differences between the 2019 Kodiaq and the 2019 facelift model?

The differences between the 2019 Kodiaq and the 2019 facelift model are: 1. Different infotainment screen sizes: The 2019 Kodiaq has a 9-inch screen, while the 2019 facelift model has an 8-inch screen. 2. Different external audio source interfaces: The 2019 Kodiaq supports USB, AUX, and SD, while the 2019 facelift model only supports USB. More relevant information is as follows: Both the 2019 Kodiaq and the 2019 facelift model feature a 5-door, 7-seat SUV body structure. Their dimensions are identical: length 4698mm, width 1883mm, height 1676mm, with a wheelbase of 2791mm, front track of 1582mm, rear track of 1572mm, fuel tank capacity of 62.5 liters, luggage capacity ranging from 190 to 2065 liters, and a curb weight of 1775kg.
13
0
Share

What are the causes of chassis noise in the Mercedes-Benz GL350?

Chassis noise in the Mercedes-Benz GL350 may be caused by universal joint failure in the driveshaft, noise in the braking system, wheel bearing noise, clutch noise, and other reasons. Below are the specific details: Universal Joint Failure in the Driveshaft: Due to damaged dust covers and oil leakage not being repaired in time, the small bearings wear abnormally. Braking System Noise: Loose brake pads or calipers; noise caused by faulty brake pads or brake discs. Wheel Bearing Noise: Due to abnormal wear or burning of the bearings, a "humming" sound may occur at certain speeds, and this sound increases as the speed rises. Clutch Noise: The clutch release bearing lacks lubrication and has abnormal wear, so when the clutch pedal is pressed, noise occurs, and the noise disappears when the pedal is released.
2
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.