Do I still need to undergo an annual review of my driver's license after deducting points through legal studies?

What are the reasons for the failure of car power windows to move up and down?

Solutions for power windows that cannot move up and down: 1. Reset the window lifting system: Generally, the inability of car windows to move up and down is caused by the disconnection of the battery, or the power or ground wire of the window control module being disconnected during vehicle maintenance. This can be resolved by resetting the window lifting system. Start the car, operate the window switch, hold the switch for more than 3 seconds after the window reaches the top, then release and immediately press and hold the switch again to initialize the window lifting system. If you are unsure, it is recommended to seek professional technical assistance. 2. Clean the dirt in the glass guide channel: If the car glass is tilted or difficult to move up and down, it may be due to excessive dust or dirt in the glass guide channel, increasing resistance during the lifting process. The owner can use a wet towel wrapped around chopsticks to clean inside the guide channel by moving it up and down, and continuously wash the towel to remove the dirt until the guide channel is clean. After cleaning, check if the window glass returns to normal operation. 3. Directly replace the window regulator switch: The window glass switch is used frequently and is more likely to be damaged. If the glass cannot move up and down, the car window regulator can be replaced. Those with strong DIY skills can replace it themselves, but it is still recommended to visit a 4S shop for replacement.

9

5

Share

Does Every Car Have a Three-Way Catalytic Converter?

Not all cars are equipped with a three-way catalytic converter. In the early years in China, vehicles produced that did not meet the National II emission standards lacked this component. The three-way catalytic converter is an external purification device installed in the vehicle's exhaust system. It converts harmful gases such as CO emitted from the car's exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions. Below are the reasons for the failure of a three-way catalytic converter: Excessive Temperature: At room temperature, the three-way catalytic converter does not possess catalytic capabilities. Its catalyst must be heated to a certain temperature to gain oxidation or reduction abilities. Typically, the light-off temperature of the catalytic converter ranges between 250–350 degrees Celsius, with normal operating temperatures generally between 400–800 degrees Celsius. During operation, the catalytic converter generates a significant amount of heat, and higher loads result in higher oxidation temperatures. When the temperature exceeds 1,000 degrees Celsius, the catalyst coating inside can sinter and fail, also increasing the risk of vehicle fires. Therefore, it is crucial to control factors that cause exhaust temperature to rise, such as delayed ignition timing, misfiring, or incorrect ignition sequences, as these allow unburned fuel mixture to enter the catalytic converter, leading to excessively high exhaust temperatures and impairing its efficiency. Chronic Poisoning: The catalyst is highly sensitive to elements such as sulfur, lead, phosphorus, and zinc. Sulfur and lead originate from gasoline, while phosphorus and zinc come from lubricating oil. These four substances, along with their oxide particles formed during combustion in the engine, tend to adhere to the catalyst's surface, preventing it from contacting exhaust gases and thus losing its catalytic function—a phenomenon known as poisoning. Carbon Buildup: When a car operates under low-temperature conditions for extended periods, the three-way catalytic converter cannot activate, and carbon particles from the engine exhaust adhere to the catalyst's surface. This prevents contact with CO and HC, eventually clogging the converter's pores and reducing its conversion efficiency. Exhaust Deterioration: The catalytic converter has a limited capacity for pollutant conversion, so it is essential to minimize raw emissions through internal purification technologies. If the concentration or total volume of exhaust pollutants is too high—such as an overly rich air-fuel mixture—it can impair the catalytic converter's ability to transform pollutants, lowering its efficiency. Additionally, when excessive amounts of HC and CO enter the catalytic converter, they trigger intense oxidation reactions, generating excessive heat that can damage the converter due to overheating.

11

2

Share

Can a Seized Car Still Be Driven?

A seized vehicle can still be driven if it is not under impoundment, and it can undergo normal annual inspections and insurance payments. However, it cannot be sold, mortgaged, or repurposed for other uses. Below are the specific reasons: Legal Basis for Driving a Seized Vehicle: According to Order No. 124 of the Ministry of Public Security, it explicitly prohibits certain vehicle-related procedures during the seizure period, such as registration, modification, transfer, mortgage release, deregistration, and pledge release. However, it does not prohibit annual inspections, temporary license plates, or replacement of license plates and certificates. The "Road Traffic Safety Law" does not stipulate that seized vehicles are prohibited from being driven on the road. Additionally, based on the nature of seized vehicles, a car that is merely seized can still be driven legally. Cases Where a Seized Vehicle Cannot Be Driven: If the vehicle is both seized and impounded, it cannot be driven on the road. Methods to Lift the Seizure: If a seized vehicle is not resolved within the stipulated time, it may be locked at any time. As long as the seized vehicle is not physically impounded, it can still be driven, but changes or transfers are not allowed. To lift the seizure, the respondent must fulfill the judgment or provide other guarantees. If the judgment has been fully executed, an application can be made to the court to lift the seizure. Once the court issues a release ruling, the ruling document can be taken to the vehicle management office to complete the release process.

8

2

Share

What is the 525 car?

525 is a BMW car. BMW, the full Chinese name being Bavarian Motor Works Co., Ltd., is a German luxury car brand. BMW's vehicle series include the i, X, Z, and pure number 4 models, as well as the 1, 2, 3, 4, 5, 6, 7, and 8 series. Below is an introduction to BMW cars: Logo meaning: B.M.W. stands for Bavarian Motor Works, and the colors and combination of the logo come from the state emblem of Bavaria, where BMW is headquartered. Brand honors: On December 18, 2018, the "2018 World Brand 500" compiled by the World Brand Laboratory was announced, with BMW ranking 16th.

7

0

Share

What does 50cc mean?

50cc refers to an engine displacement of 50 milliliters or 50 cubic centimeters. The maintenance methods for car engines are as follows: Regularly change the engine oil and filter: The quality of any grade of lubricating oil will change during use. To avoid malfunctions, it is necessary to change the oil regularly based on usage conditions and maintain an appropriate oil level (generally up to the upper limit of the oil dipstick). Regularly clean the radiator: Rust and scale can restrict the flow of coolant in the cooling system, reducing heat dissipation and causing the engine to overheat, which may even lead to engine damage. Therefore, the radiator should be cleaned regularly to remove rust and scale. Regularly clean the crankcase: During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. Hence, the crankcase should be cleaned regularly to maintain the cleanliness inside the engine.

16

3

Share

Do 50cc motorcycles require license plates?

50cc motorcycles require license plates. According to regulations, motorcycles with a displacement below 50CC are classified as mopeds, which also need to be licensed and require a driver's license. The fact that many mopeds in various areas are unlicensed is an issue of management, not an indication that licensing is unnecessary. Below is an introduction to mopeds: Definition and standards of mopeds: Regardless of the driving method, the maximum design speed of a moped must not exceed 50km/h. If powered by an internal combustion engine, the displacement must not exceed 50ml; if electrically driven, the total rated output power of the motor must not exceed 4KW. Requirements for driving a moped: The driver must be at least 16 years old, with a height of 1.45 meters or more, vision of 0.7 or above (or corrected to 0.7 or above), no red-green color blindness, normal hearing, and no physical defects or diseases that could hinder safe driving. After passing a medical examination and the traffic rules and driving skills tests administered by the public security authorities, a moped driver's license will be issued. For licensed mopeds, a medical examination is required every two years, and those who fail are not permitted to continue driving.

4

3

Share

Do I still need to undergo an annual review of my driver's license after deducting points through legal studies?

What are the reasons for the failure of car power windows to move up and down?

Does Every Car Have a Three-Way Catalytic Converter?

Can a Seized Car Still Be Driven?

What is the 525 car?

What does 50cc mean?

Do 50cc motorcycles require license plates?

Is Car Chassis Soundproofing Effective?

Why is the car charging the phone slowly?

Should You Engage the Handbrake or Shift to Neutral First After Stopping in Driving Test Part 3?

How Many Models Does the Haval Chitu Have?