Do I still need to queue if I switch from gasoline vehicle lottery to electric vehicle lottery?

1 Answers
SanAbigail
07/29/25 11:57pm
Switching from gasoline vehicle lottery to electric vehicle lottery also requires re-queuing without priority. New energy vehicle quota holders can only renew new energy vehicle quotas when updating their indicators. Similarly, regular passenger car quota holders can only renew regular passenger car quotas when updating their indicators. The two cannot be interchanged. Therefore, if a new energy vehicle user wants to switch to a regular passenger car, they must first sell or scrap the new energy vehicle under their name to meet the application condition of having no passenger car registered under their name, and then re-enter the lottery for regular passenger cars. The same applies when switching from regular vehicles to new energy vehicles. Car lottery applicants can switch between the regular vehicle and new energy vehicle lottery pools, but for each lottery round, applicants can only choose one type to apply for. They cannot apply for both types of quotas simultaneously in the same round. Additionally, since the tiered winning probability for regular passenger cars is based on the cumulative number of lottery participations, switching from regular vehicle to new energy vehicle application will not cause an interruption, and the cumulative tiered winning probability will remain unaffected. Operation steps: Confirm whether you meet the application requirements; Submit the application; Obtain the application code and participate in the lottery; Check the lottery results and the passenger car allocation quota confirmation notice; Purchase a vehicle using the quota code.
Was this review help?
15
5
Share
More Forum Discussions

How to Properly Jump Start a Car?

Correct method for jump starting a car: 1. Connect the red clamp to the positive terminal of the dead battery, then connect the other end of the red cable to the positive terminal of the booster car; 2. Connect the black clamp to the negative terminal of the booster car, then connect the other end of the black cable to the negative terminal of the dead battery or a suitable grounding point. Precautions for jump starting: 1. Keep the booster car running, and start the dead car normally after completing the jump start procedure; 2. When possible, it's recommended to let the revived car run for more than half an hour to ensure sufficient charging; 3. Avoid contact between positive and negative terminals and ensure correct polarity connection during jump starting.
10
0
Share

What maintenance items should be done for a family sedan at 60,000 kilometers?

The thermostat of the Magotan is located inside the plastic pipe at the interface of the upper and lower water pipes, and it is integrated. Working principle of the thermostat: The thermostat automatically adjusts the amount of water entering the radiator based on the temperature of the coolant, changing the circulation range of the water to regulate the heat dissipation capacity of the cooler and ensure the engine operates within the appropriate temperature range. The thermostat must be kept in good technical condition; otherwise, it will seriously affect the normal operation of the engine. Too late and too early: If the main valve of the thermostat opens too late, it will cause the engine to overheat; if the main valve opens too early, it will prolong the engine warm-up time, causing the engine temperature to be too low.
3
4
Share

What Causes Noise in the Steering Gear?

Reasons for noise in the steering gear: Lack of Lubrication: If there is a lack of lubrication in the screws inside the steering wheel, you need to remove the steering wheel cover and add lubricating oil. This should allow smooth movement in the track and pivot areas. Steering Gear Malfunction: The steering gear might also malfunction. Normally, if the steering wheel is turned too sharply while turning, it puts a greater load on the steering gear, leading to severe wear and resulting in abnormal noises. It is recommended to inspect and replace the faulty components. Insufficient Tire Pressure: Uneven tire pressure in the left front or right front tire can cause the car to pull to one side, leading to unbalanced wheel bearings, misaligned steering gear, and resulting in abnormal noises and pulling.
14
5
Share

What to Do When the Tachometer Needle Fluctuates During Cold Start?

Solutions for fluctuating tachometer needle during cold start are as follows: 1. Check the throttle valve: Inspect if the throttle valve is excessively dirty, clean and recalibrate it. 2. Inspect the intake system: Check for excessive carbon buildup in the engine intake system and fuel injectors. Perform a no-disassembly cleaning and replace the fuel filter. Note: For gasoline engines, when the ambient temperature is not lower than -5°C, and for diesel engines, when the ambient temperature is not lower than 5°C, up to three start attempts (including three) are allowed, with each attempt not exceeding 5 seconds, and the engine must start successfully. Under normal operating temperature, the engine should start successfully within 5 seconds in one attempt. After a cold start, the engine warm-up process should comply with the original design specifications regarding RPM.
15
1
Share

What is the gear ratio of a transmission?

Gear ratio refers to altering the gear ratio of the vehicle's main reducer. All vehicle rear axles are equipped with a reducer, which reduces the rotational speed from the driveshaft. The gear ratio is the transmission ratio—for example, if the driveshaft rotates at 4.1 r/s, it will be reduced to 1 r/s. The relationship between gear ratio and torque: The larger the gear ratio, the greater the output torque and the slower the output speed; the smaller the gear ratio, the smaller the output torque and the faster the output speed. Common applications of gear ratio: To achieve greater power (torque) output for climbing hills or heavy loads, selecting a relatively larger main gear ratio (such as 6.833) can meet the demand, but it also sacrifices vehicle speed.
1
1
Share

Where is the fuel pump located on the BMW X5?

The high-pressure fuel pump of the BMW X5 is located on the engine block, while the fuel pump is situated under the right rear seat. The fuel pump is a lightweight and compact device, categorized into three main types: in-line, distributor, and single-unit. The fuel pump requires a power source to operate, with its lower camshaft driven by the engine crankshaft gear. Taking the 2021 BMW X5 as an example, its body dimensions are 4930mm in length, 2004mm in width, and 1776mm in height, with a wheelbase of 2975mm and a fuel tank capacity of 83 liters. This model is equipped with a 2.0T turbocharged engine, delivering a maximum power of 195kW and a maximum torque of 400Nm, paired with an 8-speed automatic transmission.
10
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.