···
Log in / Register

Do I need to wear glasses during the driving test if I didn't wear them during practice?

4 Answers
McSadie
09/02/25 4:14am
You don't need to wear glasses during the driving test if you didn't wear them during practice. Specific reasons: When applying for a driver's license, you need to submit new photos. As long as you have the license when driving, it's unrelated to whether you wear glasses or not. If you're concerned about visibility during the test, you can wear contact lenses. Wearing glasses is mainly to pass the physical examination. During the test, wear glasses if required, otherwise it's not necessary. Precautions during practice: When practicing at the driving school, students should pay attention to the proper way of holding the steering wheel, as well as the usage of brakes, clutch, and accelerator. Always fasten the seatbelt when getting in the car, and master the operation and use of vehicle lights.
Was this review help?
2
1
Share
EmmanuelAnn
09/14/25 6:28am
When I was learning to drive, I also thought it was convenient not to wear glasses, especially in the slow and close-range practice area where it was easy to see clearly. However, before the test, a check revealed my vision was only 4.7, below the standard. I passed the vision test during the exam by wearing glasses, but later realized the risks of driving without them on highways—distant headlights appeared blurry. I strongly advise wearing glasses during the test, as examiners strictly check the vision chart. Failing means retaking the test, wasting both time and money. While you might slack off during practice, don’t take the formal test environment lightly.
Was this review help?
7
5
Share
Expand All
JulietteMarie
10/28/25 7:12am
After driving for so long, I understand that vision is the foundation of driving safety. The test requires passing a vision screening to proceed. You might have practiced without glasses out of habit, but the exam environment is unfamiliar and demands accurate judgment of distances and traffic light colors. Once, I almost rear-ended someone in the rain because I wasn't wearing my glasses, realizing then that daily negligence plants hidden dangers. The exam rules protect everyone—only meeting the vision standard can prevent accidents. It's best to get your vision tested before signing up for the exam; don't take the risk.
Was this review help?
6
3
Share
Expand All
LeEliza
12/11/25 7:26am
My buddy never wore glasses while practicing driving, thinking it was fine, but failed the vision test during the exam and had to reschedule. Later, he obediently got glasses and passed. The test requires clear vision to distinguish the colors of signs 20 meters away. You might get away with it in a small practice area, but don’t gamble with luck during the actual exam—it’s a waste of effort. Poor night vision while driving is even more dangerous, so it’s better to develop the habit of wearing glasses early to save trouble.
Was this review help?
8
5
Share
Expand All
More Forum Discussions

What engine does the Chevrolet Cruze have?

The engine of the Chevrolet Cruze is produced by Shanghai GM at the Yantai Dongyue Engine Company, utilizing General Motors' technology, thus making it an American-made engine. The Chevrolet Cruze uses the EcotecDVVT engine model, with a maximum power output of 110 kW, a maximum horsepower of 150, and a maximum torque of 240 Nm. For daily maintenance of the Chevrolet Cruze's engine, the following methods can be employed: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment in the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will deteriorate during use. After a certain mileage, performance degradation can lead to various engine issues. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. In small amounts, it remains suspended in the oil; in large amounts, it precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Periodically use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
7
4
Share

What is the reason for the persistent illumination of the Rapid's tire pressure warning light?

The illumination of the tire pressure monitoring indicator light indicates abnormal tire pressure. Abnormal tire pressure generally has the following three causes: Abnormal tire pressure: Typically, an alarm is triggered when the pressure is below 1.8 bar or exceeds 3.0 bar. In this case, tire inspection and pressure adjustment are necessary. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset promptly, the tire pressure monitoring system will continue to record the previous data, causing the tire pressure monitoring indicator light to stay on. Simply performing a tire pressure reset will resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which is used to monitor tire pressure, is directly installed inside the tire and connected to the tire inflation valve. If the sensor is damaged due to impact while driving, it can also cause the tire pressure warning light to illuminate. In the case of sensor damage, the only solution is to replace it with a new component.
4
2
Share

Why is there no air coming out of the two middle vents of the car air conditioner?

The reasons why the car air conditioner is not blowing air are as follows: 1. Check whether the air outlet switch is properly connected and whether there is a short circuit; 2. Check the fuse of the air conditioner to see if it has burned out; 3. Check whether the air outlet of the air conditioner is blocked; 4. Check whether the air conditioner motor fan is working normally; 5. Check the power distribution of the whole vehicle and inspect the battery. More related information is as follows: 1. The car air conditioner is used to adjust and control the temperature, humidity, air cleanliness, and air flow in the car compartment to the optimal state, providing a comfortable riding environment for passengers and reducing travel fatigue; it creates good working conditions for the driver and plays an important role in ensuring safe driving. 2. All car air conditioner vents have a wind direction switch, which is connected to the air duct conversion mechanism. Check whether this switch is set to the middle air outlet position. If not, it is necessary to disassemble the fan under the instrument panel for repair. It is recommended to go to a repair shop for inspection.
10
4
Share

What causes the buzzing sound when stepping on the accelerator in MG6?

MG6 stepping on the accelerator with a buzzing sound may be due to the fuel pump or related components, or a faulty clutch release bearing. Causes of car abnormal noises: It is necessary to check whether there is air leakage in the engine's intake pipe, whether the air filter is installed properly, identify the source of the sound, and whether the engine belt is aging, loose, or slipping. The buzzing sound depends on where it occurs. On the right side of the engine, it is generally the generator belt; on the left, it is an issue with the throttle atmosphere. For the front wheel brake pads, the main reason is likely the brake caliper, with a small part being due to jamming. Solutions for accelerator abnormal noise: You can check the engine oil yourself. If the oil has not been changed for a long time or has deteriorated, these can increase friction between the cylinder valves and guides, as well as hydraulic lifters, leading to abnormal noises when accelerating. When the belt slips, it also produces a buzzing sound. Once the belt slips, it causes high friction temperatures, making the belt stretch longer, which worsens the slipping.
19
1
Share

What is the button under the door of the Audi A4?

The button under the door of the Audi A4 is the vehicle vibration alarm button. It activates the vehicle vibration alarm system. After locking the car, if there is someone inside or vibration on the seats, the vehicle will automatically sound an alarm. This helps prevent situations where children are left inside the car without the driver's knowledge, avoiding potential dangers. To activate the vehicle vibration alarm system, the engine must be started, and the vehicle's electronic system must be engaged. Car Anti-Theft Alarm: The car anti-theft alarm is a multifunctional product. It not only serves as an anti-theft alarm but also includes features such as remote trunk opening, remote door locking/unlocking, remote window control, remote engine start, and remote engine lock. Functions of the Car Alarm: Trigger state recognition function, anti-robbery function; automated central door locking; door ajar warning; vehicle locator/emergency signal, secondary anti-theft; LED indicator, precision electronic detector; remote trunk opening; intrusion warning, power-off memory; automatic anti-theft/non-automatic anti-theft selection, door open flash/no flash selection; engine lock, external emergency deactivation.
13
0
Share

What kind of antifreeze does Volkswagen Polo use?

Volkswagen Polo can use the antifreeze purchased from the 4S store. Method for replacing antifreeze in Volkswagen Polo: Before replacement, let the vehicle stand for 30 minutes to prevent burns from the antifreeze. Locate and loosen the antifreeze drain valve at the bottom of the radiator until all the antifreeze is completely drained. Keep the car idling and continuously add clean water to the antifreeze reservoir to flush out any remaining antifreeze in the cooling system. Stop adding water when the flow becomes colorless, indicating that the old antifreeze has been mostly removed. When the water flow stops, tighten the drain valve and turn off the engine. Add new antifreeze through the filling port until the level is between the MIN and MAX marks. Function of antifreeze: Antifreeze, fully known as antifreeze coolant, is a coolant with antifreeze properties. The engine generates a lot of heat during operation and requires cooling. Antifreeze is the circulating fluid used in the engine cooling system. Therefore, antifreeze is primarily used to dissipate heat from the powertrain.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.