Do I need to wait for the left turn signal to make a U-turn?

1 Answers
DelRobert
07/29/25 12:20am
Whether a vehicle needs to wait for the left turn signal to make a U-turn depends on the actual situation. The following are the scenarios regarding whether a vehicle needs to wait for the left turn signal to make a U-turn: 1. If there is a U-turn signal at the intersection, follow the U-turn signal to make the turn; there is no need to wait for the left turn signal. 2. At an intersection without a U-turn signal but with a left turn signal and marked with yellow solid and dashed lines, generally, as long as there is no no-U-turn sign, separate U-turn signal, or yellow solid and dashed lines, the vehicle is not restricted by the traffic signal. As long as it does not affect the normal flow of traffic and safety is ensured, the vehicle can make a U-turn at any time. 3. If there are yellow solid and dashed lines on the road and the vehicle is on the dashed line side, then a U-turn can be made.
Was this review help?
19
3
Share
More Forum Discussions

How to Add Antifreeze to BYD Song?

BYD Song's antifreeze is located in the radiator overflow tank (found in the engine compartment). Open the hood, the container with red liquid is the coolant reservoir. Simply unscrew the cap and fill it up. Precautions for adding antifreeze: 1. Open the engine hood and check the coolant level in the radiator reservoir. Confirm that it is between the upper (MAX) and lower (MIN) level marks. 2. If the coolant level is at or below the minimum (MIN) mark, add coolant until the level rises to the maximum (MAX) mark. 3. It is recommended to always use BYD-specified coolant without adding any mixtures. Do not mix different brands or types of antifreeze. 4. Before opening the overflow tank, ensure both the engine and overflow tank have completely cooled down. Opening the overflow tank while the engine is still hot may cause coolant to spray out, resulting in severe burns.
6
5
Share

Where does brake fluid leak from?

Brake fluid can leak from the following locations: 1. Brake hose rupture (leakage occurs between the brake pump and the hose). The brake hose is the component that connects the brake pump to the brake caliper. When the brake pedal is pressed, brake fluid is transmitted through the hose to the caliper piston, which then pushes the brake pads against the brake disc to create braking force. If the brake hose ruptures, it will inevitably lead to fluid leakage. 2. Damaged sealing O-ring (leakage occurs at the O-ring). Brake fluid is highly corrosive. Although sealing O-rings are designed to resist this, they will degrade over time, reducing their sealing effectiveness and leading to fluid leakage. 3. Loose or damaged hose screw (leakage occurs at the brake fluid drain hole). The hose screw is used to seal the brake fluid inside the hose. If the hose screw becomes damaged, it will naturally result in fluid leakage.
2
2
Share

What is the maximum wading depth of the Wrangler?

According to official information, the maximum wading depth of the Wrangler is 85 cm. Common tire specifications are 255/70R18 and 245/75R17, with body lengths of 4882mm and 4334mm, and a vehicle weight ranging from 1843kg to 2049kg. The body structure is available as a 4-door 5-seat SUV and a 2-door 4-seat SUV. The maximum wading depth refers to the deepest water a vehicle can safely pass through. Generally, the maximum wading depth for sedans does not exceed 30 cm, while SUVs have a higher maximum wading depth, but it is still best not to exceed 50 cm. Among common models, the GAC Trumpchi GS8 has a maximum wading depth of 30 cm, the Audi A4 has 32 cm, the Volkswagen Sagitar has 30 cm, the Land Rover Range Rover has 90 cm, the Jeep Compass has 48 cm, and the Highlander has 45 cm. The maximum wading depth of SUVs is significantly higher than that of sedans. Generally, when driving through water, vehicle owners should take different measures depending on the depth of the water and the vehicle's characteristics, as follows: If the wading depth reaches the height of the exhaust pipe, it is relatively safe. Even if water enters the exhaust pipe, the pressure inside is sufficient to expel the water. As long as the engine is not turned off in the water, water will not flow back into the vehicle. If the wading depth reaches the height of the door frame, it becomes more dangerous. The vehicle's circuits, electronic components, and sensors are mostly concentrated at the bottom of the car, which could lead to circuit failures, damaging critical electrical components and preventing the car from starting normally. If the wading depth reaches the height of the intake pipe, it is extremely dangerous. Driving directly into such a section could cause the vehicle to stall immediately, leading to permanent engine damage or rendering the engine unusable.
9
0
Share

How to Start the Engine When the Baojun 530 Has No Power?

Methods to start a Baojun 530 when the battery is dead: 1. Push-start method: First, turn the key to the ignition position, press the clutch, release the handbrake, and set the gear to 1st or 2nd. Keep the clutch pressed and start pushing the car. When the speed reaches 5 km/h, slowly release the clutch and press the accelerator to start the engine. 2. Jump-start method: Open the hoods of both cars. Connect the negative terminal of the jumper cable to the negative terminal of the dead battery and the other end to the negative terminal of the donor car's battery. Similarly, connect the positive terminal of the jumper cable to the positive terminal of the dead battery and the other end to the positive terminal of the donor car's battery. Then, start the donor car and rev the engine slightly. Try starting the dead car. 3. Towing-start method: Use a sturdy tow rope to securely tie the front and rear of both cars together. Begin towing slowly, ensuring both cars maintain a steady speed and paying attention to safety. Once the towed car starts, notify the towing car immediately and slowly pull over to the side of the road to stop.
16
4
Share

What is the Difference Between Hybrid Electric and Plug-in Hybrid Vehicles?

Here is an introduction to the differences between the two: 1. Power difference. Plug-in hybrids are usually designed with the main goal of enhancing vehicle performance, such as the Ferrari SF90, Porsche Cayenne, Panamera Plug-in Hybrid, and BYD Dynasty series. In this regard, Chinese brands have performed exceptionally well. For example, BYD's DM models have nearly double the power compared to their fuel-powered counterparts. Of course, some are aimed at improving smoothness, such as BMW plug-in hybrids, Volkswagen plug-in hybrids, and Geely. Others focus on energy efficiency, such as Korean brands and SAIC-GM plug-in hybrids. 2. Driving experience. Plug-in hybrids are typically equipped with large batteries, enabling pure electric driving for 50-100 kilometers. If battery costs decrease, this range may increase in the future. Hybrid electric vehicles, on the other hand, only come with small batteries and can hardly drive purely on electricity. Although they have an EV mode, the engine needs to start and assist in charging after just 1-2 kilometers of pure electric driving. 3. Driving environment. Hybrid electric vehicles save fuel mainly in urban areas; on highways, their fuel consumption is almost the same as that of conventional fuel vehicles, and sometimes even higher. Examples include Toyota's dual-engine models.
19
4
Share

Is a Fuel Consumption of 9-10L Normal for the Mistra?

A fuel consumption of 9-10L for the Mistra is considered normal. In actual driving conditions, factors such as inadequate driving skills, poor engine condition, and lack of maintenance can lead to increased fuel consumption. The combined fuel consumption of the Mistra is 5.3L/100km. There are currently 5 models of the Mistra available for sale: the DCT-LUX Premium Edition, DCT-TOP Flagship Edition, CVT-GLS Leading Edition, CVT-GLX Elite Edition, and CVT-LUX Premium Edition, all with a combined fuel consumption of 5.3L/100km. The above figures are based on the NEDC combined fuel consumption, which measures the fuel consumption data under the NEDC test cycle. The actual fuel consumption is higher, ranging from 6.0-11.0L/100km. Methods to reduce fuel consumption: Clean engine carbon deposits: Excessive carbon deposits in the engine are a significant cause, often due to using unsuitable fuel. It is recommended to add a certain amount of cleaning agent when refueling. If the effect is not noticeable, it indicates a high level of carbon deposits in the engine. In such cases, the car should be taken to a 4S shop for professional cleaning of the engine carbon deposits by technicians. Check the oxygen sensor: As an internal control unit of the car, the oxygen sensor monitors the air-fuel ratio in the engine. If it is damaged, it can cause an imbalance in the air-fuel ratio, leading to a sudden increase in fuel consumption. When the oxygen sensor is damaged, the exhaust pipe emits darker-colored exhaust gases during driving, and the sensor should be replaced immediately. Regularly replace the three filters: During vehicle use, the oil filter, air filter, and fuel filter must be replaced regularly. If not replaced for a long time, they can become dirty and send incorrect information to the engine control unit, resulting in incomplete fuel combustion and increased engine carbon deposits. Check the electronic control unit: Although the engine's electronic control unit is highly reliable, in older vehicles, various faults may occur.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.