Do I need to reapply for a lost vehicle license when scrapping the vehicle?

1 Answers
OJonathan
07/30/25 5:01am
You need to reapply for a lost vehicle license when scrapping the vehicle. Below is the procedure for reissuing a lost vehicle license for a scrapped vehicle: 1. Lost or damaged motor vehicle license: If the motor vehicle license is lost or damaged, you can apply for a replacement at the vehicle management office of the registration location. When applying, the vehicle owner should fill out the application form and submit identification documents. The vehicle management office should reissue or replace the license within one day from the date of acceptance. 2. Fill out the application form: Complete the application form, submit the vehicle for inspection, and provide the required documents. 3. Within two days from the date of acceptance: The vehicle management office should confirm the vehicle, verify the vehicle identification number imprint, review the submitted documents, and issue the motor vehicle registration certificate, license plate, vehicle license, and inspection compliance mark within two days from the date of acceptance.
Was this review help?
20
1
Share
More Forum Discussions

How to adjust the time on the 8th generation Accord?

The method to adjust the time on the 8th generation Accord: Press and hold the SOUND button until you hear a beep, and the time on the LCD display will start flashing. Then, press the 4 button to adjust the hour, the 5 button to adjust the minutes, and the 6 button to set the minutes to 00. After adjusting to the correct time, press the SOUND button again, and the time will stop flashing, indicating that the time has been successfully set. The 8th generation Honda Accord is equipped with three engines: a 2.0L naturally aspirated engine, a 2.4L naturally aspirated engine, and a 3.5L naturally aspirated V6 engine. In terms of body dimensions, the 8th generation Accord measures 4945mm in length, 1845mm in width, 1480mm in height, and has a wheelbase of 2800mm.
1
1
Share

Where is the cigarette lighter fuse located in the Mazda6?

The cigarette lighter fuse in the Mazda6 is located inside the fuse box near the driver's left foot. Here is some information about the cigarette lighter: 1. The cigarette lighter is a component found in all cars, designed to provide a flame source for smokers. 2. Some cigarette lighter sockets remain powered even after the car is turned off, so it's better to plug and unplug devices as needed. When plugging or unplugging devices, avoid shaking them too forcefully, as this can lead to poor contact during subsequent use. In more severe cases, it may cause a short circuit, resulting in the fuse and external device burning out. Therefore, always remove devices vertically. 3. Remember to regularly clean the cigarette lighter socket to remove any foreign objects. Never allow conductive materials such as metal objects or liquids to enter, as this can cause short circuits and fuse blowouts.
3
5
Share

What Causes Abnormal Noise and Failure to Start When Igniting the Car?

The reasons for abnormal noise and failure to start when igniting the car are: insufficient battery power or low voltage. 1. Before turning off the car, forgetting to turn off the headlights or some electrical equipment may cause the battery to drain, resulting in insufficient power. 2. If the battery has been used for too long and is severely aged, the voltage may be insufficient, requiring replacement. Additional information: The method to determine whether the battery has sufficient power is: Turn the ignition key to the ON position (for push-button start models, press the start button twice without stepping on the brake), turn on the headlights, and observe if the light dims significantly or does not light up at all. You can also press the horn; if the sound is noticeably weaker than usual or does not sound at all, it can be concluded that the battery power is insufficient.
12
1
Share

What does AUTO-H mean on a BMW car?

The AUTO-H button indicator in the car refers to the automatic parking function equipped on BMW vehicles. When waiting at a traffic light, after stepping on the brake to stop the vehicle, this function will automatically engage the parking state, eliminating the need for the driver to keep pressing the brake pedal for a long time. To move again, simply press the accelerator pedal. Here is a brief introduction about AUTO-H: 1. The AUTO-HOLD system in cars is also known as the automatic parking assistance system. Its main function is to automatically determine the vehicle's specific state, pre-tension the electronic parking brake, and thus serve the purpose of parking. 2. This function has an independent button for activation and deactivation on vehicles equipped with an electronic parking brake. The AUTO-HOLD button is located behind the electronic parking brake. To use it, first press this button until the indicator light comes on, and the system will officially enter standby mode.
20
2
Share

Does the Cavalier have tire pressure monitoring?

The Cavalier's Xinyue and Xinshang trims come equipped with a tire pressure monitoring system. The tire pressure monitoring system functions by automatically monitoring the tire pressure in real-time while driving and alerts the driver in case of tire leaks or low pressure to ensure driving safety. Here is more information about the tire pressure monitoring system: 1. There are two main types of tire pressure monitoring systems: one is the indirect type (Wheel-Speed-Based TPMS, WSB), which uses the wheel speed sensors of the car's ABS system to compare the rotational speed differences between tires. The other is the direct type (Pressure-Sensor-Based TPMS, PSB). 2. This system uses pressure sensors installed in each tire to directly measure the tire pressure and transmits the pressure information from inside the tire to a central receiver module via wireless transmitters, then displays the tire pressure data for each tire. The system will automatically alert the driver when the tire pressure is too low or there is a leak.
15
3
Share

Does the Sylphy have ISOFIX interfaces?

The Sylphy is equipped with ISOFIX interfaces. They are located in the crevice between the backrest and the seat cushion of the rear seats, as well as at the upper rear part of the seats. The installation method for the ISOFIX fixation is as follows: 1. Simply align the ISOFIX interface of the child safety seat with the reserved slot on the seat, insert it, and then raise the support rod to complete the installation. 2. If the car does not have ISOFIX interfaces, you can use the LATCH interface for fixation or install ISOFIX interfaces yourself on the rear seats of the car. 3. Compared to the simple ISOFIX interface, LATCH solves the problem of no top fixation and, due to its non-rigid connection, has more lenient requirements for the anchor point positions of the car seats. 4. Locate the LATCH interface position and secure the hook strap to the car's LATCH interface.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.