Do I need to go in person to renew my driver's license?

What does the SVS light on the car dashboard mean?

Car dashboard SVS is the engine fault indicator light. The car dashboard is a device that reflects the working conditions of various vehicle systems, and the instrument panels of different cars vary. Here is some related information about car dashboards: 1. Various lights: Under the dashboard mask, various indicator lights or warning lights are installed, such as the coolant level warning light, fuel level indicator, washer fluid level indicator, charging indicator, airbag warning light, etc. 2. Sensors: The sensor for the water temperature gauge is a thermistor-type sensor. It is fixed with threads on the engine cooling water passage. The thermistor determines the current flowing through the coil winding of the water temperature gauge, thereby driving the pointer to swing.

20

3

Share

Why doesn't the car lock indicator light up?

Car lock indicator light not illuminating is caused by either the vehicle failing to successfully complete the locking operation or a malfunction in the anti-theft alert system. 1. Locking operation: The car lock indicator light not lighting up indicates the vehicle did not successfully complete the locking procedure. Some models provide a light prompt when locking - typically the hazard warning lights will flash once. If this lighting system prompt suddenly disappears during locking. 2. Anti-theft system malfunction: The anti-theft system can only complete the locking operation when in the off state. Additionally, some models equipped with push-button start cannot complete the locking operation if the vehicle isn't turned off, even with all doors closed.

7

3

Share

Is Kentech Exhaust Made in China?

Kentech exhaust is manufactured in the United States. Here are some related tips for car exhaust pipe maintenance: 1. Waterproofing: When driving in rainy weather or going to a car wash, be sure to prevent water from entering the muffler, as this can easily cause rust and affect the use of the exhaust pipe. If water accidentally enters the muffler, start the engine immediately to warm up the car and try to drain the accumulated water from the muffler as much as possible. This is particularly important for exhaust pipe maintenance. 2. Rust Prevention: The best method is to apply some rust-proof oil to ensure better protection. You can first remove the muffler, block the drainage hole at the bottom, add rust-proof oil to the flange, shake the muffler to ensure the rust-proof oil evenly coats the inside of the tube, and then reinstall the muffler.

6

5

Share

Should an automatic transmission car be started in P gear?

P gear and N gear can both be used to start the engine. P gear is the parking gear, while N gear is the neutral gear. Use P gear for long-term parking, and N gear for brief stops such as waiting at a traffic light. Relevant knowledge about starting an automatic transmission vehicle is as follows: 1. Starting an automatic transmission vehicle: Insert the key into the ignition switch, press the brake, and start the engine. 2. Prerequisites for starting in N gear: The vehicle can also be started in N gear, but there is a prerequisite: the key must be turned to the start position (without starting), the dashboard must display OK, press the brake, shift the gear lever from P gear to N gear, and then start the engine. Be sure not to release the handbrake. This method is generally used in repair shops.

9

3

Share

How to notify vehicle relocation with temporary license plates?

Temporary license plates cannot be used to notify the vehicle owner to move the car. Here is some relevant information about temporary license plates: 1. Introduction: Temporary license plates are paper-based motor vehicle license plates issued to allow temporary road use of vehicles, primarily referring to temporary vehicle movement permits issued by the vehicle management authorities for newly purchased vehicles before official registration. 2. Relevant regulations: New vehicles using temporary license plates must not exceed 15 days, and the owner should promptly apply to the vehicle management authority for official license plates. After expiration, penalties may include vehicle impoundment, fines, and point deductions. 3. Penalties: New vehicles using temporary license plates must not exceed 15 days, and the owner should promptly apply to the vehicle management authority for official license plates. After expiration, penalties may include vehicle impoundment, fines, and a 12-point deduction.

17

0

Share

Where are Roewe engines produced?

Roewe uses engines jointly developed by SAIC Motor and General Motors, which belong to the independent brand. The engine model used by Roewe is 20A4E, with a maximum horsepower of 234 hp, a maximum power of 172 KW, a maximum power speed of 5000-5500 rpm, and a maximum torque of 360 Nm. For the daily maintenance of Roewe engines, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust system and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to the mechanical load, with the selection standard not lower than the requirements specified by the manufacturer; Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, the performance deteriorates, which can cause various problems for the engine. To avoid failures, the oil should be changed regularly based on usage conditions, and the oil level should be kept moderate; When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and the oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing the oil to bypass and still carry dirt back to the lubrication parts, accelerating engine wear and increasing internal pollution; Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder generated by component wear to form sludge. When the amount is small, it remains suspended in the oil; when the amount is large, it precipitates from the oil, clogging the filter and oil holes, making engine lubrication difficult and causing wear; Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the normal operation of the engine but also extends the overall lifespan of the radiator and engine.

2

Share

Do I need to go in person to renew my driver's license?

What does the SVS light on the car dashboard mean?

Why doesn't the car lock indicator light up?

Is Kentech Exhaust Made in China?

Should an automatic transmission car be started in P gear?

How to notify vehicle relocation with temporary license plates?

Where are Roewe engines produced?

How often should Freon be added to a car?

What is Indirect Tire Pressure Monitoring?

Is it mandatory to display a probationary sign during the internship period?

What Causes Cylinder Scoring in Car Engines?